Related Manuals for Locksys LSIV3501
Summary of Contents for Locksys LSIV3501
-
Page 1: User Manual
2.4GHz Digital Wireless Peephole Viewer User Manual Thanks for purchasing this product. Please carefully read this user manual before using the product and follow the manual to install and operate. -
Page 2: Table Of Contents
Contents 1. Introduction ................ 2 2. Features ................2 3. Packing list ................3 5. Indoor monitor ..............4 6. Installation instructions of peephole ........6 7. E-lock connection ..............7 8. Operation ................9 9. Specifications ..............14 10. Failure diagnosis ............... 15... -
Page 3: Introduction
1. Introduction The product is composed of peephole camera, peephole host, indoor monitor and wireless unlock control. You can operate the indoor monitor to communicate with visitors via voice and video, and then unlock the door if you wish. It’s applicable in apartment, hotel, office, building and so on. -
Page 4: Packing List
3. Packing list Outdoor part (Peephole part) (1) Peephole host (2) Camera of peephole (3) Screws and tape (4) Fixed board (5) BL-5J battery (6) Wireless unlock control (option) (7) Remote control (option) Indoor monitor part (8) 3.5” indoor monitor or 7” indoor monitor (9) Fixed iron for 7“ indoor monitor (10) BL-5J battery (11) USB Cable (12) USB power adapter, Input: 100-240V 50/60Hz Output: 5V/1A... -
Page 5: Indoor Monitor
4. Peephole (1) Motion detection sensor (2) Speaker (3) Infrared light (Red means turn on night vision, Blue means setting motion sensor work mode) (4) Camera lens (5) ‘Call’ button/motion sensor work mode selection (6) Microphone (7) Green light means paring, red light means low voltage (8) Green light means charging, red light means full charge. - Page 6 (B) 7” indoor Monitor (1) Speaker (2) TFT screen (3) Antenna (4) Microphone ‘Monitor’ button ’Unlock’ button (7) ’Talk’ button ▼ Left Down (10) Right (11) charging light ▲ ‘Take picture ’ button (14) (12) Working light (13) (15) USB interface (16) Power switch (17) Fixed slot (18) Battery lid (19) Bracket...
-
Page 7: Installation Instructions Of Peephole
6. Installation instructions of peephole Remark: Please make sure that the power switch is off or the battery is not inserted before installation. Flexible PCB is easily twisted and flectional, you should gently lift to avoid drape, nick, crunch caused by bump with other hard thing. -
Page 8: E-Lock Connection
board down and tighten the screws. Then connect the FPC with the CON1 of fixed board, for the redundant FPC, you can use the tape to paste and fix it. Notes: Not let the redundant FPC spread out of the fixed board. Step 4, Align the holes of the fixed board and the holes of peephole host, and then use 3 pieces of screws to fix them. - Page 9 Schematic diagram The wireless video peephole system can work together with intelligent lock, remote lock, Special remote control module will need to be embedded into the intelligent lock. Intelligent lock, remote lock uses 4pcs AA batteries.
-
Page 10: Operation
8. Operation Note: When the system is in working condition, if there is no blocking wall between indoor monitor and peephole, you must keep them above 6 meters apart to avoid ‘whistle’ sound. A Setting (1) Date and time When indoor monitor is in non-talk mode, press button for 3 seconds, there will be a "T"... - Page 11 (2) Melody and volume When indoor monitor is in non-talk mode, press button to select one of the 16 chord melodies as the sound. Press choose to the volume of melody (adjust level: 1-2). 16 chord melodies are Ding-dong, To Alice, Westminster bell, Butterfly lovers, The cygnet, Red river valley, My heart will go on, Turkey’s march, Small dance, Congratulations you, William's prelude, Love romance hudson, Memory, The Little Mermaid, Green sleeves, Romeo and Juliet.
- Page 12 (2) Talk, unlock Visitor presses “call” button of the peephole. All indoor monitors will sound melody. A. Press button of one indoor monitor to speak to visitor before unlock. If you want to let other indoor monitor to talk, press button to end the current dialogue, then another indoor monitor could press button to speak to visitor.
- Page 13 Press “Call” button of the camera of peephole for more than 6 seconds, the motion sensor work mode will be switched between on and off. If Infrared light firstly flash and then turn on, the motion sensor will start to work. If the Infrared light firstly flash and then turn off, the motion sensor will stop working.
- Page 14 one-to-multiple system. (1) 1V1 system is composed of one peephole and one indoor monitor Press ‘pair’ button of peephole, indicating light flash, press button of indoor monitor at the same time, the screen will show “ver. 1v1 paring’. If pairing succeeds, the video from peephole will be shown in the screen of indoor monitor.
-
Page 15: Specifications
Unlock control is connected to 12V power adapter. Firstly press the pair button of unlock control, pair light will flash once. Press the button of remote control, pair light will continuously flash. Once again press the pair button of unlock control, pair light will stop flashing. Finally press the button of remote control, the pair light will flash 3 seconds, it means that pairing is successful. -
Page 16: Failure Diagnosis
10. Failure diagnosis Defect Judgment Operation If turn the switch to the “on”? Indoor monitor or Turn the switch to the On peephole unable If the power of li-ion batteries is Charge the li-ion batteries to start not enough? If the plug of power adapter Re-connect the devices and correctly plug into USB power adapter...