Table of Contents
Advertisement
Quick Links
Description
Original Release - Firmware version 1.0.7
Revised Oct 2013 Firmware version 2.1.2
Revised Jan 2014 Firmware version 2.13
Revised Apr 2014 Firmware version 2.15
Revised Jan 2016 Include FCC statement
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this equipment. (Example - use
only shielded interface cables when connecting to computer or peripheral devices).
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
AMR170 Series NFC Reader
User Manual
Document History
Model
AMR171,AMR175
AMR171,AMR175
AMR171,AMR175
AMR171,AMR175
AMR171,AMR175
Advertisement
Table of Contents
Related Manuals for ASIS Technologies AMR171
Summary of Contents for ASIS Technologies AMR171
- Page 1 AMR170 Series NFC Reader User Manual Document History Model Description AMR171,AMR175 Original Release - Firmware version 1.0.7 AMR171,AMR175 Revised Oct 2013 Firmware version 2.1.2 AMR171,AMR175 Revised Jan 2014 Firmware version 2.13 AMR171,AMR175 Revised Apr 2014 Firmware version 2.15 AMR171,AMR175 Revised Jan 2016 Include FCC statement...
-
Page 2: Dip Switch Setting
Yellow Hold Purple Table 2 Wiring and Cable Color code 1.3 DIP Switch Setting AMR171/175 series reader has 8 way DIP switch with function as show in below table. Label Function in RS485 Function in Wiegand Address bit 0 Card format setting... - Page 3 Note: Bit 7 CAN refer to Card Application Number found on Ez-Link card. Bit 1 Bit 2 Bit3 Bit4 Bit5 Bit6 Bit7 Bit 8 Label Refers to Table 3 for other DIP Switch Setting. Address Table 4 RS485 Readers Address Dip Switch Setting DIPSW DIP1 DIP2...
- Page 4 Figure 1 Physical Dimension Figure 2 Removal of Cover To remove the reader’s cover, unscrew the screw in the bottom and flip open the cover. Figure 3 Mounting Method...
- Page 5 PIN is up to 6 digit. When the reader is powered-up, the LED and the Buzzer will respond. Buzzer response LED Response LCD Display (For AMR175 Description (AMR171/175) (AMR171/175) only) a) Upon Power Up the The buzzer will beep Model No Reader Address Reader’s Amber LEDs...
-
Page 6: Radio Frequency Interference
1.5m away from the any devices that emits RF that may interfere with the signal received from the access control cards. 1.6 Package List - AMR171/175 Reader Item Description Qty. Complete with snap on cover 1 Mounting cover screw, M3 1 Installation and this... - Page 7 1.7 Product Electrical Specification Power Supply (Recommend) Regulated linear power supply, +12VDC, 300mA Operating Voltage Range +9VDC - + 24VDC Operating Current at +12VDC 85mA (average) – 185mA (peak) 150meters (500feet) (base on Belden 9538 24AWG 0.6mm, 8 core cable foilshield) (for Maximum Cable Distance wiegand interface) (base on Belden 9534 24AWG 06.mm, 4 core cable foilshield) (for...
- Page 8 Support Card Type Mifare ( ISO 14443-A, ISO 14443-B) EZ-Link Output CAN or CSN (Selectable) Mounting Hook On Bracket...
Need help?
Do you have a question about the AMR171 and is the answer not in the manual?
Questions and answers