Installing the Vehicle Dock Put the ball joint through the ball joint fastener. Insert the ball joint into the ball joint socket on the back of the vehicle dock. And lock the ball joint by screwing on the ball joint fastener.
Lock the ball joint by screwing on the ball join fastener. Clean and dry the surface where the Vehicle dock will be mounted. Press the suction surface firmly to the window and latch the lever to attach the suction holder.
When mounting on the dashboard, press the suction surface firmly to the Dashboard pad and latch the lever to attach the suction holder. Remove the adhesive film from the Dashboard pad, and then press the pad firmly to the dashboard. • Carefully choose the installation location.
Using the device This Vehicle dock is suitable for 1016 mm ~1448 mm Samsung mobile devices. Press the button on the back of the Vehicle dock to open the side grip arms. Place the mobile device in the Vehicle dock and then press the side grip arms to hold your device.
When the Vehicle dock is connected to the electric socket, the indicator light flashes from red to green to orange, and then turns off. • Use only Samsung-approved chargers. Unauthorised chargers may damage your device or cause the battery to explode.
Indicator light Device status Red → Green When connected to the power → Orange outlet Flashes orange When not charging properly Green When charging properly Flashes green When using a charger under 2 A When in Idle mode The Vehicle dock’s indicator light flashes differently depending on its status.
When your device is fully charged, unplug the charging cable from the Vehicle dock and the car adapter from the accessory outlet. • Check the mobile device’s battery status using the charging icon displayed on the screen. • The initial charging may not start when the Vehicle dock is left inside a vehicle with high temperature, and the indicator light flashes orange.
Do not place the Wireless Charging Cover solely on the Vehicle dock Doing so may overheat the device and cause a fire. It may also result in serious burn or device malfunction.
To prevent injury to yourself and others or damage to your device, read the safety information about your device before using the device Samsung cannot be held responsible for any injury or property damage caused by failure to comply with the safety cautions and regulations...
• Any changes or modifications to your device can void your manufacturer’s warranty. If your device needs servicing, take your device to a Samsung Service Centre. When cleaning your device, mind the following • Wipe your device or charger with a towel or an eraser.
Do not mount your device in any location that interferes with safe operation of the vehicle, as this may lead to an accident • Install where the driver’s vision is not compromised • Install where the driver or passenger cannot be harmed when the device detaches unexpectedly.
Doing so may deform the device, result in damage to the device, or cause the battery to explode. To avoid potentially dangerous situations or damage to your equipment, use only the supplied accessories or those approved by Samsung...
Do not use the device during a thunderstorm Thunderstorms can cause the device to malfunction and increase the risk of electric shock. Prevent the multipurpose jack and the small end of the charger from contact with conductive materials, such as liquids, dust, metal powders, and pencil leads Conductive materials may cause a short circuit or corrosion of the terminals, which may result in an explosion or fire.
Correct disposal of this product (Waste Electrical & Electronic Equipment) (Applicable in countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste.
Declaration of Conformity Samsung Electronics declares that this device complies with the essential requirements and relevant provisions of Directive 1999/5/EC. Go to www.samsung.com/mobile_doc to view the Declaration of Conformity.
FCC ID: A3LEP-HN910IBU FCC Part 15.19 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IC: 649E-EPHN910IBU This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.