Table of Contents
Advertisement
Mareli Systems
PS 24 Pellet stove
Assembly and exploitation manual
The present stove is designed and manufactured according to
Standards: BNS (Bulgarian National Standard) EN 14785-2006
Advertisement
Table of Contents
Related Manuals for Mareli Systems PS 24
Summary of Contents for Mareli Systems PS 24
- Page 1 Mareli Systems PS 24 Pellet stove Assembly and exploitation manual The present stove is designed and manufactured according to Standards: BNS (Bulgarian National Standard) EN 14785-2006...
- Page 2 Mareli Systems Observing the prescriptions of the present manual is in the user’s favour and is one of the war- ranty conditions. Compliance with this instruction is in the interest of the consumer and one of the warranty terms. NSTRUCTIONS FOR SECURITY: •...
- Page 3 Mareli Systems 1. PURPOSE The stove is purposed to heat domestic and public premises by the means of pellets. The stove is equipped with a steel water jacket designed for heating systems with water temperature up to 90º C at a maximum super pressure up to 0,15 Mpa. Tests are run at pressure of 0,3 Mpa.
- Page 4 Mareli Systems 2. TECHNICAL DATA 3. ASSEMBLY 3.1 General conditions. For ensuring the proper and safe work of the stove the observation of the following prescriptions is required: The assembly of the stove and the related equipment must be performed by authorized personnel only.
- Page 5 0,3 litr on a single start-up. The accumulating char reduces the temperature difference and the condensation. • “Mareli Systems” provides a warranty and out of warranty service and replacement of the water jackets. • The warranty is not valid in case of a stove with a swollen water jacket which is a result of pressure increase in the system and improper connecting.
- Page 6 Mareli Systems 3.3 Assembly of the duct components. Duct components and pipes For the assembly of the duct pipes the use of non-flammable materials, resistant to the flammable products and condensation is obligatory. The assembly must be performed in such a manner so it guarantees the airtight sealing and prevents condensation.
- Page 7 Mareli Systems 3.5 Air intake Suction pipe or air intake is placed in the back and has a cir- cular section with a diameter of 48 mm. The combustion air can be aspirated: • From the camera, as long as it is near an air intake com-...
- Page 8 Mareli Systems 5 Safety and unexpected risks Terms of danger may arise in the following cases: • Automated pellet stove is used incorrectly; • The unit is installed by unqualified personnel; • The safety instructions described in this management are not met;...
- Page 9 Mareli Systems CONTROL PANEL: USE AND FUNCTIONS The main frame shows: time and date, chrono activation, combustion power and recipe, functioning state, error code, main temperature, main thermostat, summer/winter mode. Button Function Exit Menu/Submenu; Ignition and extinguishing (push for 3 seconds), Reset errors (push for 3 seconds), Enable/disable chrono;...
- Page 10 Mareli Systems MESSAGES Description Code Sond Anomaly of the probes checking, during Check Up phase. Room temperature greater than 99 °C. Clean This message noti es that the planned hours of functioning are reached. Port Door Open. Ignition The message appears if the system is turned o during Ignition (after Preload) not manually: the system will stop only when it goes in Run Mode.
- Page 11 Mareli Systems CHRONO This Manu allows selecting the programming modalities and and the Ignition/Extinguishing time slots. Modality - It allows selecting the disired modality, or disable all set programming. Disable 1. Enter modi cation mode through the key P3. Daily 2.
- Page 12 Mareli Systems FIRST CONFIGURATION First select the plumbing installation (parameter from the Enable menu of the Technical menu).
- Page 13 Mareli Systems...
- Page 14 Mareli Systems...
- Page 15 Mareli Systems...
- Page 16 MARELI SYSTEMS disclaims any responsibility for possible inaccuracies contained in this manu- al if they are due to printing or transcription errors. We reserve the right to make any change that appears to be necessary or useful without harm the essential characteristics.