Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Sankyo ICI3Q8-5293
- Page 1 Spec. No. Notes : ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ Revision Page Sym. Cha. No. Date Appr. Reference Document 2008.05.16 Design H.Takahashi AMO-NP-07533-01 ・ ・ Det-che NIDEC SANKYO CORPORATION Type Name ・ ・ Appro. No. S39Z-032-00-02D...
-
Page 2: Table Of Contents
AMO – NP – 15167 – 01 1 /11 -----Table of Contents----- Contents Page Before Use Important Notice Attentions to this instruction manual and cautions Scope Equipment summary and functions Unpacking Setup 7.1 How to connect 1) Power cable (Connector) 2) USB Cable 3) Power cable (Plug) Attention to the power supply... -
Page 3: Before Use
This operation manual is written for technical staff experienced in the general operation of magnetic and Non-contact IC card reader/encoders. It is intended to describe the operation of NIDEC Sankyo 's model ICI3Q8-5293. The terminal manufacturer shall be responsible to furnish an operation manual for end users. -
Page 4: Scope
3 /11 4. Scope This instruction manual is to describe proper handling procedures of the magnetic and Non-contact IC card reader/encoder, model number ICI3Q8-5293. 5. Equipment summary and functions Magnetic card reader/encoder, (hereafter referred to as MCRW), is a terminal with enclosure, and embedded power supply. - Page 5 AMO – NP – 15167 – 01 4 /11 ･POWER lamp: Lights when power is on. ･READY lamp: Lights or blinks as defined by operation and card processing status ･ERROR lamp: Lights or blinks when an error occurs. Cover screw Card gate Rear side Front side...
-
Page 6: Unpacking
AMO – NP – 15167 – 01 5 /11 6. Unpacking Included in the carton with the MCRW should be. Please inventory before proceeding. (1) MCRW 1 piece (2) Cables USB cable (SBE425501) 1 piece (to connect with Host computer) Power cable (SBE426401) 1 piece USB cable... -
Page 7: Usb Cable
AMO – NP – 15167 – 01 6 /11 2) USB Cable Ensure that the AC switch is off. Turn the MCRW over and insert the USB cable securely into the USB connector. Connect the other end to the appropriate USB port on the HOST. -
Page 8: How To Power On And Off
AMO – NP – 15167 – 01 7 /11 7.2 How to turn on and shut off the power supply: 1) How to turn on the power supply: Power on To power ON: press the " " on the AC switch. When the power is ON, the power LED on the front panel is lit. -
Page 9: How To Remove A Jammed Card
AMO – NP – 15167 – 01 8 /11 Fuse holder Fuse Insertion direction Fuse holder Insertion opening Fuse holder turn ditch Fuse rated T2.5A/250V How to remove a jammed card: Please refer to a trained technician for removal of a jammed card. When removing the jammed card, please follow the process below. - Page 10 AMO – NP – 15167 – 01 9 /11 AC Switch Upper case 5) Unhook the cover sheet from the top of the card reader and hold by the hook side. 6) Using tweezers, inserted from the top of the card reader, gently push the jammed card towards the gate until it can be easily removed by hand.
-
Page 11: Considerations For Card Handling
After cleaning the case should be wiped off with a dry cloth. 5) The magnetic head should be periodically cleaned. It is recommended that an approved cleaning card be used for this purpose. (Cleaning card :Sankyo P/N SBE018601) -
Page 12: Notes
AMO – NP – 15167 – 01 11 /11 10.Notes 1)FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Properly shielded a grounded cables and connectors must be used for connection to host computer and/or peripherals in order to meet FCC emission limits.