Bosch GBH 4-32 DFR Professional Original Instructions Manual page 10

OBJ_BUCH-411-008.book Page 10 Thursday, November 2, 2017 8:54 AM
10 | English
Dust Extraction with the Dust Extraction
Attachment (Accessory)
 Dust from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dust can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dust, such as oak or beech dust, is considered car-
cinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative). Materials con-
taining asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suitable
for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
 Prevent dust accumulation at the workplace. Dust can
easily ignite.
Mounting the Dust Extraction Attachment (see figure F)
For dust extraction, the dust extraction attachment (accesso-
ry) is required. When drilling, the dust extraction attachment
retracts so that the attachment head is always close to the
surface at the drill hole.
– Press the button for depth stop adjustment 9 and remove
the depth stop 11. Press button 9 again and insert the dust
extraction attachment into the auxiliary handle 10 from the
front.
– Connect an extraction hose (diameter 19 mm, accessory)
to the extraction sleeve 16 of the dust extraction attach-
ment.
The vacuum cleaner must be suitable for the material being
worked.
When vacuuming dry dust that is especially detrimental to
health or carcinogenic, use a special vacuum cleaner.
Adjusting the Drilling Depth on the Dust Extraction At-
tachment (see figure G)
The required drilling depth X can also be adjusted when the
dust extraction attachment is mounted.
– Insert the SDS-plus drilling tool to the stop into the SDS-
plus tool holder 1. Otherwise, the movability of the SDS-
plus drilling tool can lead to incorrect adjustment of the
drilling depth.
– Loosen the wing bolt 20 on the dust extraction attachment.
– Without switching the power tool on, apply it firmly to the
drilling location. The SDS-plus drilling tool must face
against the surface.
– Position the the guide pipe 21 of the dust extraction at-
tachment in its holding fixture in such a manner that the
head of the dust extraction attachment faces against the
surface to be drilled. Do not slide the guide pipe 21 further
over the telescopic pipe 19 of the dust extraction attach-
ment than required, so that as much as possible of the
scale 19 on the telescopic pipe remains visible.
– Retighten the wing bolt 20 again. Loosen the clamping
screw 17 on the depth stop of the dust extraction attach-
ment.
1 609 92A 40W | (2.11.17)
– Move the depth stop 18 on the telescopic pipe 19 in such
a manner that the clearance X shown in the figure corre-
sponds with the required drilling depth.
– Tighten the clamping screw 17 in this position.
Operation
Starting Operation
 Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Products sold in AUS and NZ only: Use a residual current de-
vice (RCD) with a rated residual current of 30 mA or less.
Setting the operating mode
The operating mode of the power tool is selected with the
mode selector switch 5.
Note: Change the operating mode only when the machine is
switched off! Otherwise, the machine can be damaged.
– Turn the mode selector switch 5 to the requested position.
Position for drilling without im-
pact in wood, metal, ceramic and
plastic as well as for screwdriving
Position for hammer drilling in
concrete or stone
When the drilling tool does not
immediately rotate upon switch-
ing on, allow the machine to run
slowly until the drilling tool ro-
tates.
Vario-Lock position for adjust-
ment of the chiselling position
Position for chiselling
Reversing the rotational direction
 Actuate the rotational direction switch 8 only when the
machine is at a standstill.
The rotational direction switch 8 is used to reverse the rota-
tional direction of the machine.
Right rotation: Turn the rotational direction switch 8 to the
stop in the position .
Left rotation: Turn the rotational direction switch 8 to the
stop in the position .
Set the direction of rotation for hammer drilling, drilling and
chiselling always to right rotation.
Bosch Power Tools