Unpacking And Checking Equipment; Installation - Kenwood TKR-D710 Instruction Manual

VHF DIGITAL REPEATER/ UHF DIGITAL REPEATER
TKR-D710/ TKR-D810
INSTRUCTION MANUAL
THANK YOU!
We are grateful you purchased this KENWOOD repeater. We
believe this easy-to-program repeater will be highly eff ective in
your communications system, and will keep personnel operating
at peak effi ciency.
PRECAUTIONS
• Do not expose the unit to rain or moisture; to prevent fi re or
electric shock.
• Do not open the unit under any circumstances; to avoid risk of
electric shock.
• Do not expose the unit to long periods of direct sunlight, nor
place it close to heating appliances.
• Do not place the unit in excessively dusty and/or humid areas,
nor on unstable surfaces.
•
Do not put the plastic bag used for packing of this equipment
on the place which reaches a small child's hand. It will
become a cause of suffocation if it wears fl atly.
•
Always switch the transceiver power off before installing
optional accessories.
• If you detect an abnormal odor or smoke coming from the unit,
disconnect the power from the unit immediately. Contact your
KENWOOD service center or dealer.
NOTICES TO THE USER
◆ Government law prohibits the operation of unlicensed radio
transmitters within the territories under government control.
◆ Illegal operation is punishable by fi ne and/or imprisonment.
◆ Refer service to qualifi ed technicians only.
One or more of the following statements may be applicable:
FCC WARNING
This equipment generates or uses radio frequency energy. Changes
or modifi cations to this equipment may cause harmful interference
unless the modifi cations are expressly approved by the party
responsible/JVC KENWOOD. The user could lose the authority to
operate this equipment if an unauthorized change or modifi cation is
made.
INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY
THE FCC
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can generate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
•
Consult the dealer for technical assistance.
Firmware Copyrights
The title to and ownership of copyrights for fi rmware embedded in
KENWOOD product memories are reserved for JVC KENWOOD
Corporation.
◆ Do not install the repeater in explosive atmospheres (infl ammable
gas, dust particles, metallic powders, grain powders, etc.).
◆ This repeater is intended for use as a fi xed base station with
the antenna located outdoors on the rooftop or on an antenna
tower.
◆ This repeater is designed for a 13.6 V DC power source!
Never use a 24 V DC or higher source to power the repeater.
◆ Use only the supplied DC cord.
◆ Do not remove the ferrite core attached to the DC cord. Doing
so may cause interference with radio communications.

UNPACKING AND CHECKING EQUIPMENT

Note: The following unpacking information is for use by your
KENWOOD dealer, an authorized KENWOOD service center, or the
factory.
Carefully unpack the repeater. We recommend that you identify
the items listed in the following table before discarding the packing
material. If any items are missing or have been damaged during
shipment, fi le a claim with the carrier immediately.
Item
Hardware fi xture
Front glass
Name plates
Cushion
Cushion
Foot
Foot
Grommet
Handle
Screws
Screws
DC cord
Lead wire with connector (15 pin)
Fuse
Instruction Manual

INSTALLATION

To install the handles onto the front panel of the repeater, align the
handles with the holes on the front panel, then secure the handles
using the supplied screws.
Please consult your dealer for installing the repeater and antenna.
The AMBE+2 TM voice coding Technology embodied in this product
is protected by intellectual property rights including patent rights,
copyrights and trade secrets of Digital Voice Systems, Inc. This
voice coding Technology is licensed solely for use within this
Communications Equipment. The user of this Technology is
explicitly prohibited from attempting to extract, remove, decompile,
reverse engineer, or disassemble the Object Code, or in any other
way convert the Object Code into a human-readable form. U.S.
Patent Nos. #6,199,037, #6,912,495, #8,200,497, #7,970,606, and
#8,359,197.
1
Part Number Quantity
J21-8559-XX 1
B10-2635-XX 1
B11-1259-XX 1
G13-1801-XX 4
G13-1802-XX 4
J02-0475-XX 2
J02-0492-XX 2
J59-0302-XX 2
K01-0418-XX 1
N30-4006-XX 2
N35-3006-XX 5
E30-3427-XX 1
E31-3228-XX 1
F05-1537-XX 1
B5A-1121-XX 1