Cino VersaJet MP3200 Series User Manual
Hide thumbs
Also See for VersaJet MP3200 Series:
- User manual (33 pages) ,
- Programming reference manual (196 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Cino VersaJet MP3200 Series
Summary of Contents for Cino VersaJet MP3200 Series
- Page 1 User’s Guide VersaJet Mobile Printer MP3200 Series...
-
Page 2: Regulatory Information
Trademarks All registered and unregistered trademarks used herein are the exclusive property of their respective owners. Copyright Copyright 1998-2005 PC Worth Int'l Co., Ltd. Copyright 1998-2005 Cino Group Regulatory Information FCC ID : SBCMP3200 15.21 You are cautioned that changes or modifications not expressly approved by the parts responsible for compliance could void the user’s authority to operate the equipment. -
Page 3: Table Of Contents
Table of Contents Getting Started Getting Familiar with MP3200 Series Installing and Charging the Battery Loading the Media Performing a Self -Test Print Operation Switch Functions LED Indicators Power Save Mode Auto Power Off Troubleshooting... -
Page 4: Getting Started
Getting Started Thank you for purchasing VersaJet MP3200 Series Mobile Printer. The MP3200 Series is designed with rugged yet lightweight architecture, delivering the ultimate convenience of mobility to meet your on-demanding labels and receipts printing requirement. IrDA, RS232 and Optional Bluetooth, communication... -
Page 5: Getting Familiar With Mp3200 Series
Getting familiar with MP3200 Please familiarize yourself with the features of your MP3200 Series as shown in the following diagram. -
Page 6: Installing And Charging The Battery
Installing and Charging the Battery One Battery Pack is included with the Printer and is shipped uncharged. Please unpack the Battery Pack prior to use. The Printer is powered by a 7.2V 2200mAH Li-Ion Battery Pack. Be sure to fully charge the new rechargeable Battery Pack before using it for the first time. - Page 7 Charging the Battery (1) Insert the charge cable into the printer charger jack, then plug the charger into the appropriate A.C. wall socket. (2) Power on the Printer by pressing the POWER switch. The LED 1 blinks green light five times, then turning to flash red light.
-
Page 8: Loading The Media
Loading the Media Deciding the Type of Media and Printing Mode Before loading the media, please decide the media type and printing mode. Note : If your desired media type is label, it’s necessary for you to change the printing mode by using the Printer Command. - Page 9 (2) Adjusting the Width Adjustment Spacer to one of the grooves in accordance with the width of the media roll. Grooves are available for the width from 34 to 58 mm with 3 mm per pitch. Confirm Direction Confirm Direction Width Adjustment Spacer (3) Set the media load as shown in the following diagram.
- Page 10 (5) Close the Media Compartment Cover. Note : By using label media with specific sensor setup, the Printer performs automatic Top-of-Form by feeding one label when closing the Media Compartment Cover under power-on status. But the Printer doesn’t perform Top-of-Form when using receipt media or continuous printing.
-
Page 11: Performing A Self-Test Print
Performing a Self-Test Print Printing a Configuration Message Printing a configuration message once the Battery Pack is fully charged and the media roll is loaded. Performing a Self-Test Print to verity the printer is under proper working condition. You can print a configuration message after conducting the Self-Test procedure. -
Page 12: Operation
Operation The tables below identify and define the Printer switches and LED indicators interface. Switch Functions The Printer has two control switches : POWER switch and FEED switch. Following table shows the Printer status by pressing each switch. under different states. Switch State Action... - Page 13 Normal Press, with Label Print Mode: Mode Media When no print has been Compartment done, feed one label. If Cover closed any print has been done, re-print the last label. Receipt Print Mode: Feed paper approx. 20mm. If follows “stop printing”...
-
Page 14: Led Indicators
LED Indicators The Printer has four LED Indicators. When you turn on the power or press the POWER switch under power save mode, the LED Indicators display the battery remains by blinking light. Please refer to the battery remains status by its LED light indication as shown below. -
Page 15: Power Save Mode
Power Save Mode To minimize the power consumption, the Printer changes to Power Save Mode in accordance with your setting automatically. If it’s under an error condition, then the Printer goes to power Saving Mode in 10 seconds. Power Save Mode can be terminated by performing following actions : Receiving data through IrDA (Link securing) Receiving data through RS232C... - Page 16 Pressing the Power switch The Printer carries out head check and displays battery remains, then turn to normal mode. 13 13...
-
Page 17: Auto Power Off
Auto Power Off In order to minimize the battery consumption, the Printer goes off automatically 10 minutes later after entering into Power Saving Mode. Before Auto Power-Off, MP3200 Series sends a notice to the last-communicated external equipment. If no response from the external equipment or no any operation on both POWER or FEED switches, the Printer will shut off in 10 seconds. -
Page 18: Troubleshooting
Troubleshooting Please review the following Troubleshooting Guide to solve common problems you may encounter with your Printer. If the problems are not covered in the Troubleshooting Guide, please contact the company where you purchased your Printer. If they can’t assist you, please contact PC World technical support at 886-2-2696-2559.
Need help?
Do you have a question about the VersaJet MP3200 Series and is the answer not in the manual?
Questions and answers