Related Manuals for IEI Technology MODAT-100
Summary of Contents for IEI Technology MODAT-100
- Page 1 MODAT-100 IEI Technology Corp. MODEL: MODAT-100 Industrial PDA with Barcode Scanner for Ticketing, Membership Verification, Real-time Transactions User Manual Page 1 Rev. 1.04 – 12 March, 2012...
- Page 2 MODAT-100 Revision Date Version Changes 12 March, 2012 1.04 Added note to Section 2.3 Charging the System and Section 2.5 Power-On/Off Procedure 9 September, 2011 1.03 Updated Section 1.5 Specifications 8 August, 2011 1.02 Added printing notice to Pg. 4 Update to Section 2.3: Charging the System...
- Page 3 MODAT-100 Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
- Page 4 MODAT-100 WARNING This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
-
Page 5: Table Of Contents
MODAT-100 Table of Contents 1 INTRODUCTION......................1 1.1 O ........................2 VERVIEW 1.2 F ........................2 EATURE 1.3 A ......................3 PPLICATIONS 1.4 E ....................3 XTERNAL VERVIEW 1.4.1 Front Panel ......................4 1.4.1.1 Keypad ......................6 1.4.2 Left Panel ......................7 1.4.3 Right Panel...................... - Page 6 MODAT-100 A.2.1 Maintenance and Cleaning................25 A.2.2 Cleaning Tools ....................26 B INTERNATIONAL STANDARDS COMPLIANCE ..........27 B.1 EN 60601-1, EN 60601-2 ..................28 B.2 FCC......................... 28 C HAZARDOUS MATERIALS DISCLOSURE ............29 C.1 H IPB P AZARDOUS ATERIALS ISCLOSURE...
- Page 7 Figure 1-8: MODAT-100 Dimensions (units in mm)..............12 Figure 2-1: MODAT-100 DC-IN Adapter Port ................16 Figure 2-2: Battery LED......................17 Figure 2-3: Connect the MODAT-100 to the Charging Cradle..........17 Figure2-4: Removing the Battery Cover ................. 18 Figure2-5: Removing the Battery.................... 19 Figure2-6: Inserting the SIM/SAM Card ..................
- Page 8 MODAT-100 List of Tables Table 1-1: MODAT-100 System Specifications............... 11 Table 2-1: Packing List......................15 Table 2-2: Optional Items List ....................16 Page 8...
-
Page 9: Introduction
MODAT-100 Chapter Introduction Page 1... -
Page 10: Overview
Bluetooth function allows devices such as headsets and thermal printers to be paired with the MODAT-100, increasing the productivity of your staff while on the go. A built-in vibrator alerts staff immediately allowing them to provide prompt service to customers. -
Page 11: Applications
Hospitality 1.4 External Overview The MODAT-100 combines its features in a stylish enclosure. The MODAT-100 consists of a screen, rear panel, top panel, bottom panel and two side panels (left and right). The panels are described in detail in the following sections. -
Page 12: Front Panel
MODAT-100 1.4.1 Front Panel The front panel of the MODAT-100 is shown below. Figure 1-2: MODAT-100 Front Panel 1 x 2” Thermal Printer 1 x Magnetic Stripe Reader 1 x Smart Card Reader 1 x 3.5G WiFi 1 x Battery LED 1 x Keypad The two LEDs on the front panel indicate battery, 3.5G and barcode status as described... - Page 13 MODAT-100 NOTE: The user can adjust the text size showed on the screen by going to “Start” “Settings” “System” “Screen”. Page 5...
-
Page 14: Keypad
MODAT-100 1.4.1.1 Keypad The keypad and its functions are shown below. Figure 1-3: MODAT-100 Keypad Press the “Alpha” key to use the orange characters. Press the “Fn” key to use the blue characters. Page 6... -
Page 15: Left Panel
MODAT-100 1.4.2 Left Panel The left panel of the MODAT-100 is shown below. Figure 1-4: MODAT-100 Left Panel 1 x Barcode Scanner Trigger 1 x MicroSD card slot 1 x Reset button Page 7... -
Page 16: Right Panel
MODAT-100 1.4.3 Right Panel The right panel of the MODAT-100 is shown in Figure 1-5. Figure 1-5: MODAT-100 Right Panel 1 x Barcode Scanner Trigger 1 x Stylus 1.4.4 Bottom Panel The bottom panel of the MODAT-100 is shown below. -
Page 17: Back Panel
1 x 1D Laser Barcode Scanner 1 x 3 Megapixel Camera 1 x Speaker 1 x 7.4V 1880mAh Battery 1.5 Specifications The technical specifications for the MODAT-100 systems are listed in Table 1-1. Specification MODAT-100 Microprocessor Marvell® PXA 310 624MHz Windows Mobile 6.5... - Page 18 MODAT-100 Specification MODAT-100 Memory 256 MB DDR SDRAM 128 MB NAND Flash Display 3.5” (89mm) TFT LCD QVGA (240 x 320) 64 K color LED backlight (sunlight readable) Resistive touchscreen Camera 3 Megapixel CMOS camera with LED Flash Light Communication Wi-Fi 802.11 b/g...
-
Page 19: Table 1-1: Modat-100 System Specifications
+/- 6k Vdc contact discharge Impact Resistance 1.2 m drop survival (excluding SCR/MSR/Printer) Dimensions (LxWxD) 230 mm x 84 mm x 54 mm Net Weight 546 g Barcode Scanner 1D Laser Scan Engine Certifications CE, FCC Table 1-1: MODAT-100 System Specifications Page 11... -
Page 20: Dimensions
MODAT-100 1.6 Dimensions Figure 1-8: MODAT-100 Dimensions (units in mm) Page 12... -
Page 21: Installation
MODAT-100 Chapter Installation Page 13... -
Page 22: Unpacking The Device
Only remove the protective plastic cover stuck to the front screen after installation. The plastic layer protects the screen surface during the installation process. To unpack the MODAT-100, follow these steps: Step 1: Cut the sealing tape. Only cut deep enough to cut the tape. -
Page 23: Packing List
Quantity Item Image MODAT-100 Battery Pack P/N: 31603-000014-RS Carrying Case P/N: 7Z000-MODAT100POUCH-RS Power Adapter P/N: 63000-FSP036RAB613-RS Stylus P/N: 7Z000-MODAT100STYLUS-RS Headset P/N: Z000-EMI164001S-RS Table 2-1: Packing List 2.2.1 Optional Items The following items are optional accessories for the MODAT-100: Page 15... -
Page 24: Charging The System
4 hours. After that, the battery may be charged as needed. To start using the MODAT-100, the user must charge the MODAT-100 by the power adapter. To charge the MODAT-100, please follow the steps below. Step 1: Connect the adapter plug of the power cable to the DC-IN port on the bottom panel of the MODAT-100. -
Page 25: Using The Optional Cradle
To charge the MODAT-100 using the optional charging cradle, follow the steps below. Step 1: Connect the cable to the rear side of the charging cradle (the MODAT-100 is only supported by the USB driver from the Windows XP system). -
Page 26: Installing Asim/Sam Card
When inserting the SIM or SAM card, make sure the notch on the card is in the correct orientation to avoid damage to the card slot. The MODAT-100 supports a Subscriber Identity Module (SIM) and a Security Identification Module (SAM) card slot. -
Page 27: Figure2-5: Removing The Battery
MODAT-100 Figure 2-5: Removing the Battery Step 3: Align the card notch with the upper left hand corner of the MODAT-100. Step 4: Insert the SIM card into the left hand slot until the card clicks into place (C). Step 5: Insert the SAM card into the right hand slot until the card clicks into place (C). -
Page 28: Power -O N /Off Procedure
The MODAT-100 can be synchronized with a PC through USB connection. To synchronize with the Windows 7 system, please make sure to switch the USB mode to RNDIS mode (USB to PC) in the MODAT-100. To switch the USB mode, follow the steps below: Step 1: Power on the MODAT-100. -
Page 29: Figure 2-8: Usb To Pc Window
MODAT-100 Step 2: Go to “Start” “Settings” “Connections” “USB to PC”. Step 3: Check the “Enable advanced network functionality” option. Figure 2-8: USB to PC Window Page 21... -
Page 30: A Safety Precautions
MODAT-100 Appendix Safety Precautions Page 22... -
Page 31: Safety Precautions
Do not apply voltage levels that exceed the specified voltage range. Doing so may cause fire and/or an electrical shock. Electric shocks can occur if the MODAT-100 chassis is opened when the MODAT-100 is running. Do not drop or insert any objects into the ventilation openings of the MODAT-100. -
Page 32: Anti-Static Precautions
Electrostatic discharge (ESD) can cause serious damage to electronic components, including the MODAT-100. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the MODAT-100 is opened and any of the electrical components are handled, the following anti-static precautions are strictly adhered to. -
Page 33: Product Disposal
When maintaining or cleaning the MODAT-100, please follow the guidelines below. A.2.1 Maintenance and Cleaning Prior to cleaning any part or component of the MODAT-100, please read the details below. Except for the LCD panel, never spray or squirt liquids directly onto any other components. -
Page 34: Cleaning Tools
In such case, the product will be explicitly mentioned in the cleaning tips. Below is a list of items to use when cleaning the MODAT-100. C loth – Although paper towels or tissues can be used, a soft, clean piece of cloth is recommended when cleaning the MODAT-100. -
Page 35: B International Standards Compliance
MODAT-100 Appendix International Standards Compliance Page 27... -
Page 36: Fcc
MODAT-100 B.1 EN 60601-1, EN 60601-2 The LCD monitor complies with the EN 60601-1 and EN 60601-2 of related European standards. B.2 FCC We hereby declare that the equipment specified above conforms to the technical standards as specified in the FCC Rules. -
Page 37: C Hazardous Materials Disclosure
MODAT-100 Appendix Hazardous Materials Disclosure Page 29... -
Page 38: Ercury
MODAT-100 C.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only. -
Page 39: Modat
MODAT-100 Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd) Chromium Biphenyls Diphenyl (CR(VI)) (PBB) Ethers (PBDE) Housing Display Printed Circuit Board Metal Fasteners Cable Assembly Fan Assembly Power Supply Assemblies Battery... - Page 40 MODAT-100 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符 合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的 年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元 件将会单独标示出来。 部件名称 部件名称 部件名称 部件名称 有毒有害物质或元素 有毒有害物质或元素 有毒有害物质或元素 有毒有害物质或元素 铅 铅 铅 铅 汞 汞 汞 汞 镉 镉 镉 镉 六价铬 六价铬 多溴联苯 多溴联苯 多溴二苯 多溴二苯 六价铬 六价铬 多溴联苯 多溴联苯...
- Page 41 MODAT-100 provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.