Advertisement
Quick Links
LSX Tonneau Cover
INSTALLATION INSTRUCTIONS
To
Tools
o
ols
• Wire .125" (1/8") "T" Wrench
• .50" (1/2") Box Wrench
• 4mm Hex Driver
• .50" (1/2") Socket Wrench
• Box Knife
Easy
Easy step-by-step wiring installation instructions
step-by-step
wiring
installation
instructions
als
also available online in Microsoft
also a
o
avai
va
lab
able
l
l
onl
on
ine
ne
in
in
Micro
Mi
crosof
sof
oft
t
t
®
®
Po
Po
Po
PowerPoint
o
wer
wer
e
Point
Poi
for
f
for
for
format at: https://www.aredealer.com
mat
mat
t
at
a
at: h
: h
h
ttp
ttp
ttps:/
p
p
s:/
s s :
/ww
/www.a
w.ared
redeal
ealer.
l
er.
r
r
com
com
om
TONNEAU COVER
Content
Contents
t
• 1 Tonneau Cover Assembly
• 1 Accessory Carton with a
model specific Clamp System
nt
s
Advertisement
Related Manuals for ARE LSX
Summary of Contents for ARE LSX
-
Page 1: Installation Instructions
Easy step-by-step wiring installation instructions Easy step-by-step wiring installation instructions also available online in Microsoft also a avai able Micro crosof ® ® PowerPoint Point format at: https://www.aredealer.com at: h ttps:/ s s : /www.a w.ared redeal ealer. LSX Tonneau Cover... - Page 2 Moveable “T” Nut Covers Accessories Package Position “T” nuts at desired clamp locations. Contents Raise LSX above head level. Remove dunnage by loosening clamp bolt. .125" (1/8") “T” Wrench 1.5" Cap Tape .50" (1/2") Box Wrench 4mm Hex Driver Grease .50”...
- Page 3 Cut tape at end cap. Once tonneau is set into place, cut prop assist arm tie wraps. Palm Handle Lock/Latch Side Rail Tailgate Masking Tape LSX Tonneau Cover Step 2: Positioning Mylar Backed Cap Tape Unlock and unlatch palm handle. Raise tonneau, close Ttailgate Apply paper backed cap tape to hinge base toward the Place protective masking tape at both front corners.
- Page 4 Cover Plate Rear Rubber-Headed Bumper Bolt Clamp Jaw M8 bolt and Stainless Washer After all installation adjustments are made, snap cover Raise and jower the tonneau cover to verify fit. Adjust plates in place. Loosely assemble clamp jaw system. rubber-headed bumper bolts as required in rear locations.
- Page 5 Remove four screws in shroud to access locking mechanism. Once After latch rod length is determined, secure latch rods adjustments are made reposition shroud using the same 4 screws. by tightening set screws uniform gap between truck bed and tonneau cover.
- Page 6 Proper Closing Sequence Cycle palm handle latch and rod system to assure smooth Monthly lubrication locations, both sides. operation. Make adjustments if necessary. Protective Tape DO NOT LUBE GAS PROP RODS; CLEAN ONLY Remove protective tape when all adjustments are complete.
- Page 7 Must Specify Assembled View 3-9/16 13771 Bulkhead Seal Must Specify Length Exploded View 11353 11351 11411 LSX Corner 11412 LSX Corner Attachment Passenger’s Side Driver’s Side Machine Screw Rail System Spare Parts — Assembled View Palm Handle — Exploded View...
- Page 8 The LSX is the ultimate in custom fitted hard tonneau covers for today’s pickups. A.R.E. designed each model to match the curvature and style lines of the pickup it is made to fit. Compound curves add strength as well as style.
Need help?
Do you have a question about the LSX and is the answer not in the manual?
Questions and answers