PRESIDENT Lincoln II + Owner's Manual page 10

- Rotate PUSH knob (6) to set desired CTCSS tone. There are 38 CTCSS tones
from 01 to 38.
- Continue to rotate PUSH knob (6) to
DCS codes from 001 to 104.
- Select "oFF" to clear
the memorized CTCSS tone or DCS code.
- Depending on the configuration of the menu [
12) press MEM-STORE key (5) for 2 seconds in order to:
In " " mode:
store
- the CTCSS tone or DCS code. The blinking stops.
In " " mode:
store
- the CTCSS tone or DCS code of the reception (RX).
- "TX" blinks in addition to the selected data.
- Rotate PUSH knob (6) to set desired CTCSS tone or DCS code of the transmis-
sion (TX).
- Press MEM-STORE key (5) for 2 seconds to store the CTCSS tone or DCS code
of the transmission (TX). The blinking stops.
- Long press MODE-CTCSS/DCS key (18) to
See tables on page 51.
19) VOX ~ VOX SET
VOX
(short press)
The VOX function allows transmitting by speaking into the original microphone
(or in the optional vox microphone) without pressing the PTT pedal (23). In
case of the use of an optional vox mike connected to the rear panel of the
radio - VOX MIC jack (E), the original microphone doesn't work.
Press the VOX key (19) in order to
on the LCD. A new pressure on the VOX key (19) switches the function off.
"VOX"disappears from the LCD.
VOX SET
(long press)
Press for 2 second the VOX-VOX SET key (19) in order to
function (if the VOX function is off, this will turn the function on and display
"VOX" on the LCD). " " appears on the LCD.
Three features are possible: Sensitivity level, Anti-Vox level and Vox Delay
time.
Press s/t keys (10) in order to select
feature.
Rotate PUSH (6) to set the feature.
store
Press MEM/STORE key (5) to
Once the adjustments are done, press the VOX-VOX SET key (19) in order
quit the VOX SET function. If any adjustment have been done during 5
to
set desired DCS code. There are 104
] (See § 17 page
disable CTCSS tone or DCS code.
activate the VOX function. "VOX" is displayed
activate the VOX SET
to the following feature. LCD shows the
skip
and into the next feature.
seconds, the transceiver will
- Sensitivity " ": allows the adjustment of the microphone (original one
or optional vox) for an optimum transmission quality. Adjustable level from 1
(high sensibility) to 9 (low sensibility). Default: 5.
- Anti-Vox " ": allows disabling the transmission generated by the surround-
ing noise. The level is adjustable: 0 (OFF), from1 (high level) to 9 (low level).
Default: 9.
- Delay Time " ": allows avoiding the sudden cut of the transmission by
adding a delay at the end of speaking. The level is adjustable from 1 (short
time delay) to 9 (long time delay). Default:1.
20) SPLIT ~ SPLIT SET
SPLIT
(short press)
The SPLIT function allows to transmit
Press SPLIT key (20) to enable
seconds.
Press SPLIT key again to disable
5 seconds.
Note: In mode, Channel, Band and Frequency are blinking if the SPLIT
TX
function is active.
SPLIT SET
(long press)
Long press SPLIT-SPLIT SET key (20) to set repeater's OFFSET and DIRECTION
alternate
Press s/t (10) to
the menu list.
Rotate PUSH (6) knob to set
Press MEM/STORE key (5) for 2 seconds to
Press SPLIT key (20) or wait for 5 seconds to
- FREQUENCY OFFSET: frequency blinks on the LCD.
- DIRECTION: LCD shows "SPLiT"."
rent channel, " " means negative offset set in current channel.
21) BAND ~ +10KHz
BAND
(short press)
Press BAND key (21) for quick movement
~ F ~ 9 ~ H ~ I~ J segments.
+10KHz
(long press)
Long press BAND-+10KHz key (21) to
"10K "
10
quit the VOX SET function automatically.
and receive on separated frequencies.
repeater function, LCD shows "
repeater function, LCD shows "
between FREQUENCY OFFSET and DIRECTION in
desired feature.
store and skip into next menu.
exit SPLIT SET function.
" in LCD means positive offset set in cur-
skipping 200 kHz in A ~ B ~ C ~ D ~ E
enable frequency +10KHZ. LCD shows
" for 5
" for