Viewing Caller Lists And Stored Number Removal; Programming Button; Testing Your Connection To The Dpb - Digitone proseries blocker Operation Manual

Programming Button

LINE port, with an analog telephone connected to the TEL port. The DPB will display "Connect to Line
Service" until line service is connected to the LINE port. Power must be connected to the DPB with the
Digitone supplied 24VDC power adapter. You will not be able to program the DPB unless the above
conditions are met. Leave all other phone devices you have connected to their own power supplies.
With this setup done, press and hold the Program Button for 3 seconds until you see the red LED light,
then release button, see "Program Mode", then "Pick Up Phone". Note that if you are using a cordless
phone handset you will also have to press the Talk button. When you pick up that phone connected
to the TEL phone port on the back of the DPB, the display will now show "Enter Code".
remain on the line using your phone offhook when programming, so don't hang-up the phone. Enter any
program code listed in the manual by simply dialing that program code with the phone's keypad
to set caller lists or features. If you don't see Enter Code, then refer to page 1 above for a review of your
installation.

Testing your connection to the DPB

Go offhook with the phone you are using in the TEL port. See if the DPB shows the Call Progress
Timer on the lower line of the display, ex. 0:01, 0:02, etc. before attempting programming. If so, then
you should be able to see the prompt "Enter Code" when you take that phone offhook again following the
prompt "Pick Up Phone" when entering programming. If you don't see the prompt "Enter Code", then
you are using a phone not directly connected to the TEL port of the DPB.

Viewing Caller Lists and Stored Number Removal

You can review what numbers are stored in each caller list by entering programming: press and hold the
Program Button for 3 seconds until you see "Program Mode", then "Pick Up Phone", when the prompt
for "Enter Code" displays enter:
Code 21
to view Spoofed Exchange Call list – use arrow buttons to view up or down. To remove
or unblock an entry press and hold the Block Button for 3 seconds on the front panel. The number
will then be removed from that list. See page 2 for Spoofed Exchange program instructions.
Code 41
to view Blocked Caller list – use arrow buttons to view up or down. To remove or
unblock an entry press and hold the Block Button for 3 seconds on the front panel. The number will
then be removed from that list. See page 6 for Blocking Known Unwanted Callers program instructions.
Code 43
to view Blocked Outgoing Dialed Numbers list - use arrow buttons to view up or down.
To remove or unblock an entry press and hold the Block Button for 3 seconds on the front panel.
The number will then be removed from that list.
Code 44
to view Blocked Names list - Names can only be removed with this function in
programming. Use arrow buttons to view up or down. To remove or unblock an entry press and
hold the Block Button for 3 seconds on the front panel. The name will then be removed from that list.
Code 51
to view Invited Caller list – use arrow buttons to view up or down. To remove a stored
invited entry press and hold the Block Button for 3 seconds on the front panel. The number will then
be removed from that list. See page 6 for Inviting Individual Callers program instructions.
Code 53
to view Invited Caller in a Blocked Area Code list – use arrow buttons to view up or
down. To remove a stored invited entry press and hold the Block Button for 3 seconds on the
front panel. The number will then be removed from that list.
Code 61
to view VIP Caller list – use arrow buttons to view up or down. To remove a stored VIP
entry press and hold the Block Button for 3 seconds on the front panel. The number will then be
removed from that list. See page 6 for Inviting VIP Callers program instructions.
First Ring Suppression
When a call comes in, the phone company's Caller ID information will display on all phones connected
to the telephone line but the DPB will suppress the first ring to the TEL phone port to prevent it
BLUE
The DPB must be connected to an analog telephone line source in the
™
– Caller ID Pass Thru Mode Code 70
5
You must