MS Sedco DHR3 Installation Instructions Manual

Microwave/infrared motion & presence detector for automatic doors

Advertisement

Quick Links

DHR3
Microwave/Infrared Motion & Presence Detector for Automatic Doors
NOTE: Set up for this sensor should be
performed by an AAADM-certified installer.
Section 1
General Description
The DHR3 is a combination microwave/infrared sensor
providing both motion detection and presence detection
in one microprocessor controlled sensor for all types of
automatic doors.
• Wide and narrow pattern width of the sensor
is adjustable.
• Pattern depth and width are adjustable using mounting
height, dip switches, pattern width and pattern angle
adjustments.
• Frequency is selectable in four channels
• Self-Diagnostic means the sensor continuously
monitors itself.
• Snow Mode Switch ensures against false operation
caused by snow, insects, etc.
• Microprocessor provides programmable Presence
Timer (2 sec., 30 sec., 60 sec., or infinity).
Section 2
Parts Identification
Accessories
Mounting
Template
Mounting
Screws
Connection
Cable
Installation
Instructions
Area
Mask
8701 Castle Park Drive  Indianapolis, Indiana 46256
Telephone: (317) 842-2545  www.mssedco.com  custsvc@mssedco.com
INSTALLATION INSTRUCTIONS
Section 3
Mounting Information
1. Do not mount higher than 10.5 ft. (3.2m).
2. Mount within 1.97" (50mm) from the bottom of the
door engine cover.
3. Do not leave any objects which may move in the
detection pattern.
4. Do not mount in a humid or steamy environment.
5. Do not mount where rain or snow will fall directly on
unit.
6. Do not mount where snow or water will accumulate
on floor if possible.
7.
Do not mount in a place where reflection of sunlight
will shine on unit.
8. Use different frequency settings for sensor in close
proximity.
9. The radar part of the DHR3 sensor may be
negatively influenced by metal close to or in the
detection field.
1
2
10.5Ft.
4
5
7
8
Use Alternate Frequency.
To maximize the effectiveness of doorway detection,
install the DHR3 outside and inside as shown below.
Side View
Plan View
A
B
3
6
9
A
B
A
Moving Door Leaf
Moving Door Leaf
B
DHR3v1017
Page 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DHR3 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for MS Sedco DHR3

  • Page 1 8. Use different frequency settings for sensor in close adjustments. proximity. • Frequency is selectable in four channels 9. The radar part of the DHR3 sensor may be • Self-Diagnostic means the sensor continuously negatively influenced by metal close to or in the monitors itself.
  • Page 2: Mounting And Wiring

    DHR3 INSTALLATION INSTRUCTIONS Microwave/Infrared Motion & Presence Detector for Automatic Doors Section 4 Removing cover after installation: Mounting and Wiring 1. Using the mounting template provided, drill mounting and wire holes. 2. Remove cover of unit. Section 5 Dip Switch Settings Dip Switch X 3.
  • Page 3: Detection Area

    DHR3 INSTALLATION INSTRUCTIONS Microwave/Infrared Motion & Presence Detector for Automatic Doors Dip Switch Y Section 6 Detection Area Dip Switches are depicted in the Detection Area Depth Adjustment: IR (Inner 3 Rows) Default position. 1 2 3 4 5 6...
  • Page 4 DHR3 INSTALLATION INSTRUCTIONS Microwave/Infrared Motion & Presence Detector for Automatic Doors Detection Area Depth Adjustment: Radar (Outer). 3. Vacate the Detection Pattern immediately. While the •Detection area varies depending on walking speed. sensor sees ANY moving objects in its DETECTION •Adjustment possible in 3°...
  • Page 5: Verification Of Operation

    Presence Detection: During the “Doorway Learn” process, the outer 3 rows of detection on the DHR3 sensor switch from motion detection to presence detection 10 seconds after power ON. The inner “Doorway Learn”...
  • Page 6 DHR3 INSTALLATION INSTRUCTIONS Microwave/Infrared Motion & Presence Detector for Automatic Doors Section 9 Timing Chart of Events After installation is complete, walk test the detection zone. If the detection zone is not as expected, adjust the detection area as referred to in Section 6.
  • Page 7: Self Monitoring

    DHR3 INSTALLATION INSTRUCTIONS Microwave/Infrared Motion & Presence Detector for Automatic Doors Section 11 CAUSE 3: Sensor Wiring SOLUTION 3: Double check sensor wiring. Self Monitoring When the sensor has an internal sensor error, the door PROBLEM 2: Door operates by itself (ghosting)
  • Page 8 Weight....... 0.56 lbs. (0.26kg) Section 13 Color........Black, Silver Technical Data Accessories....... Cable Mounting Screws (2 pcs.) Model........ DHR3 Mounting Template Detection Method..... Doppler Shift Radar & Installation Instructions Active Infrared Reflection Max. Installed Height..10.5 ft. (3.2m) Section 14 Power Supply....
  • Page 9: Warranty

    Warranty MS SEDCO guarantees this product to be free from manufacturing defects for 3 years from date of installation. Unless MS SEDCO is notified of the date of installation, the warranty will be in effect for 3 years from the date of shipment from our factory. If, during the...

Table of Contents