1. Precautions and Safety Notices 1.1 Appropriate Operation (1) Turn off the product before cleaning. (2) Use only a dry soft cloth when cleaning the LCD panel surface. (3) Use a soft cloth soaked with mild detergent to clean the display housing. (4) Use only a high quality, safety approved AC/DC power cord.
Page 5
ordinances or regulations for disposal. (13) The LCD module contains a small amount of materials having no flammability grade. The LCD module should be supplied with power that complies with the requirements of Limited Power Source (IEC60950 or UL1950), or an exemption should be applied for. (14) The LCD module is designed so that the CCFL in it is supplied by a Limited Current Circuit (IEC60950 or UL1950).
Page 6
Correct Methods Incorrect Methods Only touch the metal-frame of the panel or the front Surface of the panel is pressed by fingers and that may cause “ MURA “ cover of the monitor. Do not touch the surface of the polarizer. Take out the monitor from carton.
Portuguese, Russian, Turkish , French, Czech, ViewSonic CD Wizard Hungarian, Simplified Chinese, Traditional Chinese Greek, Dutch, Bulgarian, Croatian, Romanian, Serbian, Slovak, Slovenian ViewSonic Quick Start Guide One Page Perfect Suite CD Screen Protector Mylar Foot Protector plastic Base assembly Procedure Card...
Page 8
2.2 Interface description Video Connector Pin Assignment A -1.15 pin D-sub connector pin assignment Pin Number Pin Function Red video input Green video input Blue video input No Connection Ground Red video ground Green video ground Blue video ground H/V sync ground No connection (SDA) Horizontal sync (Composite sync)
3. Front Panel Function Control Description “Main Menu Controls” Main Menu with OSD controls Front Control Panel shown below in detail Power light Displays the control screen Blue = ON for the highlighted control. Orange = Power Saving Also toggles between two controls on some screens.
Page 10
Do the following to adjust the display setting: 1. To display the Main Menu, press button [1]. NOTE: All OSD menus and adjustment screens disappear automatically after about 15 seconds. This is adjustable through the OSD timeout setting in the setup menu. 2.
Main Menu Controls Adjust the menu items shown below by using the up and down buttons. Control Explanation Auto Image Adjust automatically sizes, centers, and fine tunes the video signal Auto eliminate waviness and distortion. Press the [2] button to obtain a sharper image.
Page 12
Information displays the timing mode (video signal input) coming from the graphics card in the computer, the LCD model number, the serial number, and the ViewSonic® website URL. See your graphics card’s user guide for instructions on changing the resolution and refresh rate (vertical frequency).
Page 13
Control Explanation Sharpness adjusts the clarity and focus of the screen image. Aspect ratio Selects the image size for 4:3 and full screen. ECO Mode provides the lower power consumption by reducing the brightness. Standard: The default brightness setting Optimize: Decreases the brightness by 25 % Conserve: Decreases the brightness by 50 % NOTE: When the ECO Mode is set to "Optimize"...
4. Circuit Description The RTD2533V(H) is total solution graphics processing IC for LCD monitors with panel resolutions up to WXGA. It is configured with a high-speed integrated triple-ADC/PLL, an integrated DVI receiver, a high quality display processing engine, and an integrated output display interface that can support RSDS panel interface format. To further reduce system costs, the RTD2533V(H) also integrates intelligent power management control capability and spread- spectrum support for EMI management.
Page 15
5. Adjustment Procedure 1. All Modes Reset You should do “All Model Reset” (Refer to Chap 3. Hot Keys for Function Controls) first. This action will allow you to erase all end-user’s settings and restore the factory defaults. 2. Auto Image Adjust The Auto Adjust is aimed to offer a best screen quality by built-in ASIC.
Page 16
7. 25 Gray Test Signal: 1280*1024@60Hz Test Pattern: Full Screen 25% White (Gray) Inspection Item: Particle, Line Defect & Mura 8. 50 Gray Test Signal: 1280*1024@60Hz Test Pattern: Full Screen 50% White (Gray) Inspection Item: Bright Dot, Particle, Line Defect & Mura 9.
Page 17
12. Green Test Signal: 1280*1024@60Hz Test Pattern: Full Screen Green Inspection Item: Bright Dot, Partial & Line Defect 13. Blue Test Signal: 1280*1024@60Hz Test Pattern: Full Screen Green Inspection Item: Bright Dot, Partial & Line Defect 14. Gray_Scale_0-100_V64 Test Signal: 1280*1024@60Hz Test Pattern: Vertical 64 (256) Gray Scale (Right →...
Page 19
Figure 7 Figure 8 RTD2120 ISP user flow Software : RTD ISP Ver3.0 Hardware : Print to D-Sub and DVI-D Converter Step 1. Update BIOS Flow: Execute ISP.exe...
Page 20
Step2. Click【64K】, Select the first file name xxxxxxxxxx_1.hex and Click【64~96】, Select the second file name xxxxxxxx_2.hex Step 3. Select【Both】and 【Auto】.
Page 21
Step 4. Click then appear below condition.
Loose or broken pins in the cable connector could cause an improper connection. • Connect the LCD display to another computer. • If you have an older graphics card, contact ViewSonic® for a non-DDC adapter Control buttons do not work • Press only one button at a time.
Page 25
Main board GND _POWER R I+ OPEN/U DZSF-5.6B/RoHS к75稼﹊ OPEN /BAV99/RoH S Trace舼篶疭┦ VGA_SDA GN D_POW ER VGA_SD A H SIN OPEN/0402/100n/16V/Y VSIN VGA_SC L VGA_SC L GN D_POW ER CN 1 MLX89263-6762/R oHS OPEN/U DZSF-5.6B/RoH S OPEN/U DZSF-5.6B/RoHS GN D _POWER OPEN /UD ZSF-5.6B/R oH S GN D_POWER к75稼﹊...
Page 49
N34G0082 ZK 1B CM STAND_BACK 40-D018271 0Q1G 330 10120 SCREW FOR FP/RC 42-D003792 N34G0083 ZK 1B CM STAND_HOLDER 40-D018273 N12G6300003 RUBBER_CAP 40-D000227 N34G0161 NB 1B FJ REAR 40-D020283 N23G3155709 1A VIEWSONIC NAME PLATE 77-D000224 N23G3178712 1A VSC-BIRD-LOGO 77-D020778 N34G0084 ZK 1B REAR 40-D018839...
Page 50
089G1748GAA AC SIGNAL CABLE DVI GREATLAND 089G 728GAA DB D-SUB CABLE 089G414A18N IS POWER CORD 32E1818021 089G414A18N YH POWER CORD(32E1818021) N40G000196868A S/N LABEL N40G000296813B ZA QC PASS LABEL N40G000296821A ZA Supplier label N40G000296811C ZA Customer label on Carton 052G 1211 A Conductive Tape 55mm *45mm *0.08mm N52G 1211021 HB...
Page 51
067G305V101 4P CAP 105C 100UF M 25V 6.3*11 033G801936Y H HC 0.5 PITCH 36P SMT FPC CONN 033G801936Y H HC 0.5 PITCH 36P SMT FPC CONN 056G 562578CMO IC,Scaler,RTD2554VH-GR,QFP-128 056G 563 52 IC AP1117D33L-13 TO252-3L DIODES 056G 563 52 IC AP1117D33L-13 TO252-3L DIODES 056G 563113 IC G1117-18T63Uf 1A/1.8V SOT-223 056G1125701 X...
Page 67
065G0402104 17 CAP CHIP 0402 100nF Z 16V Y5V 065G0402104 17 CAP CHIP 0402 100nF Z 16V Y5V 065G0402104 17 CAP CHIP 0402 100nF Z 16V Y5V 065G0402104 17 CAP CHIP 0402 100nF Z 16V Y5V 065G0402104 17 CAP CHIP 0402 100nF Z 16V Y5V 065G0402104 17 CAP CHIP 0402 100nF Z 16V Y5V 065G0402104 17...
Page 68
N85G0007 1 COVER AD 41-D021311 N52G 2191 01 TAPE /7345911004 N52G 1VSC002 HY Security Tape- 7345511002 N40G000196867A S/N LABEL FOR VIEWSONIC N40G0001968 2A S/N LABEL 7741513161 N44G9003185 CORNER PAPER 7841595111/78-D004862 N44G9003 80 CORNER PAPER 78-D004868 N07G0004 1 PALLET 78-D003113...
Page 69
SCREW FOR FP/RC 42-D003792 N34G0083 ZK 1B CM STAND_HOLDER 40-D018273 N12G6300003 RUBBER_CAP 40-D000227 N34G0161 NB 1B FJ REAR 40-D020283 N23G3155709 1A VIEWSONIC NAME PLATE 77-D000224 N23G3178712 1A VSC-BIRD-LOGO 77-D020778 N34G0084 ZK 1B REAR 40-D018839 052G 1207 A Conductive Tape 45mm *25mm *0.08mm...
Page 70
089G 728GAA DB D-SUB CABLE 080G L19 6HIC POWER BOARD 089G176W 15502 FFC (Keypad) 089G1748GAA AC SIGNAL CABLE DVI GREATLAND 089G176J 36N00 FFC CABLE 36P 103MM/32-D011012 705GN834406 Bezel Ass'y40-D021374 705GN834408 BEZEL ASS'Y 40-D021372 089G412A18NIS3 POWER CORD/32E1818058 089G404A18N YH POWER CORD(32E1818018/32-D022217) 089G421A18N IS POWER CORD/32-D022217 N34G0162 NB 1B FJ...
POWER CORD(32-D022438)(美規) POWER CORD/32E1818058(与 TPV 共用) 089G412A18NIS3 089G404A18N YH POWER CORD(32E1818018/32-D022217) POWER CORD/32-D022217(与 TPV 共用) 089G421A18N IS N40G000196867A S/N LABEL FOR VIEWSONIC Diversity of T96MRADKIWVSNNN compared with T96MRADDIWVSNND Location Part No. Description Remark POWER CORD/(TPV 共用)32-D022438 089G402A18N IS 089G402A18N YH POWER CORD(32-D022438)(美規)
Page 76
Reader’s basic dada: Name: Title: Company: Add: Tel: Fax: E-mail: After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile 1-909-839-7943. You may also e-mail any suggestions to the Director, Quality Systems & Processes (marc.maupin@viewsonic.com)
Need help?
Do you have a question about the VS11755 and is the answer not in the manual?
Questions and answers