Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for MilDef Crete RS11
Summary of Contents for MilDef Crete RS11
- Page 1 NOTEBOOK COMPUTER RS11 User’s Guide (Preliminary Draft)
- Page 2 They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufacturer. Copyright © 2013 MilDef Crete Inc. Trademarks All other brand and product names are trademarks or registered trademarks of...
- Page 3 Revision History: Revision Date Changes Author...
- Page 4 FCC (Federal Communications Commission) Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 5 Regulatory Information/ Disclaimers Installation and use of this computer must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment.
- Page 6 (EMC will update when report is available) Products with the CE Marking comply with both the EMC Directive (2004/108/EC) and the Low Voltage Directive (2006/95/EC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms: CISPR 22 Radio Frequency Interference EN55022...
- Page 7 CE Declaration of Conformity (EMC will update when report is available) It is confirmed to comply with the requirements set out in the Council Directive on the approximation of the laws of the member states relating to Electromagnetic Compatibility (2004/108/EC), Low-voltage Directive (2006/95/EC), the Amendment Directive (93/68/EEC), and the procedures...
- Page 8 Power Conservation This computer consumes much less power than conventional computers. However, power consumption may be further reduced by configuring the Power Management Setup. It is recommended to enable power-saving functions when operating this computer, as Power Management functions do not impact system performance while saving power.
- Page 9 Battery Precautions Only use batteries designed for this computer. Wrong and incompatible batteries may cause explosion, leakage or damage to the computer. Do not remove the battery from the computer while it is powered on. Do not continuously use a battery that has been dropped, or that appears damaged (e.g.
- Page 10 Environmental Information, Material Safety & Recycling All materials used in the manufacturing of this equipment are recyclable or environmentally friendly. Please recycle the packing materials in accordance to local regulations at the end of the product's service life. Notice: The equipment may contain insignificant amount of hazardous substances for health and environment below control level.
-
Page 11: Table Of Contents
TABLE OF CONTENTS CHAPTER ONE - GETTING STARTED ........1 ....................1 NPACKING ..................2 UICK PERATION ................3 PPEARANCE VERVIEW CHAPTER TWO - OPERATING INFORMATION ......8 ....................8 ORKPLACE ....................8 UGGEDNESS ..............8 NSTALLING PERATING YSTEM ..............9 ORK WITH OWER UTTON POST..................9 ... - Page 12 USB C .............28 ONFIGURATION USB C ..........28 ONFIGURATION ELECTIONS IO C ............29 UPER ONFIGURATION RF D ........30 EVICE ONTROL ONFIGURATION EC T ............31 HERMAL ONTROL AC IN BOOT S .................31 USB CHARGE C ............32 ONTROL HEATER THERMAL TEMPERATURE S .........32 ........33 ...
- Page 13 CHAPTER SIX - SPECIFICATIONS ..........46 ....................46 LATFORM CPU .......................46 PCH .......................46 ....................46 EMORY ....................46 ISPLAY ....................46 EYBOARD ....................47 OUCHPAD (SSD)...............47 OLID TATE RIVE I/O P ....................47 ORTS AC A ...................48 DAPTER ....................48 ATTERY ............48 YSTEM IMENSIONS AND EIGHT ..............49 ...
-
Page 14: Chapter One - Getting Started
Getting Started Chapter One - Getting Started Unpacking The following components are shipped along with your computer. If any component is missing or damaged, please notify the dealer immediately. Computer Unit AC Adapter AC Power Cord Utility DVD Quick Guide Chapter One - 1... -
Page 15: Quick Operation
Getting Started Quick Operation Loosen the battery screw, remove the battery insulation sheet, and mount the battery. Connect the AC adapter with the computer and start charging the battery for at least 10 minutes. Turn ON the computer by pressing the power switch. Notice: When ambient temperature is under +5℃... -
Page 16: Appearance Overview
Getting Started Appearance Overview LCD Panel Open Embedded Antennas (Optional): GPS, WiFi/Bluetooth x 2 Embedded Mic LED Indicators Power Indicator (Dual LED): HDD/Heater Indicator: Green (Power) Green (HDD) / Orange (Heater) Flash Green (S3) Charger / Battery lower: Orange / Flashing Orange Power Button Touchpad Touchpad Right and Left click buttons... - Page 17 Getting Started Right View 2.5” SATAIII 7mm SSD Kingston Lock Chapter One - 4...
- Page 18 Getting Started Left View 1 2 3 1. GLAN RJ45 2. USB 3.0 x 1 3. USB 3.0 x 1 with Fast Charger 4. SD Card Slot x 1 Chapter One - 5...
- Page 19 Getting Started Rear View L1 L2 L3 L4 L5 DC Power Jack (Std.: DC-in 2-pin; optional: Military 3-pin) Optional Fisher connectors: - L1: USB2.0 - L2: VGA - L3: RS232 or RS422 - L4: GLAN - L5: Audio Chapter One - 6...
- Page 20 Getting Started Bottom View 1. Optional Multi Bay Port 2. Battery pack Chapter One - 7...
-
Page 21: Chapter Two - Operating Information
Operating Information Chapter Two - Operating Information Workplace A clean and moisture-free environment is preferred. Make room for air circulation. Remember to avoid areas from: Sudden or extreme changes in temperature. Extreme heat. Strong electromagnetic fields (near television set, motor rotation area, etc.). -
Page 22: Work With Power Button
Operating Information Work with Power Button Since the notebook computer is equipped with a heater kit to enable the unit to work under low temperature, the heater will first heat HDD up to the temperature set by user, and the system will boot after then. Also, the heater will keep monitoring HDD temperature. -
Page 23: Shut Down
Operating Information Shut down Directly click “Shut down” from your OS to turn OFF the power of your computer. Before shutting down, please do remember to save any unfinished works and close your applications to prevent your SSD from suffering possible data loss or damage. -
Page 24: Intel ® Rapid Start Technology
Operating Information ® Intel Rapid Start Technology ® Your notebook computer can operate Intel Rapid Start Technology when SSD is installed. This technology enables your system resume time not only to be as fast as wake-up time from S3 (Sleep) mode, but also to be more energy saving. -
Page 25: Touchpad
Operating Information Touchpad The touchpad features large-area, multi-touch, and Windows 8 supported. For usage details, please see the following table. Item Description Touchpad Similar to left button of mouse Left-click button Similar to right button of mouse Right-click button Note: You can press Fn+F12 to enable/disable touchpad function. -
Page 26: Keyboard
Operating Information Keyboard The keyboard is functionally equivalent to a full size desktop keyboard. A sample layout is shown as below. Function Key Combinations Description [Fn] + [F1] [Fn] + [F2] Decrease LCD brightness [Fn] + [F3] Increase LCD brightness [Fn] + [F4] Mute [Fn] + [F5]... -
Page 27: Managing Solid Static Drive (Ssd)
Operating Information Managing Solid Static Drive (SSD) The Solid Static Drive (SSD) is a 2.5” type/ 7mm height standard SATAII/III interface data storage device. Some functions, such as Rapid Start Technology, are required to use SSD for operation. Using SD Card The card slots are located at the bottom-right side of your notebook computer. -
Page 28: Rtc
Operating Information Battery backed up RTC (Real Time Clock/Calendar) is built in an on-board CMOS (Complementary Metal Oxide Semiconductor) chip. The RTC keeps track of the time and date while the computer is off. The CMOS chip also stores system setup information. RTC battery is also recharged when AC adapter is attached. -
Page 29: Save Guard The Computer
Operating Information Save Guard the Computer Plug the Kensington lock into the slot near the SSD module and lock it. Both the computer and SSD are secured. Note: Kensington lock is a widely available 3rd party product. Chapter Two - 16... -
Page 30: Wireless Devices (Option)
Operating Information Wireless Devices (Option) For your ease of operations, you can turn on/off your wireless devices through the proprietary software application - “Device Power Manager”. Note: Depending on the configuration of your notebook computer, your Device Power Manager menu may appear differently from the screenshots provided in this section. - Page 31 Operating Information Bluetooth Driver & Application Installation: Install the Bluetooth driver first. Then, install the Wireless Manager. Launch the Device Power Manager: Launch the Device Power Manager. Click “Bluetooth” for enabling the Bluetooth function (click again for disabling the Bluetooth function). Once the Bluetooth starts up, the RF LED will turn on accordingly.
- Page 32 Operating Information Driver & Application Installation: Install the GPS driver first. Then, install the Device Power Manager. Launch the Device Power Manager: Launch the Device Power Manager. Click “GPS” for enabling the GPS function (click again for disabling the GPS function). Once the GPS starts up, the RF LED will turn on accordingly.
-
Page 33: Chapter Three - Managing Power
Managing Power Chapter Three - Managing Power AC Adapter The AC adapter performs two functions: It powers the computer from an external AC source. It charges the computer battery. The adapter automatically detects the AC line voltage (100V or 240V) and adjusts accordingly. -
Page 34: Battery
Managing Power Battery The power source will automatically switch to battery when the external power source (AC adapter or optional vehicle adapter) is disconnected. Battery Low When the battery is nearly exhausted, the computer gives the following “Battery Low” warnings: Windows battery low warning (when operating system is Windows). - Page 35 Managing Power Battery Power Saving Tips The computer comes with an intelligent power-saving feature. You may extend the battery life by: Setup power saving functions in Operating System Power Management options (e.g. Windows Power Options). Lower the intensity of the display by brightness control. Use standby option when computer is temporarily not in use.
-
Page 36: Power Conservation
Managing Power Power Conservation This computer consumes much less power than conventional computers. However, power consumption may be reduced by configuring the Power Management Setup properly. It is recommended the power saving functions to be enabled even when not running on battery power. Power Management will not degrade performance while saving power. -
Page 37: Chapter Four - Bios Setup
BIOS Setup Chapter Four - BIOS Setup Press [F2] at boot up to enter BIOS setup. Use arrow keys to select options and [+/-] to modify them. When finished, move to “Exit” and press [Enter] then confirm save by pressing [Y]. Main Menu Aptio Setup Utility Main... -
Page 38: Advanced Menu
BIOS Setup Advanced Menu Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Trusted Computing ► Trusted Computing Setting ► SATA Configuration ► Intel (R) Rapid Start Technology ► USB Configuration ► Super IO Configuration : Select Screen →←... - Page 39 BIOS Setup Advanced Menu Selections You can make the following selections on the Advanced Menu. Feature Options Description Trusted Disabled TPM Support Computing Enabled SATA SATA Mode SATA Mode Selection: Configuration Selection IDE/AHCI/RAID SATA Test Mode SATA Test Mode: Enabled/Disabled Aggressive LPM Support Aggressive LPM Support:...
-
Page 40: Sata Configuration Sub-Menu
BIOS Setup Feature Options Description HEATER HEATER TEMPERATURE TEMPERATU SETTING FOR HDD THERMAL RE SETTING Intel Smart Disabled Intel Smart Connect Technology Connect Settings Enabled Technology Intel 82579LM NIC Configuration Configure Gigabit Ethernet device Gigabit parameters Blink LEDs (range Network 0/15 seconds) Connection Link Status... -
Page 41: Usb Configuration Sub-Menu
BIOS Setup Gen1 SATA Indicate the maximum speed the Controller SATA controller can support. Gen2 Speed Gen3 USB Configuration Sub-Menu Aptio Setup Utility Advanced Enables Legacy USB Configuration support. AUTO option disables USB Devices: legacy support if no USB 1 Drive, 2 Hubs devices are connected. -
Page 42: Super Io Configuration Sub-Menu
BIOS Setup should be claimed by EHCI driver. Generic Auto Mass storage device emulation Storage type. ‘UTO’ enumerates devices Floppy Device 0.00 according to their media format. Forced FDD Optical drives are emulated as Hard Disk ‘CDROM;’ drives with no media CD-ROM will be emulated according to a drive type. -
Page 43: Rf Device Control Configuration Sub-Menu
BIOS Setup Feature Options Description Serial Port Disabled Enable or Disable Serial Port (COM) Enabled Change Auto Select an optimal setting Settings for Super IO device. IO=3F8h; IRQ=4; IO=3F8h; IRQ=3,4,5,6,7,10,11,12; IO=2F8h; IRQ=3,4,5,6,7,10,11,12; IO=3E8h; IRQ=3,4,5,6,7,10,11,12; IO=2E8h; IRQ=3,4,5,6,7,10,11,12; RF Device Control Configuration Sub-Menu Aptio Setup Utility Advanced RF Device Control Setting... -
Page 44: Ec Thermal Control Sub-Menu
BIOS Setup EC Thermal Control Sub-Menu Aptio Setup Utility Advanced EC Thermal Control EC Thermal Control Setting Thermal cooling trip point [87 C] : Select Screen →← ↑↓: Select Item Enter: Select –/+: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save &... -
Page 45: Usb Charge Control Sub-Menu
BIOS Setup USB CHARGE Control Sub-Menu Aptio Setup Utility Advanced USB CHARGE Setting USB CHARGE Control USB CHARGE Control [Disabled] : Select Screen →← ↑↓: Select Item Enter: Select –/+: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save &... -
Page 46: Intel Smart Connect Technology Sub-Menu
BIOS Setup HEATER TEMPERATURE SETTING Sub-Menu Selections You can make the following selections on the RF Security Control sub-menu. Feature Options Description HEATER -10 C HEATER TEMPERATURE TEMPERATURE Setting for HDD THERMAL SETTING Disabled -10 C HEATER HEATER TEMPERATURE TEMPERATURE Setting for HDD THERMAL SETTING Disabled... - Page 47 BIOS Setup INTEL 82579LM Gigabit Network Connection Sub-Menu Selections You can make the following selections on the RF Security Control sub-menu. Feature Options Description NIC Configuration LINK Speed Change link speed and duplex for current port. Wake on LAN Enable this option to wake the system with a magic packet Link Status HEATER...
-
Page 48: Chipset Menu
BIOS Setup Chipset Menu Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit PCH Parameter ► PCH-IO Configuration ► System Agent (SA) Configuration : Select Screen →← ↑↓: Select Item Enter: Select –/+: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save &... - Page 49 BIOS Setup PCH-IO Configuration Sub-Menu Selections You can make the following selections on the PCH-IO Configuration sub-menu. Feature Options Description Disabled Enable or disable onboard NIC. Controller Enabled Wake on LAN Disabled Enable or disable integrated LAN to wake the system Enabled Disabled USB Configuration settings...
-
Page 50: Boot Menu
BIOS Setup Boot Menu Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Sets system boot Boot Option Priorities order Boot Option #1 [Generic Storage Dev…] Boot Option #2 [IBA GE Slot 00C8 v...] Network Device BBS Priorities : Select Screen →←... -
Page 51: Security Menu
BIOS Setup Security Menu Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Administrator Password Description Password If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup. -
Page 52: Save & Exit Menu
BIOS Setup Save & Exit Menu Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Exit system setup after Save Changes and Exit saving the changes Discard Changes and Exit Save Changes and Reset Discard Changes and Reset : Select Screen →←... -
Page 53: Chapter Five - Drivers And Applications
Drivers and Applications Chapter Five - Drivers and Applications (SW will update info.) The Utility DVD includes all the drivers for the installed devices in your notebook computer. Please consult the dealer if there is any driver missing. Also, through Device Manager in Windows, you are able to perform “Driver Update”... -
Page 54: Audio
Drivers and Applications Audio Windows 7/Ultimate 64-bit: "Setup.exe" directory "\Drivers\Windows (64-bit)\Audio\6777_PG360_Win8_Win7_Vista_XP", and then follow the instructions to install. Windows 7/Ultimate 32-bit: "Setup.exe" directory "\Drivers\Windows (32-bit)\Audio\6777_PG360_Win8_Win7_Vista_XP", and then follow the instructions to install. Intel ME Windows 7/Ultimate 64-bit: "Setup.exe" directory "\Drivers\Windows (64-bit)\Intel_ME\MEI_allOS_7.1.40.1161_PV", then follow... -
Page 55: Wireless Power Manager
Drivers and Applications Wireless Power Manager Windows 7/Ultimate 64-bit: Run "setup.exe" in the directory of "\Utilities\", and then follow the instructions to install. Windows 7/Ultimate 32-bit: Run "setup.exe" in the directory of "\Utilities\", and then follow the instructions to install. Touch Screen Windows 7/Ultimate 64-bit: Run "setup.exe"... -
Page 56: Ricoh
Drivers and Applications Ricoh Windows 7/Ultimate 64-bit: "setup.exe" directory "\Drivers\Windows (64-bit)\Ricoh\Ricoh_Media_Driver_v2.13.16.01", then follow instructions to install. Windows 7/Ultimate 32-bit: "setup.exe" directory "\Drivers\Windows (32-bit)\Ricoh\Ricoh_Media_Driver_v2.13.16.01", then follow instructions to install. Turbo Boost Monitor Windows 7/Ultimate 64-bit: Turbo Boost Monitor : Run "setup.exe" in the directory of "\Drivers\Windows 7 (64-bit)\IntelR Turbo Boost Technology Monitor", and then follow the instructions to install. -
Page 57: Nd Gigabit Lan (Option )
Drivers and Applications 2nd Gigabit LAN (Option) Windows 7/Ultimate 64-bit: "setup.exe" directory "\Drivers\Windows (64-bit)\RTL8111E\Install_Win7_7046_07202011", then follow instructions to install. Windows 7/Ultimate 32-bit: "setup.exe" directory "\Drivers\Windows (32-bit)\RTL8111E\Install_Win7_7046_07202011", then follow instructions to install. WiFi (Option) Windows 7/Ultimate 64-bit: "iprodifx.exe" directory "\Drivers\Windows (64-bit)\Intel_WiFi6230\WLAN", and then follow the instructions to install. *: Then into the“Wireless Power Manager”to turn on the WLAN device. -
Page 58: Gps (Option)
Drivers and Applications GPS (Option) Windows 7/Ultimate 64-bit: *: First into the "Wireless Power Manager" to turn on the GPS device. Run "ublox_A4_U5_USB_drv3264_install_UI.exe" in the directory of "\Drivers\Windows 7 (64-bit)\UBlox 6H Driver", and then follow the instructions to install. Windows 7/Ultimate 32-bit: *: First into the "Wireless Power Manager"... -
Page 59: Chapter Six - Specifications
Specifications Chapter Six - Specifications Platform Intel® Chief River Platform Intel® Ivy Bridge i7-3517UE (4MB Intel® Smart Cache Memory) CPU runs at multiple speeds depending on the CPU type and operating system. Also, CPU speed switches automatically by detecting AC adapter/ battery operation and busy state. -
Page 60: Touchpad
Specifications Touchpad Type: Capacitive Touchpad Interface: PS/2 Solid State Drive (SSD) Type: 2.5” (Removable) Height: Interface: SATAII/III SSD I/O Ports Left: SD Card Slot x 1* Std. GLAN RJ45 (on board Intel GLAN) USB 3.0 USB 3.0** Bottom: Optional Multi Bay port x 1*** Rear: DC-in Connector x 1 (Std. -
Page 61: Ac Adapter
Specifications AC Adapter AC Input: 100 - 240 V Frequency: 50/60 Hz DC Output: Maximum Power: 90 Watts Max. Output Dimension: 130mm (W) x 60mm (D) x 34mm (H) Weight: 430 g (0.9 lb.) Battery Type: Removable Li-Polymer Battery Pack Capacity: 11.1V 6300mAh Dimension:... -
Page 62: Materials And Recycling
Specifications Materials and Recycling Materials of the computer are as follows: Plastic Case: Recyclable UL grade PC + ABS GE C2800 or C6200 Aluminum Case: AL6061T6 Bracket: Aluminum 5052, Steel with nickel plating, stainless steel S304 Cushion Pad/Button: Natural Rubber PCB: FR-4, UL 94V0 Battery:... -
Page 63: Chapter Seven - Optional Devices
Optional Devices Chapter Seven - Optional Devices Communication WiFi/Bluetooth: Intel® Centrino® Advanced-N 6235, Dual Band Board Form Factor: PCIe Half Mini Card Wi-Fi Certified: 802.11 a/b/g/n Bluetooth: Supports BT 2.1, 2.1+EDR, 3.0, 3.0+HS, 4.0 (BLE) Interface: PCIe (WiFi)/USB (BT) GPS: u-blox LEA-6H (USB interface) Gigabit LAN: 1Gbps (internal Mini PCIe Card) Memory Card The memory card will expand your memory to facilitate better system... -
Page 64: Trust Platform Module (Tpm)
Optional Devices Trust Platform Module (TPM) There is an optional Trust Platform Module (TPM) equipped with this notebook computer for users to strengthen the security. With TPM, users are able to encrypt the folders and files directly and make the important file be more secure and be with an additional protection. -
Page 65: Chapter Eight - Maintenance And Service
Maintenance and Service Chapter Eight - Maintenance and Service Cleaning ALWAYS turn OFF the power, unplug the power cord and remove the battery before cleaning. The exterior of the system and display may be wiped with a clean, soft, and lint-free cloth. -
Page 66: Rma Service
Maintenance and Service RMA Service If troubleshooting steps are unsuccessful, consult your dealer for RMA. Shipping instructions: Remove any personal disks or other media. Use the original shipping container and packing materials, if possible. If the original packing materials are not available, wrap the equipment with soft material (e.g. - Page 67 FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Need help?
Do you have a question about the RS11 and is the answer not in the manual?
Questions and answers