Kyosho USA-1 Monster Truck Manual page 2

r
•
BEFORE ASSEMBLY
ORead the instruction carcfull)•.
You can assemble the kit more easily
if you have grasped the general idea
or steps and structure beforehand by
reading it through to the end.
OCheck the parts in the kit.
Instruct ion
Check to
see
if all the parts are correctly bagged as they are listed
0
Be
well aware of the diHerent types or screws.
The difference between the TP Screw (short form of self-tapping
screw) and the ordinnrly screw is .....
• TP Screw
ail!!!'!!: ID
I Some of them pointed tips.
Coarser Thread
• Ordinnrly ScrewQ '
Finer Thread
=-..-
A hexagonal
• Set Screw
~
hollow in place
in the Bagged Parts List. Your through understanding of the assembly
of screw head.
prior to starting
will enable you to
build the kit
without am·
difficulty. •
OCheck the components in the kit prior to )'Our startlngs
or the assembly.
Any claims for replacements or refunds for the
model in the process of assembly will not accepted
without shortage or in!criorit)' or the pans.
0
Learn on the marks described in the instruction.
- g ) ...
Place where grease should be applied.
c==-
0
Pick up the correct parts and screw.
Compare the shape and size of small parts.
such as screws. nuts. and washers with
the actual size drawing in each step.
0
Be
sure about the location and direction or
parts to install.
Double-check the location and direction or
?;
parts with the illustraton before installation.
When necessary. assemble the parts themselves
tentatively before proceeding to the next step.
0
no
not tighten the TP Screw too strong ...
'
Direction
.
'
--
Do not usc excessive force when tightening the TP Screws. or you
may strip the thread in the plastic. It is recommended to stop
tightening it when the thread part on the screw goc. into the plastic
part and you reel someresista nee . .
from the tightening Q,•cr tighten may stnp the
· thread in the plastic.
(
It will reduce friction to assure
smooth movements.
)
Steps where your
particular attention
is required.
GOOD
TIIINGS NEED BESIDES T ilE KIT
(2
Channel Radio System)
Transrniuer
(:\A Size Battery)
This model is designed for
BEC system radio only.
Usc a radio which has a mark
shown at left.
Two types of radio control set arc
on the market. the stick type and
the steering wheel type,
Choose which ever you like.
Servo
f'or Transmitter .... 8 pes.
(1-11 -Cad Battery)
This model is designed to usc a rechargeable 7.2V Sprint
Battery SCR and 7.2V Power Battery.
1'\o.2310
7.2V Sprint Battery SCR
l':o.2306
7.2V Power Battery
(Charger lor NI-Cad Ballcry)
The Kyosho's l'i-Cad Dauer)' is high performance. If it is charged correctly.
it will operate for a considerable period.
Usc one of the chargers listed below which suits your need.
NO. Name
2326 7.2V Power Charger
1849 Multi Charger II
2246
f'ET Auto Charger
0 · - - · - ·
Time
15 min.
l~ate
Features
7096 For biginncrs
Built- in timer
20 min. 10096
Timer. Ammeter built- in
20 min. 10096 Trickle charging. Automatic
cut -orr at peak of charge
(Tools Required) A Hex kC)', Grease and Cross Wrench are in the kit.
Polyca Color Paint
:0.1icron Line
Tape
Philips Screw Driver (L.M.S) Awl
--<======
• • 0 . . •
.....
cr:
!
D
Screw Driver
(M)
C=t
§
J
D
Sander
Sharp llobb}
Knife
Brush
Instant
Glue
lii lliC:[IJMC= ::JIIJI
- 2