Summary of Contents for Multiform VersoClub-HT3012
Page 1
USER MANUAL VersoClub-HT3012 DMX-controlled RGB 4-Segment Mini LED Stage Bar For firmware 50-015-0308-00103-1-00 Firmware RevD (MKIII-MF 4SEG-S2L) ENGLISH Page 2-19 RevC 01 01/2014 Order code: 12-015-0303-80203-1-01...
■ Technical data VersoClub-HT3012 SAFETY INFORMATION LEDs………………..…………………..…………… 4 panels, each 3x3W RGB MulTriLED Dispersion angle……………………………………………………………………………. 40°...
Page 3
User Manual: VersoClub-HT3012 User Manual: VersoClub-HT3012 ■ Security advice before use General advice: Read this manual completely before using the product. Keep this manual in your records for future reference. Follow all instruction printed in this manual. Follow all printed security advice on the product itself.
Page 4
User Manual: VersoClub-HT3012 User Manual: VersoClub-HT3012 Protection from fire: CH13= 000...255 Panel 3 Dimmer BLUE CH14= 000...255 Panel 3 Master Dimmer Take care of not placing the unit near sources of heat (e.g. CH15= 000...255 Panel 3 Strobe powerful amplifiers, fog machines).
Page 5
CH8 = 000...255 Panel 2 Dimmer BLUE CH9 = 000...255 Panel 2 Master Dimmer Main parts: 1 pc. VersoClub-HT3012 main unit CH10= 000...255 Panel 2 Strobe 1 pc. mains cable CH11= 000…255 Panel 3 Dimmer RED 1 pc.
Page 6
228…255 Master Dimmer = 100% Strobe off dC5 = DMX Combined 5CH Mode The VersoClub-HT3012 is designed to be mounted on a tripod with 35mm tube Function: 3 colors RGB + separate master/strobe for all panels diameter. It can both be mounted on top as well as in any other height on the tripod The unit receives DMX values on a packet of 5 consecutive DMX channels, with the tube.
Page 7
A 4-step pattern. Transition is switching in Switch Pattern mode, and fading in Hanging/Rigging, ceiling-mounted operation Fade pattern mode. Further to the tripod mounting adaptor, the VersoClub-HT3012 is equipped with two A19 (switching+strobe) : M10 thread insert mounting points on the top of the unit. These can typically be used to A Strobe pattern.
Page 8
In “S” mode, the unit does not receive any values from the DMX input but generates The VersoClub-HT3012 has an AC outlet that is designed to carry loads related DMX values on the output (12CH) according to the selected pattern, so that further units can show the same behaviour if they are connected by DMX signal cables of no more than 8A.
Page 9
User Manual: VersoClub-HT3012 User Manual: VersoClub-HT3012 The output level (brightness) can be set in 10 levels: 10% | 20% | 30% | 40% | 50% | ■ Operation 60% | 70% | 80% | 90% | 100%. To do this with the on-board user interface, the user must change into COLOR mode first and make a global brightness adjustment as described in the COLOR mode chapter.
Page 10
User Manual: VersoClub-HT3012 User Manual: VersoClub-HT3012 and then pressing the UP or DOWN buttons to change the brightness. The current level Color Definitions (in DMX values) as below: is displayed while making the adjustment. Note that the brightness setting using the on-...
Need help?
Do you have a question about the VersoClub-HT3012 and is the answer not in the manual?
Questions and answers