Table of Contents
Advertisement
Quick Links
1. Introduction
· This Installation manual contains information regarding the installation and the safe handling method
of the photovoltaic module (hereafter referred to as "module") supplied by Hyundai Heavy Industries
Co., Ltd. (hereafter referred to as "HHI").
· System Users and Installers should read and understand this guide before handling, installing the
module. For any questions, please contact Customer Support department or our local representatives
for more detailed information.
· Before installing a solar photovoltaic system, mechanical and electrical requirements for the total
system should be checked as well. Keep this guide in a safe place for future reference.
· The installer should conform to every safety precautions specified in this guide and local codes when
installing a module.
· HHI modules are tested and certified for installation worldwide. Different regions may have different
regulations for solar PV installations. In this manual, hereafter "IEC only" is used to refer to regions
where IEC standard applies, e.g. Europe, Middle East, most of Asia Pacific countries; "UL only" is
used to refer to regions where UL standard applies, e.g. United States, Canada; all other references
are global.
2. General Information
This manual provides the installation information for HHI modules. Each individual module has a
unique serial number.
Serial number : YYMMDD-XX-MxxxMG-0001(~9999) (Ex. 110317-21-M235MG-0001)
· YYMMDD : Production date
· XX : Production line
· MxxxMG : Model (xxx : module power range)
· 0001(~9999) : Production number
2.1 Disclaimer of Liability
· The information in this manual is based on HHI's knowledge and experience and is believed to be
reliable; but any information including product specification (without limitations) and descriptions do
not constitute over a warranty.
· HHI reserves the rights for any change the technical specification including the PV production, the
specifications, or the product information sheets without prior notice.
· The installation techniques, handling and use of this product are beyond company control.
· HHI does not have any responsibility and the liability for loss, damage, injury or expense resulting
from improper installation, handling or use.
Sales Office
2nd Fl., Hyundai Bldg.,
75, Yulgok-ro, Jongno-gu,
Seoul 110-793, Korea
INSTALLATION MANUAL
Effective September 1, 2013
Page 1 of 16
www.hhi-green.com/solar
Factory
313, Soi-ro, Soi-myeon, Eumseong-gun,
Chungcheongbuk-do 369-872, Korea
Advertisement
Table of Contents
Related Manuals for Hyundai HiS-MxxxMF
Summary of Contents for Hyundai HiS-MxxxMF
-
Page 1: Installation Manual
1. Introduction · This Installation manual contains information regarding the installation and the safe handling method of the photovoltaic module (hereafter referred to as “module”) supplied by Hyundai Heavy Industries Co., Ltd. (hereafter referred to as “HHI”). · System Users and Installers should read and understand this guide before handling, installing the module. - Page 2 Installers should secure the safe installation status including all electrical hazards. · PID (Potential Induced Degradation) is not covered by Hyundai Limited Warranty for PV Modules. To prevent the PID phenomena, it is recommended to design the system to avoid PID or use the PID- free products.
-
Page 3: General Safety
5mm. Nevertheless, the recommended distance between two modules is 20mm to allow wind circulation, in order to reduce pressure loads and improve module ventilation. Page 3 of 16 Factory Sales Office 313, Soi-ro, Soi-myeon, Eumseong-gun, 2nd Fl., Hyundai Bldg., Chungcheongbuk-do 369-872, Korea 75, Yulgok-ro, Jongno-gu, Seoul 110-793, Korea... - Page 4 1) PV modules shall not be installed in salty area within 500m from a body of salt water and/or area where salty wind hit directly. ※ HYUNDAI modules have passed the IEC61701 test (Salt Mist Corrosion Test) 2) PV modules shall not be immersed in water and shall not be continually exposure to Water from a sprinkler, fountain, etc.
-
Page 5: Mounting Method
· When installing modules in snowy area, additional clamping or supporting parts should be attached to the middle of the lower long side frame to prevent possible damages from slipping snow. Detailed mounting method is described in ‘module installation instruction’ in the appendix. Picture 1. HiS-MxxxMF Hole Position Page 5 of 16 Factory... - Page 6 Picture 2. HiS-MxxxMG Hole Position Picture 3. Installation Method using bolt & nut Page 6 of 16 Factory Sales Office 313, Soi-ro, Soi-myeon, Eumseong-gun, 2nd Fl., Hyundai Bldg., Chungcheongbuk-do 369-872, Korea 75, Yulgok-ro, Jongno-gu, Seoul 110-793, Korea...
- Page 7 Picture 4. Mounting Hardware Picture 5. Installation Method using clamping Page 7 of 16 Factory Sales Office 313, Soi-ro, Soi-myeon, Eumseong-gun, 2nd Fl., Hyundai Bldg., Chungcheongbuk-do 369-872, Korea 75, Yulgok-ro, Jongno-gu, Seoul 110-793, Korea...
-
Page 8: Specifications
· Nominal Electrical Characteristics : Within 3% under STC condition · Standard Test Condition (STC): Irradiation 1,000 W/㎡, Cell Temperature 25 ℃, 1.5 AM · Electrical Characteristics : HiS-MxxxMF (Multi-Crystalline Si Type, 3 Bus Bar Type, 54 Cells) Item HiS-MxxxMF (xxx;Normal Power Value) - Page 9 Safety Qualification & Class IEC 61215 & Class II Maximum Series Fuse Rating [A] Fire Class rating Class C Page 9 of 16 Factory Sales Office 313, Soi-ro, Soi-myeon, Eumseong-gun, 2nd Fl., Hyundai Bldg., Chungcheongbuk-do 369-872, Korea 75, Yulgok-ro, Jongno-gu, Seoul 110-793, Korea...
- Page 10 · Mechanical Characteristics (HiS-MxxxMF/HiS-SxxxMF) Description HiS-MxxxMF/HiS-SxxxMF Length, mm(inches) 1,476 (58.1) Width, mm(inches) 983 (38.7) Depth, mm(inches) 35 (1.38) Weight, kg(pounds) 16.5 (36.6) · Mechanical Characteristics (HiS-MxxxMG/HiS-SxxxMG) Description HiS-MxxxMG/HiS-SxxxMG Length, mm(inches) 1,645(64.7) Width, mm(inches) 983(38.7) Depth, mm(inches) 35 (1.38) Weight, kg(pounds) 18.5(40.8)
-
Page 11: Array Wiring
The material for bolt, nut, washer and lug should be stainless steel. Picture 7. Lay in Ground Lug Page 11 of 16 Factory Sales Office 313, Soi-ro, Soi-myeon, Eumseong-gun, 2nd Fl., Hyundai Bldg., Chungcheongbuk-do 369-872, Korea 75, Yulgok-ro, Jongno-gu, Seoul 110-793, Korea... - Page 12 If installer wishes to apply additional diode, he or she should inform an authorized engineer of HHI. Page 12 of 16 Factory Sales Office 313, Soi-ro, Soi-myeon, Eumseong-gun, 2nd Fl., Hyundai Bldg., Chungcheongbuk-do 369-872, Korea 75, Yulgok-ro, Jongno-gu, Seoul 110-793, Korea...
-
Page 13: Operation And Maintenance
In order to ensure proper operation of the system, please check all wiring connections and the condition of the wire insulation periodically. Page 13 of 16 Factory Sales Office 313, Soi-ro, Soi-myeon, Eumseong-gun, 2nd Fl., Hyundai Bldg., Chungcheongbuk-do 369-872, Korea 75, Yulgok-ro, Jongno-gu, Seoul 110-793, Korea... - Page 14 Picture 9. Standard module Layout & Ground position (HiS-MxxxMF) Picture 10. Standard module Layout & Ground position (HiS-MxxxMG) Page 14 of 16 Factory Sales Office 313, Soi-ro, Soi-myeon, Eumseong-gun, 2nd Fl., Hyundai Bldg., Chungcheongbuk-do 369-872, Korea 75, Yulgok-ro, Jongno-gu,...
- Page 15 Picture 11. Junction box Page 15 of 16 Factory Sales Office 313, Soi-ro, Soi-myeon, Eumseong-gun, 2nd Fl., Hyundai Bldg., Chungcheongbuk-do 369-872, Korea 75, Yulgok-ro, Jongno-gu, Seoul 110-793, Korea...
- Page 16 S/8≤ Clamping Area ≤S/4 Note 1) The certified mounting method is bolting method by TÜV Rheinland. 2) The Mounting method has been qualified by Hyundai Heavy Industries, and the mechanical load tests are based on IEC61215 ed.2. Page 16 of 16...