LED Moving Head 120W SPOT MK2 F7100079 Table of Contents Introduction ..............................2 Safety information ............................2 General information ........................... 2 AC Power ..............................2 Specification ..............................3 Installation ................................ 3 Connections ..............................4 Connecting DMX signal..........................4 Fixture linking ............................4 Master/Slave fixture linking ........................
INTRODUCTION Thank you for purchasing LED Moving Head 120W SPOT MK2. For safety reasons and to ensure the trouble- free operation, carefully read the instructions. SAFETY INFORMATION General information Installation should be done by qualified personnel in order to minimize the risk of accidental electric shock.
LED Moving Head 120W SPOT MK2 F7100079 WARNING! Verify that the voltage select switch on your unit matches the line voltage applied. Damage to your fixture may result if the line voltage applied does not match the voltage indicated on the voltage selector switch.
Ensure proper connection to the mains and proper grounding. Make sure that the electrical parameters are consistent with device requirements. All activities, including connecting the device to the mains must be performed by qualified personnel. This fixture may be mounted in any position provided there is adequate room for ventilation. CONNECTIONS The device is equipped with the following interfaces: DMX (in/out): XLR 3-pin socket...
LED Moving Head 120W SPOT MK2 F7100079 CAUTION: At the last fixture, the DMX signal has to be terminated with a terminator. Solder a 120 8486 resistor between signal (-) and signal (+) into a XLR plug and plug it in the DMX output of the last fixture.
MENU DMX Address Set DMX address / DMX mode ON Alone Inside Program Master Auto Play Alone Music Control Master Slave Control Reset ON / OFF Pan Reverse ON / OFF TiltReverse ON / OFF Mic Sensitivity 0-100% Reset Default ON / OFF Calibration Code...
LED Moving Head 120W SPOT MK2 F7100079 DMX CHANNEL LIST 16CH mode Channel Function Effect CH 1 0-255: 0°-630° Pan Fine CH 2 0-255: Fine adjustment Tilt CH 3 0-255: 0°-230° Tilt Fine CH 4 0-255: Fine adjustment 0-14: White...
WPROWADZENIE Dziękujemy za zakup urządzenia Głowica ruchoma LED 120W SPOT MK2. Ze względów bezpieczeństwa oraz w celu zapewnienia bezawaryjnej pracy urządzenia należy dokładnie zapoznać się z instrukcją. BEZPIECZEŃSTWO Informacje o bezpieczeństwie Instalacja powinna być przeprowadzana przez wykwalifikowany personel, aby zminimalizować ryzyko przypadkowego porażenia prądem Przed instalacją...
LED Moving Head 120W SPOT MK2 F7100079 Zasilanie Wymagania energetyczne dla urządzenia można znaleźć na naklejce umieszczonej na tylnej płycie lub w specyfikacji zasilania. Pobór prądu określony w specyfikacji jest to średni pobór prądu w normalnych warunkach. Wszystkie urządzenia muszą być podłączone bezpośrednio do obwodu zasilającego i nie mogą...
INSTALACJA Po usunięciu opakowania należy sprawdzić, czy urządzenie nie zostało uszkodzone podczas transportu. Przed podłączeniem do sieci, upewnij się, że urządzenie jest prawidłowo zamontowane. Producent nie ponosi odpowiedzialności za szkody spowodowane niewłaściwym montażem. Należy zapewnić prawidłowe podłączenie do zasilania i uziemienia. Upewnij się, że parametry elektryczne są...
LED Moving Head 120W SPOT MK2 F7100079 Urządzenia należy połączyć szeregowo aby uruchomić pokaz świetlny wykorzystując kontroler DMX-512 lub aby uruchomić odpowiedni pokaz na dwóch lub więcej urządzeniach zsynchronizowanych w trybie pracy master/slave. Łączna liczba kanałów wymaganych przez wszystkie urządzenia określa liczbę lamp która może być...
MENU DMX Address Ustawienie adresu DMX / włączenie trybu DMX Alone Inside Program Master Auto Play Alone Music Control Master Slave Control Reset ON / OFF Pan Reverse ON / OFF TiltReverse ON / OFF Mic Sensitivity 0-100% Reset Default ON / OFF Calibration Code...