Advertisement
Quick Links
MANUAL ENGLISH
PRODUCT DESCRIPTION
IMPORTANT!
In order to get the best out of your system it is important you take
the time to read through the manual before you start to
install/program your equipment.
The system (EF-7700) consists out of two parts: the transmitter
(EF-7602) and the receiver including wiring (EF-7701).
The transmitter and receiver are preset and factory coded. This
means that the system is ready for use. Every transmitter has a
fixed, unique serial coding which has been programmed into the
receiver, so that another transmitter cannot control the receiver.
APPLICATIONS
The receivers and transmitters of the System EF-7700 are pre-
programmed. They are meant to control fixed or mobile equipment
with a limited amount of functions.
SAFETY
Ensure that:
Appropriate personnel receive a review of the systems'
functions before it is used.
Only appropriate personnel have access to the
transmitter.
The transmitter is not left unsupervised.
The operator always has a complete view of the
equipment when it is radio controlled.
Be sure that your hydraulic lift application is shut off
during transit.
CAUTION: tampering with the product, changing the settings
or using the product in a fashion other than as set forth
herein can lead to product malfunctions which in turn can
lead to serious injuries or death. Any tampering,
unauthorized change in the product, misuse or abuse will
invalidate SPX's warranty on the product.
Rev 1 date 26-04-11 RS
1-8
Advertisement
Summary of Contents for SPX EF-7700
- Page 1 The system (EF-7700) consists out of two parts: the transmitter (EF-7602) and the receiver including wiring (EF-7701). The transmitter and receiver are preset and factory coded. This means that the system is ready for use.
- Page 2 MANUAL ENGLISH RECEIVER EF-7701 Operating voltage: 12-30 V AC/DC Power consumption: 30-80 mA Dimensions: 54 x 96 x 37 mm Protection: IP 65 Climatic conditions: -30°C to +70°C Humidity: 10%-90% Compatible transmitter: EF-7702 1. Yellow LED Lights up when the receiver has the correct operating voltage.
- Page 3 MANUAL ENGLISH TRANSMITTER EF-7702 FUNCTION The transmitter must be activated by pushing the ON/OFF button for 3 seconds. After that the UP or DOWN button can be used for operating the system. The transmitter is active when the LED glows steadily. Note: if the transmitter is not used within 60 seconds, it turns off automatically.
-
Page 4: Assembly And Installation
MANUAL ENGLISH PREPARATIONS ASSEMBLY AND INSTALLATION Select a suitable location for assembly of the receiver. Connect the Positive (+). (BLACK 2) Connect the ground cable of the receiver (YELL/GR) Connect the first coil (BLACK 3) The black cable (4) is to connect a second coil when using a 3P/4W valve. -
Page 5: Placement Of The Receiver
MANUAL ENGLISH PLACEMENT OF THE RECEIVER - Select a location, if possible, that is protected from the wind and weather. Place it with cable-glands facing downward. Avoid locations where the receiver may be exposed to abnormal moisture conditions, e.g. during high pressure washing. -
Page 6: Troubleshooting
MANUAL ENGLISH 2. Push the teach-in button on the receiver until the red LED lights up. 3. Release the button when the red LED light up. 4. Turn transmitter ON. 5. Push on any button of the transmitter that is to be used with the receiver. - Page 7 MANUAL ENGLISH PROBLEM POSSIBLE CAUSE SOLUTION The YELLOW LED The receiver is not Check the of the receiver does well connected to connection of the not light up. the power supply. power supply. Incorrect power Check the power voltage supply. voltage supply.
- Page 8 MANUAL ENGLISH RECYCLING, SCRAPPING EF-7700-systems and any accessories and spare parts no longer in use should be scrapped and recycled according to local environmental regulations. Rev 1 date 26-04-11 RS...