Yamaha S03 Service Manual page 48

S03
<Table 1 - 5>
MIDI Parameter Change table (MULTI PART)
Address Size Data Parameter
(H) (H) (H)
08 nn 00 1 00 - 20 ELEMENT RESERVE
01 1 00 - 7F BANK SELECT MSB
02 1 00 - 7F BANK SELECT LSB
03 1 00 - 7F PROGRAM NUMBER
04 1 00-0F, 7F Rcv CHANNEL
05 1 00 - 01 MONO/POLY MODE
06 1 00 - 02 SAME NOTE NUMBER
KEY ON ASSIGN
07 1 00 - 03 PART MODE
08 1 28 - 58 NOTE SHIFT
09 2 00 - 0F DETUNE
0A 00 - 0F
0B 1 00 - 7F VOLUME
0C 1 00 - 7F VELOCITY SENSE DEPTH
0D 1 00 - 7F VELOCITY SENSE OFFSET
0E 1 00 - 7F PAN
0F 1 00 - 7F NOTE LIMIT LOW
10 1 00 - 7F NOTE LIMIT HIGH
11 1 00 - 7F DRY LEVEL
12 1 00 - 7F CHORUS SEND
13 1 00 - 7F REVERB SEND
14 1 00 - 7F VARIATION SEND
15 1 00 - 7F VIBRATO RATE
16 1 00 - 7F VIBRATO DEPTH
17 1 00 - 7F VIBRATO DELAY
LOW PASS FILTER
18 1 00 - 7F
CUTOFF FREQUENCY
LOW PASS FILTER
19 1 00 - 7F
RESONANCE
1A 1 00 - 7F EG ATTACK TIME
1B 1 00 - 7F EG DECAY TIME
1C 1 00 - 7F EG RELEASE TIME
1D 1 28 - 58 MW PITCH CONTROL
MW LOW PASS FILTER
1E 1 00 - 7F
CONTROL
1F 1 00 - 7F MW AMPLITUDE CONTROL
20 1 00 - 7F MW LFO PMOD DEPTH
21 1 00 - 7F MW LFO FMOD DEPTH
22 1 00 - 7F MW LFO AMOD DEPTH
23 1 28 - 58 BEND PITCH CONTROL
BEND LOWPASS FILTER
24 1 00 - 7F
CONTROL
25 1 00 - 7F BEND AMPLITUDE CONTROL
26 1 00 - 7F BEND LFO PMOD DEPTH
27 1 00 - 7F BEND LFO FMOD DEPTH
28 1 00 - 7F BEND LFO AMOD DEPTH
TOTAL SIZE 29
08 nn 30 1 00 - 01 Rcv PITCH BEND
31 1 00 - 01 Rcv CH AFTER TOUCH(CAT)
32 1 00 - 01 Rcv PROGRAM CHANGE
33 1 00 - 01 Rcv CONTROL CHANGE
34 1 00 - 01 Rcv POLY AFTER TOUCH(PAT)
35 1 00 - 01 Rcv NOTE MESSAGE
36 1 00 - 01 Rcv RPN
37 1 00 - 01 Rcv NRPN
38 1 00 - 01 Rcv MODURATION
39 1 00 - 01 Rcv VOLUME
3A 1 00 - 01 Rcv PAN
3B 1 00 - 01 Rcv EXPRESSION
3C 1 00 - 01 Rcv HOLD1
3D 1 00 - 01 Rcv PORTAMENTO
3E 1 00 - 01 Rcv SOSTENUTO
3F 1 00 - 01 Rcv SOFT PEDAL
40 1 00 - 01 Rcv BANK SELECT
41 1 00 - 7F SCALE TUNING C
42 1 00 - 7F SCALE TUNING C#
43 1 00 - 7F SCALE TUNING D
44 1 00 - 7F SCALE TUNING D#
45 1 00 - 7F SCALE TUNING E
46 1 00 - 7F SCALE TUNING F
47 1 00 - 7F SCALE TUNING F#
48 1 00 - 7F SCALE TUNING G
49 1 00 - 7F SCALE TUNING G#
4A 1 00 - 7F SCALE TUNING A
4B 1 00 - 7F SCALE TUNING A#
4C 1 00 - 7F SCALE TUNING B
4D 1 28 - 58 CAT PITCH CONTROL
CAT LOW PASS FILTER
4E 1 00 - 7F
CONTROL
4F 1 00 - 7F CAT AMPLITUDE CONTROL
50 1 00 - 7F CAT LFO PMOD DEPTH
51 1 00 - 7F CAT LFO FMOD DEPTH
52 1 00 - 7F CAT LFO AMOD DEPTH
53 1 28 - 58 PAT PITCH CONTROL
PAT LOW PASS FILTER
54 1 00 - 7F
CONTROL
55 1 00 - 7F PAT AMPLITUDE CONTROL
56 1 00 - 7F PAT LFO PMOD DEPTH
57 1 00 - 7F PAT LFO FMOD DEPTH
58 1 00 - 7F PAT LFO AMOD DEPTH
59 1 00 - 5F AC1 CONTROLLER NUMBER
5A 1 28 - 58 AC1 PITCH CONTROL
AC1 LOW PASS FILTER
5B 1 00 - 7F
CONTROL
5C 1 00 - 7F AC1 AMPLITUDE CONTROL
48
Description Default value
(H)
0...64 part10 = 0
other parts = 2
0...127 part10 = 7F
other parts =0
0...127 00
1...128 00
A1...A16, OFF Part No.
MONO, POLY 01
SINGLE, MULTI, INST (for DRUM) 01
NORMAL, DRUM, DRUMS1 Part10=2
other parts=0
-24...0...+24[semitones] 40
-12.8...0...+12.7[Hz] 08 00
1st bit3-0 bit7-4
2nd bit3-0 bit3-0
0...127 64
0...127 40
0...127 40
RND, L63...C...R63 40
C-2...G8 00
C-2...G8 7F
0...127 7F
0...127 00
0...127 28
0...127 00
-64...0...+63 40
-64...0...+63 40(drum part ignores)
-64...0...+63 40(drum part ignores)
-64...0...+63 40
-64...0...+63 40
-64...0...+63 40
-64...0...+63 40
-64...0...+63 40
-24...0...+24[semitones] 40
-9600...0...+9450[cent] 40
-100...0...+100[%] 40
0...127 0A
0...127 00
0...127 00
-24...0...+24[semitones] 42
-9600...0...+9450[cent] 40
-100...0...+100[%] 40
0...127 00
0...127 00
0...127 00
OFF, ON 01
OFF, ON 01
OFF, ON 01
OFF, ON 01
OFF, ON 01
OFF, ON 01
OFF, ON 01
OFF, ON XGmode=01, GMmode=00
OFF, ON 01
OFF, ON 01
OFF, ON 01
OFF, ON 01
OFF, ON 01
OFF, ON 01
OFF, ON 01
OFF, ON 01
OFF, ON XGmode=01, GMmode=00
-64...0...+63[cent] 40
-64...0...+63[cent] 40
-64...0...+63[cent] 40
-64...0...+63[cent] 40
-64...0...+63[cent] 40
-64...0...+63[cent] 40
-64...0...+63[cent] 40
-64...0...+63[cent] 40
-64...0...+63[cent] 40
-64...0...+63[cent] 40
-64...0...+63[cent] 40
-64...0...+63[cent] 40
-24...0...+24[semitones] 40
-9600...0...+9450[cent] 40
-100...0...+100[%] 40
0...127 00
0...127 00
0...127 00
-24...0...+24[semitones] 40
-9600...0...+9450[cent] 40
-100...0...+100[%] 40
0...127 00
0...127 00
0...127 00
0...95 10
-24...0...+24[semitones] 40
-9600...0...+9450[cent] 40
-100...0...+100[%] 40
5D 1 00 - 7F AC1 LFO PMOD DEPTH
5E 1 00 - 7F AC1 LFO FMOD DEPTH
5F 1 00 - 7F AC1 LFO AMOD DEPTH
60 1 00 - 5F AC2 CONTROLLER NUMBER
61 1 28 - 58 AC2 PITCH CONTROL
AC2 LOW PASS FILTER
62 1 00 - 7F
CONTROL
63 1 00 - 7F AC2 AMPLITUDE CONTROL
64 1 00 - 7F AC2 LFO PMOD DEPTH
65 1 00 - 7F AC2 LFO FMOD DEPTH
66 1 00 - 7F AC2 LFO AMOD DEPTH
67 1 00 - 01 PORTAMENTO SWITCH
68 1 00 - 7F PORTAMENTO TIME
69 1 00 - 7F PITCH EG INITIAL LEVEL
6A 1 00 - 7F PITCH EG ATTACK TIME
6B 1 00 - 7F PITCH EG RELEASE LEVEL -64...0...+63
6C 1 00 - 7F PITCH EG RELEASE TIME
6D 1 01 - 7F VELOCITY LIMIT LOW
6E 1 01 - 7F VELOCITY LIMIT HIGH
TOTAL SIZE 3F
nn = PART NUMBER(00 - 0F)
In the case of DRUM PART, the following parameters will have no effect.
BANK SELECT LSB
MONO/POLY MODE
SCALE TUNING
PORTAMENTO
<Table 1 - 6>
MIDI Parameter Change table (DRUM SETUP)
Address Size Data Parameter
(H) (H) (H)
3n rr 00 1 00 - 7F PITCH COARSE
01 1 00 - 7F PITCH FINE
02 1 00 - 7F LEVEL
03 1 00 - 7F ALTERNATE GROUP
04 1 00 - 7F PAN
05 1 00 - 7F REVERB SEND
06 1 00 - 7F CHORUS SEND
07 1 00 - 7F VARIATION SEND
08 1 00 - 01 KEY ASSIGN
09 1 00 - 01 Rcv NOTE OFF
0A 1 00 - 01 Rcv NOTE ON
LOW PASS FILTER
0B 1 00 - 7F
CUTOFF FREQUENCY
LOW PASS FILTER
0C 1 00 - 7F
RESONANCE
0D 1 00 - 7F EG ATTACK RATE
0E 1 00 - 7F EG DECAY1 RATE
0F 1 00 - 7F EG DECAY2 RATE
TOTAL SIZE 10
n = DRUM SETUP NUMBER(0 - 1)
rr = NOTE NUMBER(0D - 5B)
In the following cases, the S03 will initialize all Drum Setups.
XG SYSTEM ON received
GM SYSTEM ON received
DRUM SETUP RESET received (the designated Drum Setup only when in XG mode)
[Note]
When a part to which a Drum Setup is assigned receives a program change, the assigned
Drum Setup will be initialized.
If the same Drum Setup is assigned to two or more parts, changes in Drum Setup parame-
ters (including program changes) will apply to all parts to which it is assigned.
<Table 2 - 1>
Native Parameter Base Address
MODEL ID = 6C
Parameter Description
Address
(H) (M) (L)
NATIVE SYSTEM 00 00 00 Native System
REMOTE SWITCH 0A 00 00 Remote Switch
BULK CONTROL 0E 00 00 Header
0F 00 00 Footer
MULTI COMMON 30 00 00 Multi Common
MULTI EFFECT 30 01 00 Multi Effect
MULTI PART 31 00 00 Multi Part 1
:
31 0F 00 Multi Part 16
NORMAL VOICE COMMON 40 00 00 Normal Voice Common
NORMAL VOICE ELEMENT 41 00 00 Normal Voice Element 1
:
41 03 00 Normal Voice Element 4
DRUM VOICE COMMON 46 00 00 Drum Voice Common
DRUM VOICE KEY 47 0D 00 Drum Voice Key
0...127 00
0...127 00
0...127 00
0...95 11
-24...0...+24[semitones] 40
-9600...0...+9450[cent] 40
-100...0...+100[%] 40
0...127 00
0...127 00
0...127 00
OFF, ON 00
0...127 00
-64...0...+63 40
-64...0...+63 40
40
-64...0...+63 40
1...127 01
1...127 7F
Description Default value
(H)
-64...0...+63 40
-64...0...+63[cent] 40
0...127 depend on the note
"
OFF, 1...127
RND, L63...C...R63 "
0...127 "
0...127 "
0...127 7F
SINGLE, MULTI 00
OFF, ON depend on the note
OFF, ON 01
-64...0...63 40
-64...0...63 40
-64...0...63 40
-64...0...63 40
-64...0...63 40
Remarks
Receives parameter change only
Bulk dump only
Bulk dump only
Bulk dump only
Address Parameter
47 0D 00 note number 13
47 0E 00 note number 14
: :
47 5B 00 note number 91