Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Zte Z723EL
Summary of Contents for Zte Z723EL
- Page 1 Z723EL User Guide...
-
Page 2: Table Of Contents
Status Indicator ............6 Device Installation ............ 8 Use Your Z723EL ..............8 Power On or Off ............8 Connect the Z723EL to a phone ....... 9 Placing and Ending Calls .......... 9 Adjusting Volume ............ 10 Checking Voicemail ..........11 Set Up a Conference Call ........ -
Page 3: Get Started
Get Started This chapter provides an overview of the Z723EL features. Know Your Device Your Z723EL enables you to make calls with your wireless service provider’s cellular network. 1. Voicemail 2. micro-USB jack (used for manufacturer) 3. Power 4. Information 5. -
Page 4: Interface Description
NOTE: Your Z723EL comes with the nano-SIM card inserted. Interface Description 1. Telephone ports: RJ11 connector for connection to telephone. 2. Power socket: Connector for the external power supply. 3. Power switch: Turn your device on or off. Install Your Battery... -
Page 5: Charge The Battery
Gently push down on the battery until it clicks into place. 3. Replace the back cover. Charge the Battery 1. Connect the adapter to the power socket of the Z723EL. Do not force the connector into the power socket. -
Page 6: Status Indicator
2. Connect the charger to a standard AC power outlet. 3. Disconnect the charger when the battery is fully charged. Status Indicator The indicator shows the device’s status: Indicator Status Description Green Power Green blinking Shutting down Power off Green Blinking New voicemail waiting Voicemail No message... - Page 7 blinking(10S) success Information Red blinking(10S) Update end fail Green blinking During activation Red blinking Activation fail Green More than 50% discharging Green blinking More than 50% charging Battery Charge Yellow 20%~49% discharging Yellow blinking 20%~49% charging Less than 20% discharging Red blinking Less than 20% charging No battery installed...
-
Page 8: Device Installation
The Z723EL works with your wireless service provider’s cellular network instead of your home’s phone jacks. Put the Z723EL in a place where there is a strong signal from a signal tower, typically near a window or outside wall. Use Your Z723EL This chapter describes how to make calls with Z723EL or configure the call settings. -
Page 9: Connect The Z723El To A Phone
2. Plug your phone into the ‘PHONE 1’ port on the device through a phone cable. NOTE: The “Phone 2” port can be used to connect an additional phone, or cordless base station. All telephones connected to the Z723EL will use the same telephone number. Placing and Ending Calls Place a Call by Dialing 1. -
Page 10: Adjusting Volume
Adjusting Volume You can adjust call volume using the volume controls of any connected phone or the Z723EL Volume Setting Mode. 1. When you are on a call, press ** or ## in 1 second to enter Volume Setting Mode. -
Page 11: Checking Voicemail
Your home phone(s) may have a separate volume level setting function that is independent of the Z723EL. Checking Voicemail You Z723EL support to divert calls to voicemail, callers can leave voicemail messages when they cannot reach you. The voicemail indicator on the Z723EL flashes when a voicemail message is waiting. - Page 12 NOTE: The call waiting and three-way call features need network support and may result in additional charges. Please contact your service provider for more information. 1. Place the first call. 2. Once you have established the connection, press the Flash (or Talk) key on your phone.
-
Page 13: Adjusting Your Call Settings
Adjusting Your Call Settings Set Voicemail 1. Dial *86 on any phone connected to your Z723EL and wait for 4 seconds to connect to your voicemail box. 2. Follow the system prompts to set your voicemail options, such as password and name announcement. -
Page 14: Tty Mode
Your Z723EL is a TTY compatible device. A TTY device can allow people who have hearing or speech disabilities to communicate by telephone. Select a TTY mode for your Z723EL to work with a TTY device, or turn TTY off. Dial *983*889*n# on your connected phone to set TTY mode. -
Page 15: Common Settings
Common Settings The following table lists common keyboard settings options for your Z723EL. Command Description *983*3284# Reset your device to factory mode. Set the auto-dialing time. *983*238*xx# "XX" means the time range: 4~12s.The default time is 4s. Set the flash diagnosing time. -
Page 16: Battery Specifications
Dimensions 1.11 x 6.30 x 5.51 in Weight Approx.383.5 g Interface Frequency 1.1G Technology Bands Supported Battery Specifications Item Description Limited Charge 4.35 V Voltage Type Lithium-ion Capacity 2300mAh Battery Talk Time Approx. 3 hours Continuous Standby Approx. 13 hours Time... -
Page 17: Troubleshooting
Symptoms Possible Problems/ Solutions There is no dial tone. Please wait for 1~2 minutes after the Z723EL is turned on. If signal reception is poor, move to where signal reception is good. The line is noisy/ distorted when I Remove any electrical ... -
Page 18: Regulatory And Safety Information
• Do not allow the Z723EL or accessories to come into contact with liquid or moisture at any time. Do not immerse the Z723EL in any liquid. • Do not place objects on top of the Z723EL. This may lead to overheating of the... -
Page 19: Cleaning And Maintaining
• The device must be placed in ventilation environment for use. • Do not expose the Z723EL to direct sunlight or store it in hot areas. High temperature can shorten the life of electronic devices. • Do not allow children to play with the Z723EL or charger. -
Page 20: Limited Warranty
End User shall have no right to reject or return the Product, or receive a refund for the Product from ZTE under the above-mentioned situations. • This warranty is End User’s sole remedy and ZTE’s sole liability for defective or nonconforming items, and is in lieu of all other warranties, expressed, implied... -
Page 21: Limitation Of Liability
Limitation of Liability ZTE shall not be liable for any loss of profits or indirect, special, incidental or consequential damages resulting from or arising out of or in connection with using of this product, whether or not ZTE had been advised, knew or should... - Page 22 may cause undesired operation. Caution: Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
- Page 23 • Consult the dealer or an experienced radio/TV technician for help. CTIA Requirements Do not disassemble or open crush, bend or deform, puncture or shred. Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water or other liquids, expose to fire, explosion or other hazard.
- Page 24 service center for inspection. Improper battery use may result in a fire, explosion or other hazard. The phone shall only be connected to CTIA certified adapters, products that bear the USB-IF logo or products that have completed the USB-IF compliance program WARNING: This product contains a chemical known to the State of California to cause...