Operation Chart: Module Qw-3765 - Casio G-SHOCK GW-1501B Service Manual & Parts List

2. OPERATION CHART: MODULE QW-3765

Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to read this manual carefully and keep it on hand for later reference
when necessary.
Keep the watch exposed to bright light
The electricity generated by the solar cell of the watch is
Bright Light
stored by a built-in battery. Leaving or using the watch
where it is not exposed to light causes the battery to run
down. Make sure the watch is exposed to light as much as
possible.
• When you are not wearing the watch on your wrist,
Solar cell
position the face so it is pointed at a source of bright
light.
• You should try to keep the watch outside of your sleeve
as much as possible. Even if the face of the watch is
only partially blocked from light, charging will be
significantly reduced.
• The watch continues to operate, even when it is not exposed to light. Leaving the
watch in the dark can cause the battery to run down, which will cause some watch
functions to be disabled. If the battery goes dead, you will have to re-configure watch
settings after recharging. To ensure normal watch operation, be sure to keep it
exposed to light as much as possible.
Battery charges in the light.
Bright Light
Solar cell
(Converts light to
electrical power.)
LEVEL 1
LEVEL 2
Charge
LEVEL 3
Rechargeable battery
General Guide
• Press C to change from mode to mode.
• In any mode, press B to illuminate the face of the watch.
• The Battery Level Screen shows the current battery level. See "Battery Power
Levels" for more information.
Timekeeping Mode
Timekeeping
Use the Timekeeping Mode to set and view the current time and date.
• In the Timekeeping Mode, press A to cycle through the digital time screens as
shown below.
Day of the Week
Press A.
Setting the Digital Time and Date
This watch is preset with a number of city codes, each of which represents the time
zone where that city is located. When setting the digital time, it is important that you
select the correct city code for your Home City (the city where you normally use the
watch). If your location is not included in the preset city codes, select the preset city
code that is in the same time zone as your location.
• Note that all of the times for the World Time Mode city codes are displayed in
accordance with the digital time and date settings you configure in the Timekeeping
Mode.
To set the digital time and date
1. In the Timekeeping Mode, hold down A until the city
code starts to flash, which indicates the setting screen.
2. Press D to select the city code you want.
• Make sure you select your Home City code before
changing any other setting.
• See "City Code Table" for a complete list of available
city codes.
3. Press C to move the flashing in the sequence shown below to select other settings.
DST
City Code
Power
Day
Saving
4. When the setting you want to change is flashing, use D to change it as described
below.
• The following steps explain how to configure timekeeping settings only.
Screen To do this:
Change the city code
Toggle between Daylight Saving Time
ON
( ) and Standard Time (
Toggle between 12-hour (
24H
24-hour ( ) timekeeping
Battery discharges in the dark.
Electrical
energy
All
LEVEL 1
functions
Dis- LEVEL 2
enabled
Some
charge
functions
LEVEL 3
disabled
Battery Level Screen
Press C.
Date Seconds
PM indicator
Month. Day Hour : Minutes
12/24-Hour
Seconds Hour
Format
Month Year Minutes
Do this:
Press D (east).
Press D.
OFF
)
12H Press D.
) and
• The actual level at which some functions are disabled depends on the watch model.
• Frequent display illumination can quickly run down the battery and require charging.
The following guidelines give an idea of the charging time required to recover from a
single illumination operation.
Approximately 5 minutes exposure to bright sunlight coming in through a window
Approximately 50 minutes exposure to indoor fluorescent lighting
• Be sure to read "Power Supply" for important information you need to know
when exposing the watch to bright light.
If the display of the watch is blank...
If the display of the watch is blank, it means that the watch's Power Saving function
has turned off the display to conserve power.
• See "Power Saving" for more information.
About This Manual
Hour hand Minute hand
Digital display
World Time Mode
NYC
Hand Setting Mode
Screen To do this:
Reset the seconds to
Change the hour or minutes
Time
Change the year
Change the month or day
5. Press A to exit the setting screen.
• When you exit the setting screen, the analog hands are adjusted automatically to
match the digital time. See "Analog Timekeeping" for more information.
• See "Daylight Saving Time (DST)" for details about the DST setting.
• For information about specifying how long the face of the watch remains illuminated,
see "To specify the illumination duration".
• For details about configuring settings for the Power Saving feature, see "Power
Saving".
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To toggle the Timekeeping Mode digital time between DST and Standard Time
Analog Timekeeping
The analog time of this watch is synchronized with the digital time. The analog time
setting is adjusted automatically whenever you change the digital time.
Note
• The hands for the analog timepiece move to adjust to a new setting whenever any of
the following occurs.
When you change the digital time setting
When you change the Home City code and/or DST setting
• If the analog time does not match the digital time for some reason, use the
procedure below to adjust the analog time to the digital time.
• Whenever you need to adjust both the digital and the analog time settings manually,
make sure you adjust the digital setting first.
• Depending on how much the hands have to move in order to adjust to the digital
time, it may take some time before they stop moving.
— 2 —
• Button operations are indicated using the letters shown
in the illustration.
• Most of the display examples in this manual show only
the digital display, without the analog hands.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the "Reference" section.
Alarm Mode
Stopwatch Mode
STW
Do this:
Press D.
00
Press D(to increase).
1. In the Timekeeping Mode, hold down A until the city
code starts to flash, which indicates the setting screen.
2. Press C once and the DST setting screen appears.
3. Press D to toggle between Daylight Saving Time (
displayed) and Standard Time ( OFF displayed).
4. Press A to exit the setting screen.
• The DST indicator appears on the display to indicate
that Daylight Saving Time is turned on.
ON