Page 1
COMPONENTS IDENTIFIED BY MARK ON THE SCHEMATIC DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK. REPLACE THESE COMPONENTS WITH ONKYO PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL. MAKE LEAKAGE-CURRENT OR RESISTANCE...
Page 2
HTP-420 SPECIFICATIONS Powered Subwoofer (SKW-420) Center Speaker (SKC-420C) Bass-reflex with built-in 2 Way Bass-reflex Type : Type : power amplifier Impedance : 8 ohm Input sensitivity/impedance : 220 mV / 15 k ohm Maximum input power : 100 W Maximum output power :...
Page 3
HTP-420 EXPLODED VIEWS-1 SKW-420 : POWERED SUBWOOFER <Notes> SP06 A06 (POWER SWITCH) : x 10 pcs. MDD type --- No MDC type --- No MDT type --- No MDD type MPA type --- Yes MDC type --- Yes MGT type...
Page 4
HTP-420 EXPLODED VIEWS-2 SKW-420 : POWERED SUBWOOFER SP01 SP02 x 4 pcs. SP04 SP03 SP08 SP06 x 8 pcs. SP05 x 8 pcs.
Page 5
HTP-420 EXPLODED VIEWS-3 SKF-420F / SKC-420C / SKM-420S SP10 SP12 SP14 SP15 SP11 SP13 I N A l a c G r e I N A I N A l a c l a c i t e R e d "SKC-420C"...
Page 7
HTP-420 SCHEMATIC DIAGRAM SKW-420 : POWERED SUBWOOFER LINE INPUT OUTPUT LEVEL RED : STANDBY GREEN : ON INPUT PC BOARD VR / LED PC BOARD AC 120V / 60Hz <Note> <Note> AC 220-230V / 50Hz POWER SWITCH* / C1** C913*** / C914***...
Page 9
HTP-420 SCHEMATIC DIAGRAM SKW-420 : POWERED SUBWOOFER SPEAKER LINE INPUT OUTPUT LEVEL RED : STANDBY GREEN : ON INPUT PC BOARD VR / LED PC BOARD MAIN PC BOARD AC 120V / 60Hz <Note> <Note> AC 220-230V / 50Hz POWER SWITCH* / C1**...
Page 10
HTP-420 PC BOARD CONNECTION DIAGRAM SKW-420 : POWERED SUBWOOFER INPUT PC BOARD MAIN PC BOARD VR / LED PC BOARD <Notes> POWER SWITCH : MDD type --- No MDC type --- No MDT type --- No MPA type --- Yes...
Page 11
HTP-420 PRINTED CIRCUIT BOARD VIEW SKW-420 : POWERED SUBWOOFER MAIN PC BOARD INPUT PC BOARD VR / LED PC BOARD No PC board view Look over the actual PC board on hand...
Page 12
TDA7293 ® 120V - 100W DMOS AUDIO AMPLIFIER WITH MUTE/ST-BY VERY HIGH OPERATING VOLTAGE RANGE MULTIPOWER BCD TECHNOLOGY (±50V) DMOS POWER STAGE HIGH OUTPUT POWER (100W @ THD = = ±40V) 10%, R = 8Ω, V MUTING/STAND-BY FUNCTIONS NO SWITCH ON/OFF NOISE VERY LOW DISTORTION Multiwatt15V Multiwatt15H...
Page 13
TDA7293 PIN CONNECTION (Top view) (POWER) (POWER) BOOTSTRAP LOADER BUFFER DRIVER MUTE STAND-BY (SIGNAL) (SIGNAL) BOOTSTRAP CLIP AND SHORT CIRCUIT DETECTOR SIGNAL GROUND NON INVERTING INPUT INVERTING INPUT STAND-BY GND TAB CONNECTED TO PIN 8 D97AU806 ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit...
Page 14
TDA7293 = ±40V, R = 50 Ω; ELECTRICAL CHARACTERISTICS (Refer to the Test Circuit V = 8Ω, R = 25°C, f = 1 kHz; unless otherwise specified). Symbol Parameter Test Condition Min. Typ. Max. Unit ±12 ±50 Supply Range Quiescent Current µA Input Bias Current Input Offset Voltage...
Page 16
TDA7293 APPLICATION SUGGESTIONS (see Test and Application Circuits of the Fig. 1) The recommended values of the external components are those shown on the application circuit of Fig- ure 1. Different values can be used; the following table can help the designer. LARGER THAN SMALLER THAN COMPONENTS...
Page 17
TDA7293 frequency response; moreover, an accurate con- INTRODUCTION trol of quiescent current is required. In consumer electronics, an increasing demand A local linearizing feedback, provided by differen- has arisen for very high power monolithic audio tial amplifier A, is used to fullfil the above require- amplifiers able to match, with a low cost, the per- ments, allowing a simple and effective quiescent formance obtained from the best discrete de-...
Page 18
TDA7293 Figure 4: Turn ON/OFF Suggested Sequence V IN (mV) V ST-BY PIN #9 V MUTE PIN #10 (mA) V OUT ST-BY PLAY ST-BY MUTE MUTE D98AU817 mute functions, independently driven by two In addition to the overload protection described CMOS logic compatible input pins.
Page 19
TDA7293 The TDA7293 is a monolithic MOS power ampli- The main advantages offered by this solution are: fier which can be operated at 100V supply voltage - High power performances with limited supply (120V with no signal applied) while delivering out- voltage level.
Page 25
TDA7293 inch DIM. OUTLINE AND MIN. TYP. MAX. MIN. TYP. MAX. MECHANICAL DATA 0.197 2.65 0.104 0.063 0.49 0.55 0.019 0.022 0.66 0.75 0.026 0.030 1.14 1.27 0.045 0.050 0.055 17.57 17.78 17.91 0.692 0.700 0.705 19.6 0.772 20.2 0.795 20.57 0.810 18.03...
Page 26
TDA7293 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics.
Page 27
August 2000 LM124/LM224/LM324/LM2902 Low Power Quad Operational Amplifiers General Description Advantages n Eliminates need for dual supplies The LM124 series consists of four independent, high gain, internally frequency compensated operational amplifiers n Four internally compensated op amps in a single which were designed specifically to operate from a single package power supply over a wide range of voltages.
Page 28
Connection Diagram (Continued) Note 3: See STD Mil DWG 5962R99504 for Radiation Tolerant Device DS009299-33 Order Number LM124AW/883, LM124AWG/883, LM124W/883 or LM124WG/883 LM124AWRQML and LM124AWRQMLV(Note 3) See NS Package Number W14B LM124AWGRQML and LM124AWGRQMLV(Note 3) See NS Package Number WG14A Schematic Diagram (Each Amplifier) DS009299-2...
Page 29
Absolute Maximum Ratings (Note 12) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. LM124/LM224/LM324 LM2902 LM124A/LM224A/LM324A Supply Voltage, V Differential Input Voltage Input Voltage −0.3V to +32V −0.3V to +26V Input Current <...
Page 30
Electrical Characteristics (Continued) = +5.0V, (Note 7), unless otherwise stated LM124A LM224A LM324A Parameter Conditions Units Power Supply = 5V to 30V Rejection Ratio (LM2902, V = 5V to 26V), = 25˚C Amplifier-to-Amplifier f = 1 kHz to 20 kHz, T = 25˚C −120 −120...
Page 31
Electrical Characteristics (Continued) = +5.0V, (Note 7), unless otherwise stated LM124/LM224 LM324 LM2902 Parameter Conditions Units = 25˚C Amplifier-to-Amplifier f = 1 kHz to 20 kHz, T = 25˚C −120 −120 −120 Coupling (Note 11) (Input Referred) − Output Current Source = 1V, V = 0V,...
Page 32
Typical Performance Characteristics Input Voltage Range Input Current DS009299-34 DS009299-35 Supply Current Voltage Gain DS009299-36 DS009299-37 Open Loop Frequency Common Mode Rejection Response Ratio DS009299-38 DS009299-39 www.national.com...
Page 33
Typical Performance Characteristics (Continued) Voltage Follower Pulse Voltage Follower Pulse Response Response (Small Signal) DS009299-40 DS009299-41 Large Signal Frequency Output Characteristics Response Current Sourcing DS009299-42 DS009299-43 Output Characteristics Current Limiting Current Sinking DS009299-45 DS009299-44 www.national.com...
Page 34
Typical Performance Characteristics (Continued) Input Current (LM2902 only) Voltage Gain (LM2902 only) DS009299-46 DS009299-47 Application Hints The LM124 series are op amps which operate with only a Where the load is directly coupled, as in dc applications, single power supply voltage, have true-differential inputs, there is no crossover distortion.
Page 35
Typical Single-Supply Applications = 5.0 V Non-Inverting DC Gain (0V Input = 0V Output) DS009299-5 R not needed due to temperature independent I DC Summing Amplifier Power Amplifier ≥ 0 V ≥ V and V IN’S DS009299-7 = 0 V for V = 0 V DS009299-6...
Page 36
Typical Single-Supply Applications = 5.0 V ) (Continued) LED Driver “BI-QUAD” RC Active Bandpass Filter DS009299-8 DS009299-9 = 1 kHz Q = 50 = 100 (40 dB) Fixed Current Sources Lamp Driver DS009299-11 DS009299-10 www.national.com...
Page 37
Typical Single-Supply Applications = 5.0 V ) (Continued) Current Monitor Driving TTL DS009299-13 DS009299-12 (Increase R1 for I small) Voltage Follower Pulse Generator DS009299-14 DS009299-15 www.national.com...
Page 38
Typical Single-Supply Applications = 5.0 V ) (Continued) Squarewave Oscillator Pulse Generator DS009299-16 DS009299-17 High Compliance Current Sink DS009299-18 = 1 amp/volt V (Increase R for I small) www.national.com...
Page 39
Typical Single-Supply Applications = 5.0 V ) (Continued) Low Drift Peak Detector DS009299-19 Comparator with Hysteresis Ground Referencing a Differential Input Signal DS009299-20 DS009299-21 www.national.com...
Page 40
Typical Single-Supply Applications = 5.0 V ) (Continued) Voltage Controlled Oscillator Circuit DS009299-22 ≤ V ≤ 2 (V Wide control voltage range: 0 V −1.5 V Photo Voltaic-Cell Amplifier DS009299-23 AC Coupled Inverting Amplifier DS009299-24 www.national.com...
Page 41
Typical Single-Supply Applications = 5.0 V ) (Continued) AC Coupled Non-Inverting Amplifier DS009299-25 DC Coupled Low-Pass RC Active Filter DS009299-26 = 1 kHz Q = 1 www.national.com...
Page 42
Typical Single-Supply Applications = 5.0 V ) (Continued) High Input Z, DC Differential Amplifier DS009299-27 High Input Z Adjustable-Gain DC Instrumentation Amplifier DS009299-28 www.national.com...
Page 43
Typical Single-Supply Applications = 5.0 V ) (Continued) Using Symmetrical Amplifiers to Bridge Current Amplifier Reduce Input Current (General Concept) DS009299-30 DS009299-29 Bandpass Active Filter DS009299-31 = 1 kHz Q = 25 www.national.com...
Page 44
Physical Dimensions inches (millimeters) unless otherwise noted Ceramic Dual-In-Line Package (J) Order Number JL124ABCA, JL124BCA, JL124ASCA, JL124SCA, LM124J, LM124AJ, LM124AJ/883, LM124J/883, LM224J, LM224AJ or LM324J NS Package Number J14A MX S.O. Package (M) Order Number LM324M, LM324MX, LM324AM, LM324AMX, LM2902M or LM2902MX NS Package Number M14A www.national.com...
Page 45
Physical Dimensions inches (millimeters) unless otherwise noted (Continued) Molded Dual-In-Line Package (N) Order Number LM324N, LM324AN or LM2902N NS Package Number N14A Ceramic Flatpak Package Order Number JL124ABDA, JL124ABZA, JL124ASDA, JL124BDA, JL124BZA, JL124SDA, LM124AW/883, LM124AWG/883, LM124W/883 or LM124WG/883 NS Package Number W14B www.national.com...
Page 46
Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 14-Pin TSSOP Order NumberLM324MT or LM324MTX NS Package Number MTC14 LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION.
Page 48
YLB810004SL10 EXPLODED SP18 COMPLETE UNIT "SKM-420S (S) R" ANU8S670SBM11 EXPLODED SP19 BACK LABEL (R) YLB810004SR10 EXPLODED HTP-420 PRINTED CIRCUIT BOARD PARTS LIST CIRCUIT NO. PART NAME DESCRIPTION Q'TY PART NO. (SN) MARK IC501 POWER IC 15PIN TDA7293 RHI007293-0001 DB901 DIODE...
Page 49
Tel: 201-785-2600 Fax: 201-785-2650 http://www.onkyousa.com ONKYO EUROPE ELECTRONICS GmbH Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.onkyo.net ONKYO CHINA LIMITED Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung, N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039 HOMEPAGE http://www.onkyo.com/...