Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Voyager WVOS7MDCL1Q
Summary of Contents for Voyager WVOS7MDCL1Q
- Page 1 TOUGH CAM Version 1.0 Model: WVOS7MDCL1Q PLEASE READ CAREFULLY AND SAVE This manual contains important information about this product’s operation. If you are installing this product for others, you must have this manual – or a copy – with the end user.
- Page 2 INTRODUCTION KEY FEATURES: • The ToughCam supports up to 200 meter of Secured video transmissions • The 7” LCD wireless monitor supports up to VGA@25FPS (Single Camera); or QVGA@20fps (Multiple Camera) • Expandable up to 4 camera connection. • Wireless monitor support CH auto-switch functions, with a signal trigger cable connect from the monitor to the power switch of the rear-gear warning light;...
- Page 3 FCC Compliance Statement: This Products with CE Marking comply with device complies with Part 15 of the EMC Directive (2004/108/EC); Low FCC rules. Operation is subjected Voltage Directive (73/23/EEC); to the following two conditions: (1) R&TTE(1999/5/EC); ROHS Directive this device may not cause harmful interference, (2011/65/EU) issued by the Commission of the and (2) this device must accept any interference European Community.
-
Page 4: Kit Content
KIT CONTENT Image Contents Wireless video camera with mounting bracket 1 EA 5dBi antennas 2 EA 9.5 ft. cable and mounting bracket 2 EA Wireless 7” LCD monitor 1 EA Monitor mount 1 EA Remote control for the monitor 1 EA Cigarette adaptor for the monitor 1 EA Hardwire cable for monitor... -
Page 5: Installing The Camera
INSTALLING THE CAMERA With fixed power source 1. Choose a place at rear bumper you wish to install (usually, in the middle of bumper). 2. Screw the camera’s mounting bracket on the bumper. Make sure the camera’s firmly fitted. 3. Connect the power cable with horseshoe joints to the power source (12- 24V). Connect the red cable to the positive pole and the black cable to the negative pole. -
Page 6: Using The Trigger Cable
Note: The camera will be automatically turned on in Channel 1 when the vehicle is in reverse condition. 5. Turn on the monitor. The screen should show the image transmitted from the camera automatically. If it doesn’t, please refer to the Pairing Camera(s) section to pair the camera with the monitor. -
Page 7: Installing The Monitor
INSTALLING THE MONITOR Screw the antenna on the antenna connector. Secure stand base to stand with provided screws. Fix the mounting metal panel to the back panel of monitor. Secure stand to mounting metal panel, adjust proper view angle, and secure the joint with T-bolt. - Page 8 Choose a place in car you wish to stick, and fix the monitor with provided twin adhesive in the package. Connect the cigarette adaptor to the DC power jack of the LCD monitor. Plug the power unit to the cigarette power source beside the driver’s seat and turn on the ignition and press the Power button to turn on the monitor.
-
Page 9: Getting To Know Your Camera
GETTING TO KNOW YOUR CAMERA 1. Camera Lens 6. Antenna 2. Pairing Key 7. Power cord to the vehicle back light 3. Mounting Bracket 8. Link LED Indicator 4. IR LEDs 9. Power LED Indicator 5. EDS... -
Page 10: Getting To Know Your Receiver
GETTING TO KNOW YOUR RECEIVER Antenna Socket Link Indicator Power Button Power Indicator Trigger Cable Power Adaptor ... -
Page 11: Monitor Function Buttons
Monitor Function Buttons Monitor Button Function Remote Controller (Menu Mode) [Cursor Up] / (QUAD View Mode) [Hot key CH1] (Menu Mode) [Cursor Right] / (QUAD View Mode) [Hot key CH2] (Menu Mode) [Cursor DOWN] / (QUAD View Mode) [Hot key CH3] (Menu Mode) [Cursor Left] / (QUAD View Mode) [Hot key CH4] (Menu Mode) [Menu / Enter Button]... -
Page 12: Configuring Your Receiver
CONFIGURING YOUR RECEIVER Press the Power button to power ON the monitor. Press and hold to power OFF the monitor. Press (MENU button) to enter/exit the Main menu. Use the (Left / Right / Up / Down) buttons to navigate through menu items and change the settings. -
Page 13: Pairing Camera(S)
Pairing camera(s) When you install an extra camera or if the monitor doesn’t detect it, please use this feature to pair the camera with the monitor. IMPORTANT: Before pairing the camera, make sure camera power cord is well connected to a constant 12-24V DC power source. -
Page 14: Monitor And Camera Version
4. Once pairing completed, the monitor will display the camera image immediately. Brightness Set up the brightness of the cameras for different environment. Each camera can be configured individually. 1. Press (MENU button) and to choose the Brightness function 2. Press (MENU button) to enter the sub menu 3. -
Page 15: Factory Reset
Factory Reset Restore the monitor to the factory default settings. 1. Press (MENU button) and to choose the Factory option. 2. Press (MENU button) to restore the default settings as below. Scan CAM1 CAM2 CAM3 CAM4 Pair CAM 1 2 3 4 Brightness Monitor CAM1... - Page 16 channel will be displayed as blank screen. To leave QUAD display, please press (Left / Right / Up / Down) to go to the specified channel. IMPORTANT: 1. This function is available for multi cameras user. Before setting QUAD display, make sure all cameras are paired to assigned channels.
-
Page 17: Troubleshooting
TROUBLE SHOOTING This section offers some helpful information to overcome most of the problems you may encounter. We hope this section can help you to enjoy a pleasant setup. Problem Possible Causes Remedies System Message shows No power supply to Check back light, make “NO Signal”... -
Page 18: Product Specification
PRODUCT SPECIFICATION Camera Type: CMOS1/4 Image Sensor Resolution: 640*480 Lens Type: Glass Lens Focal Length: 2.5MM Optical View Angle: Horizontal:87°±2°; Vertical:62°±2° Resolution (TV Line): 480*272 Total IR LED: 10 PCS LED Angle: Night Vision LED Wave Length: 850nm EDS Activate LUX: 1-8LUX Identified Range: 5-8m... - Page 21 FCC NOTE： This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS OR CHANGE TO THIS EQUIPMENT.