Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for WiMAX RG300
Summary of Contents for WiMAX RG300
- Page 1 UIDE MAX 802.16 NDOOR ATEWAY RG300...
- Page 3 Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: EN 60950-1 :2006 + A11:2009 Safety of Information Technology Equipment...
- Page 4 Information technology equipment — Immunity characteristics — Limits and methods of measurement This device is a 2.3G & 2.5G Wimax + 2.4G Wifi wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies.
- Page 5 0560 Česky [Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se [Czech] základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [Danish] [udstyrets typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
- Page 6 Polski Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z [Polish] zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Português [Nome do fabricante] declara que este [tipo de equipamento] está conforme [Portuguese com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. Slovensko [Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami [Slovenian]...
- Page 7 UIDE RG300 WiMAX IEEE 802.16e Indoor Gateway with 2.3 and 2.5 GHz Frequency Band Support, Up to Four LAN (RJ-45) Ports, Up to Two VoIP (RJ-11) Ports, and Optional 802.11n Wi-Fi Models with Wi-Fi RG300 RG300-2.5 RG300-2.3 RG300-2.5-4D2V1W RG300-2.3-4D2V1W RG300-2.5-4D1W RG300-2.3-4D1W...
-
Page 8: Compliances
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Due to the essential high output power nature of WiMAX devices, use of this device with other transmitters at the same time may exceed the FCC RF exposure limit and such usage must be prohibited (unless such co- transmission has been approved by FCC in the future). - Page 9 (V1.2.2) - EMC requirements for radio equipment This device is intended for use in all European Community countries. NCC 警語 Wi-Fi: 經型式認證合格之低功率射頻電機 , 非經許可 , 公司、商號或使用者均不得擅 自變更頻率、加大功率或變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信 ; 經發現有干擾現象 時 , 應立即停用 , 並改善至無干擾時方得繼續使用。前項合法通信 , 指依電信 法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫 療用電波輻射性電機設備之干擾。 WiMAX: 減少電磁波影響 , 請妥適使用。 – 4 –...
-
Page 10: About This Guide
BOUT UIDE This guide details the hardware features of the RG300 WiMAX 802.16e URPOSE Indoor Gateway, including its physical and performance-related characteristics, and how to install the device and use its configuration software. This guide is for PC users with a working knowledge of computers. You UDIENCE should be familiar with Windows operating system concepts. -
Page 11: Table Of Contents
ONTENTS OMPLIANCES BOUT UIDE ONTENTS IGURES ABLES ECTION ETTING TARTED NTRODUCTION RG300 Hardware Description Wi-Fi Option Power Status LED Wi-Fi Status LED WiMAX Signal LEDs LAN Ports VoIP Phone Ports Power Adapter Socket Reset Button RG300 NSTALLING THE Package Checklist... - Page 12 ONTENTS Common Web Page Buttons ECTION ONFIGURATION YSTEM ETTINGS System Status Administrator Settings Firmware Upgrade Configuration Tools System Time System Log Reset 5 WAN C ONFIGURATION WAN Settings Dynamic IP Address Static IP Settings L2TP Settings PPTP Settings DDNS 6 LAN C ONFIGURATION LAN Settings DHCP Client List...
- Page 13 ONTENTS Host Filtering OUTING ONFIGURATION Routing Table Static Route 10 UP ONFIGURATION UPnP 11 V IP S ETTINGS SIP Account SIP Settings Speed Dial Dial Plan Call Feature Phone Settings Codecs 12 W ETTINGS Basic Wireless Settings Advanced Wireless Settings Wireless Security Wired Equivalent Privacy (WEP) WPA Pre-Shared Key...
- Page 14 ONTENTS Physical Specifications WiMAX Specifications VoIP Specifications Wi-Fi Specifications Compliances ABLES AND INOUTS Twisted-Pair Cable Assignments 10/100BASE-TX Pin Assignments Straight-Through Wiring Crossover Wiring RJ-11 Port LOSSARY NDEX – 9 –...
-
Page 15: Figures
IGURES Figure 1: Front of the RG300 Figure 2: RG300 LED Indicators Figure 3: Back of the RG300 Figure 4: Base of the RG300 Figure 5: RG300 Connections Figure 6: Login Page Figure 7: Home Page Figure 8: WiMAX Account Login... - Page 16 IGURES Figure 32: NAT Settings Figure 33: Port Mapping Figure 34: DMZ Settings Figure 35: ALG Settings Figure 36: Firewall Settings Figure 37: Client Filtering Settings Figure 38: Port Filtering Figure 39: MAC Filtering Figure 40: URL Filtering Figure 41: Host Filtering Figure 42: Routing Table Figure 43: Static Route Figure 44: UPnP Setting...
-
Page 17: Tables
ABLES Table 1: Power Status LED Table 2: Wi-Fi Status LED Table 3: WiMAX Signal Status LEDs Table 4: LAN Port Status LED Table 5: Dial Plan Elements Table 6: Troubleshooting Chart Table 7: 10/100BASE-TX MDI and MDI-X Port Pinouts Table 8: RJ-11 Port Pinout –... -
Page 18: Sectioni
ECTION ETTING TARTED This section provides an overview of the RG300, and describes how to install and mount the unit. It also describes the basic settings required to access the management interface and run the setup Wizard. This section includes these chapters: “Introduction”... -
Page 19: Introduction
DSL or cable modems. The RG300 includes up to four RJ-45 Ethernet ports for LAN connections and up to two RJ-11 Voice over IP (VoIP) phone ports. Units also support an IEEE 802.11b/g/n Wi-Fi module that provides a local Wi-Fi access point service. -
Page 20: Rg300 Hardware Description
RG300 H ARDWARE ESCRIPTION The front of the RG300 provides an array of system status indicators. The back includes four LAN ports for 10/100 Mbps Ethernet connections, two RJ-11 VoIP phone ports, and a DC power jack. Figure 1: Front of the RG300 The RG300 includes an 802.11b/g/n Wi-Fi support. -
Page 21: Power Status Led
| Introduction HAPTER RG300 Hardware Description The RG300 includes a Power LED indicator that simplifies installation and OWER TATUS WiMAX network troubleshooting. The LED, which is located on the front panel, is described in the following table. Figure 2: RG300 LED Indicators... -
Page 22: Wi-Fi Status Led
| Introduction HAPTER RG300 Hardware Description The RG300 includes a Wi-Fi LED indicator that displays the Wi-Fi network TATUS status. The LED, which is located on the front panel, is described in the following table. Table 2: Wi-Fi Status LED... -
Page 23: Voip Phone Ports
The unit is powered on when connected to its AC power adapter, and the power adapter is connected to an AC power source between 100-240 volts at 50-60Hz. The Reset button is located on the base of the RG300 and is used to reset ESET UTTON the unit or restore the factory default configuration. -
Page 24: Figure 4: Base Of The Rg300
| Introduction HAPTER RG300 Hardware Description changes you may have made are removed, and the factory default configuration is restored to the unit. Figure 4: Base of the RG300 Reset Button – 19 –... -
Page 25: Installing The Rg300
NSTALLATION VERVIEW Before installing the RG300, verify that you have all the items listed in the package checklist above. If any of the items are missing or damaged, contact your local dealer. Also, be sure you have all the necessary tools and cabling before installing the RG300. -
Page 26: Cable Connections
AC Power Adapter Regular Phone To connect the RG300, follow these steps: Power on the RG300 by by first connecting the AC power adapter to the unit’s power socket, and then connecting the adapter to an AC power source. Use ONLY the power adapter supplied with the RG300. Otherwise, AUTION the product may be damaged. - Page 27 LAN port to an Ethernet switch or other device. Make sure the length of each cable does not exceed 100 meters (328 ft). If a PC is powered on, the RJ-45 LAN port LED on the RG300 will turn on to indicate a valid link.
-
Page 28: Initial Configuration
(Dynamic Host Configuration Protocol), you can connect immediately to the web management interface. Otherwise, you must first check if your PC’s IP address is set on the same subnet as the RG300 (that is, the PC’s IP address starts 192.168.1.x). -
Page 29: Home Page
“Administrator Settings” on page 32 to control management access to the unit. The home page displays the current status of the WiMAX connection. To configure basic settings for the current operating mode, click Basic Setup. For more information, see “Using the Basic Setup Wizard” on page Alternatively, to configure more detailed settings, click Advanced Setup. -
Page 30: Using The Basic Setup Wizard
Signal Quality – An indication of the carrier-to-interference-plus- ◆ noise-ratio (CINR), which measures the strength of the receive signal compared to other interference and noise. Connection Status – The current status of the WiMAX connection. ◆ Central Frequency – The center frequency of the WiMAX signal. ◆... -
Page 31: Figure 9: Confirm Settings
Figure 9: Confirm Settings Basic Setup Finished – When the Basic Setup steps are completed the unit reboots and attempts to connect to the specified WiMAX network. Log in again to return to the Home page. Figure 10: Setup Wizard Finished... -
Page 32: The Advanced Setup Menu
DVANCED ETUP The Advanced Setup menu provides access to all the configuration settings available for the RG300. Figure 11: Advanced Setup Each primary menu item is sumarized below with links to the relevant section in this guide where configuration parameters are described in detail: ◆... -
Page 33: Common Web
| Initial Configuration HAPTER Common Web Page Buttons OMMON UTTONS The web management interface includes some common buttons that are displayed at the top of each page. Figure 12: Common Web Page Buttons The list below describes these common buttons: Apply —... -
Page 34: Ection
ECTION ONFIGURATION This section provides details on configuring the RG300 using the web browser interface. This section includes these chapters: “System Settings” on page 30 ◆ “WAN Configuration” on page 38 ◆ “LAN Configuration” on page 44 ◆ “NAT Configuration” on page 47 ◆... -
Page 35: System Settings
YSTEM ETTINGS The RG300’s System menu allows you to perform general management functions for the unit, including setting the system time, configuring an access password, and upgrading the system software. The System configuration pages include the following options: ◆ “System Status” on page 31 “Administrator Settings”... -
Page 36: System Status
YSTEM TATUS The system status page displays connectivity status information for the unit’s WiMAX (WAN) and LAN interfaces, and the number of clients connected to the network. Figure 13: System Status – Internet Internet – Displays WAN (WiMAX) connection status: WAN IP –... -
Page 37: Administrator Settings
◆ password to be able to configure a new one. (Default: admin) If your RG300 unit is not configured with the standard default login Username/Password, use the default values on the label affixed to the unit. New Password – Enter a new administrator password. (Range: 3~12 ◆... -
Page 38: Firmware Upgrade
Upgrade – Downloads an operation code file from the web ◆ management station to the RG300 using HTTP. Use the Browse button to locate the code file locally on the management station and check the Reset Configuration to restore factory defaults. Click Apply to proceed. -
Page 39: Configuration Tools
| System Settings HAPTER Configuration Tools ONFIGURATION OOLS The Configurations Tools page allows you to restore factory default settings, or save and restore the unit’s configuration settings to or from a file on the management station. Figure 18: Configuration Tools The following parameters are displayed on this page: Restore Factory Default Configuration –... -
Page 40: System Time
HAPTER System Time YSTEM The RG300 uses the Simple Network Time Protocol (SNTP) to set its internal clock based on periodic updates from a time server. Maintaining an accurate time on the device enables the system log to record meaningful dates and times for event entries. -
Page 41: System Log
HAPTER System Log YSTEM The RG300 supports a logging process that controls error messages saved to memory. The logged messages serve as a valuable tool for isolating device and network problems. The System Log page displays the latest messages logged in chronological order, from the oldest to the newest. Log messages saved in the unit’s memory are erased when the device is... -
Page 42: Reset
| System Settings HAPTER Reset ESET The Reset page allows you to restart the device’s software. If the unit stops responding correctly or in some way stops functioning, performing a reset can clear the condition. Figure 22: Reset Unit Reset – Resets the unit. All current settings are retained. –... -
Page 43: Wan Configuration
WAN C ONFIGURATION The information in this chapter covers the configuration options for the RG300’s WAN connection. The WAN configuration pages include the following options: “WAN Settings” on page 39 ◆ “DNS” on page 42 ◆ “DDNS” on page 43 ◆... -
Page 44: Wan Settings
| WAN Configuration HAPTER WAN Settings WAN S ETTINGS Select the WAN connection type used by your service provider and specify DNS (Domain Name System) servers. Figure 23: WAN Settings The unit can be connected to your ISP in one of the following ways: DHCP IP Address –... -
Page 45: Dynamic Ip Address
| WAN Configuration HAPTER WAN Settings For dynamic IP assignment from the service provider, the unit functions as IP A YNAMIC DDRESS a Dynamic Host Configuration Protocol (DHCP) client. When enabled, no other settings are required. Figure 24: Dynamic IP Address Selecting Static IP Address for the WAN type enables you to enter static IP IP S TATIC... -
Page 46: L2Tp Settings
| WAN Configuration HAPTER WAN Settings If your service provider supports Layer 2 Tunneling Protocol (L2TP) for your L2TP S ETTINGS Internet connection, configure the settings described below. Figure 26: L2TP Settings The following parameters are displayed in this section on this page: Enable –... -
Page 47: Dns
| WAN Configuration HAPTER DNS (Domain Name System) server addresses are usually provided by service providers, however if you want to specify certain servers, the DNS page enables you to enter primary and secodary DNS addresses. Figure 28: DNS Settings The following parameters are displayed on this page: Primary DNS Address –... -
Page 48: Ddns
DDNS allows your domain name to follow your IP address automatically by changing your DNS records when your IP address changes. The RG300 provides access to a number DDNS service providers, such as DynDns.org, Easydns.com, and ZoneEdit.com. To set up an DDNS account, visit the website of one of the supported service providers. -
Page 49: Lan Configuration
LAN C ONFIGURATION The information in this chapter covers the configuration options for the RG300’s LAN functions. The LAN configuration pages include the following options: “LAN Settings” on page 45 ◆ “DHCP Client List” on page 46 ◆ – 44 –... -
Page 50: Lan Settings
LAN S ETTINGS The RG300 must have a valid IP address for management using a web browser and to support other features. The unit has a standard default IP address of 192.168.1.1. You can use this IP address or assign another address that is compatible with your existing local network. -
Page 51: Dhcp Client List
| LAN Configuration HAPTER DHCP Client List DHCP C LIENT The DHCP Client List page enables you to see the MAC address of devices that are currently connected to the unit and have been assigned an IP address by the DHCP server. Figure 31: DHCP Client List –... -
Page 52: Nat Configuration
NAT C ONFIGURATION The information in this chapter covers the configuration options for the RG300’s Network Address Translation (NAT) functions. The NAT configuration pages include the following options: “NAT Settings” on page 48 ◆ “Port Mapping” on page 49 ◆... -
Page 53: Nat Settings
Network Address Translation (NAT) is a standard method of mapping multiple “internal” IP addresses to one “external” IP address on devices at the edge of a network. For the RG300, the internal (local) IP addresses are the IP addresses assigned to local PCs by the DHCP server, and the external IP address is the IP address assigned to the WiMAX interface. -
Page 54: Port Mapping
◆ network. The specified address must be in the same subnet as the RG300 and its DHCP server address pool. Alternatively, the IP address can be set by selecting a PC from the DHCP client list. Use Client List – Allows the Private IP to be selected from the DHCP ◆... -
Page 55: Dmz
| NAT Configuration HAPTER If you have a client PC that cannot run an Internet application properly from behind the NAT firewall, you can open the client up to unrestricted two-way internet access by defining a virtual-DMZ (virtual-demilitarized- zone) host. Figure 34: DMZ Settings The following parameters are displayed on this page: Enable –... -
Page 56: Alg
| NAT Configuration HAPTER The RG300 supports the passthrough of three of the most commonly used VPN protocols; PPTP, L2TP, and IPsec, as well as VoIP SIP traffic. The VPN protocols allow remote users to establish a secure connection to their corporate network. -
Page 57: Firewall Configuration
IREWALL ONFIGURATION The information in this chapter covers the configuration options for the RG300’s firewall functions. The Firewall configuration pages include the following options: “Firewall Settings” on page 53 ◆ “Client Filtering” on page 54 ◆ “Port Filtering” on page 55 ◆... -
Page 58: Firewall Settings
The following parameters are displayed on this page: ◆ Enable – Enables all firewall features. Disallow PING from WAN side – Prevents pings on the unit’s WiMAX ◆ interface from being routed to the network. Allow Access WebUI from WAN – Allows a user to be able to log into ◆... -
Page 59: Client Filtering
| Firewall Configuration HAPTER Client Filtering LIENT ILTERING You can block access to the Internet from clients on the local network by specifying IP addresses and TCP/UDP port numbers. You can configure up to five IP filters on the unit. Figure 37: Client Filtering Settings The following parameters are displayed on this page: Target IP –... -
Page 60: Port Filtering
| Firewall Configuration HAPTER Port Filtering ILTERING Port filtering restricts connections to limit the risk of intrusion and can defend against a wide array of common hacker attacks. The port filtering feature allows the Gateway to block traffic for a specified schedule based on TCP/UDP ports. -
Page 61: Mac Filtering
| Firewall Configuration HAPTER MAC Filtering MAC F ILTERING You can block access to the Internet from clients on the local network based on MAC addresses. You can configure up to 20 MAC address filters on the unit. Figure 39: MAC Filtering The following parameters are displayed on this page: ◆... -
Page 62: Url Filtering
HAPTER URL Filtering URL F ILTERING The RG300 provides a method for blocking Internet access based on Uniform Resource Locator (URL) keywords. By filtering URLs accessed from the network, users can be prevented from reaching prohibited online content. Figure 40: URL Filtering The following items are displayed on this page: String —... -
Page 63: Host Filtering
| Firewall Configuration HAPTER Host Filtering ILTERING The RG300 provides a method for blocking Internet access based on web domains. A domain name is the name of a particular web site. For example, www.fungames.com. Figure 41: Host Filtering The following items are displayed on this page: Host String —... -
Page 64: Routing Configuration
OUTING ONFIGURATION The information in this chapter covers the configuration options for the RG300’s Routing functions. The Routing configuration pages include the following options: “Routing Table” on page 60 ◆ “Static Route” on page 61 ◆ – 59 –... -
Page 65: Routing Table
| Routing Configuration HAPTER Routing Table OUTING ABLE The Routing Table displays the list of static routes on the unit. Figure 42: Routing Table The following parameters are displayed in this section on this page: Route – The IP address that identifies the IP subnet of the remote ◆... -
Page 66: Static Route
| Routing Configuration HAPTER Static Route TATIC OUTE Static routes allow a manual method to set up routing between specific destination networks, subnetworks, or hosts. Static routes may be required to force the use of a specific route to a subnet. Static routes do not automatically change in response to changes in network topology, so only configure a small number of stable routes to ensure network accessibility. -
Page 67: Up N P Configuration
ONFIGURATION The information in this chapter covers the configuration options for the RG300’s Universal Plug and Play Forum (UPnP) feature. The UPnP configuration pages include the following options: “UPnP” on page 63 ◆ – 62 –... -
Page 68: Upnp Configuration Upnp
| UPnP Configuration HAPTER UPnP UPnP (Universal Plug and Play Forum) provides inter-connectivity between devices supported by the same standard. Figure 44: UPnP Setting The following parameters are displayed in this section on this page: UPnP – Enables UpnP support on the unit. ◆... -
Page 69: Oip Settings
You can make VoIP calls by connecting a regular phone to one of the RG300’s RJ-11 Phone ports. The RG300 allows up to two RJ-11 Phone ports to be configured separately with different settings. The VoIP configuration pages include the following options: ◆... -
Page 70: Sip Account
Outgoing Display Name — The name that is displayed to the other party during a call. The same with WiMAX Username and Password — Uses the ◆ WiMAX user name and password as the SIP user name and password. SIP Username — Enter your SIP user name. ◆ ◆... -
Page 71: Sip Settings
| VoIP Settings HAPTER SIP Settings SIP Registrar/Domain Name — Enter the IP address or server ◆ domain name of the SIP server. SIP Registrar Port — Enter the port associated with SIP server traffic. ◆ SIP Proxy Address/Domain Name — Address of the VoIP service ◆... -
Page 72: Speed Dial
| VoIP Settings HAPTER Speed Dial FAX — Selects the method to use when sending fax messages over the ◆ VoIP network from a fax machine connected to one of the RJ-11 Phone ports on the Gateway. FAX T.38 — The SIP protocol sets up the VoIP call, then the T.38 ■... -
Page 73: Dial Plan
| VoIP Settings HAPTER Dial Plan Dial-plan strings specify key sequences used for specific calling features (Transfer, New Call, 3-way conference), as well as defining call restriction filters. A dial plan can filter the number and pattern of digits that a user dials to reach a particular telephone number. - Page 74 | VoIP Settings HAPTER Dial Plan Table 5: Dial Plan Elements Element Example Description [125-8] Limits a dialed digit to specified values or a range of values. The example specifies that only digits 1, 2, 5, 6, 7, and 8 are permitted.
-
Page 75: Call Feature
HAPTER Call Feature EATURE The RG300 allows you to configure several call features, such as call waiting and call-forwarding. Other call features can be implemented by pressing specific phone buttons or entering dial patterns. Some call features may be dependent on support at the SIP server. - Page 76 | VoIP Settings HAPTER Call Feature caller ID when the transferee phone is ringing, but then shows the original calling party ID as soon as you hang up. Attended Transfer — During a call press the “Flash” button, which ■ puts the caller on hold, then enter the new call key sequence (as defined on the Dial Plan page;...
-
Page 77: Phone Settings
| VoIP Settings HAPTER Phone Settings HONE ETTINGS The Phone Settings page allows you to configure control features that affect a phone connected to a VoIP port. Figure 50: Phone Settings The following items are displayed on this page: Caller ID Block — Check this box to enable a block on the displayed ◆... -
Page 78: Codecs
The same codec must be supported at each end of a VoIP call to be able to encode and decode the signal. Since devices in other networks may want to use different codecs, the RG300 supports several common standards. Figure 51: VoIP Codecs The following items are displayed on this page: Codecs —... - Page 79 | VoIP Settings HAPTER Codecs buttons to set the priority. The Gateway attempts to use the codec highest in the list before trying the next lower one. – 74 –...
-
Page 80: I -F I Settings
ETTINGS The RG300 includes an IEEE 802.11n radio interface for local Wi-Fi communications. The Wi-Fi set up pages include configuration options for the radio signal characteristics and Wi-Fi security. The Wi-Fi configuration pages include the following options: ◆ “Basic Wireless Settings” on page 76 “Advanced Wireless Settings”... -
Page 81: Basic Wireless Settings
| Wi-Fi Settings HAPTER Basic Wireless Settings ASIC IRELESS ETTINGS From the WiFi menu, click on Basic to configure basic settings for the unit’s Wi-Fi radio interface. The unit’s radio can operate in six modes, IEEE 802.11b/g mixed, 802.11b only, 802.11g only, 802.11n only, 802.11g/n mixed, and 802.11b/g/n mixed. - Page 82 | Wi-Fi Settings HAPTER Basic Wireless Settings 11b/g/n Mixed: All 802.11b/g/n clients can communicate with the ■ Wi-Fi radio (up to 150 Mbps), but data transmission rates may be slowed to compensate for 802.11b/g clients. SSID — The name of the wireless network service provided by the Wi- ◆...
-
Page 83: Advanced Wireless Settings
| Wi-Fi Settings HAPTER Advanced Wireless Settings DVANCED IRELESS ETTINGS The Advanced Settings page includes additional parameters concerning the wireless network and Wi-Fi Multimedia settings. Figure 53: Advanced Wireless Settings The following items are displayed on this page: ◆ Beacon Period — The rate at which beacon signals are transmitted from the access point. -
Page 84: Wireless Security
802.11b clients. IRELESS ECURITY The RG300’s Wi-Fi interface is configured by default as an “open system,” which broadcasts a beacon signal including the configured SSID. Wireless clients with a configured SSID of “ANY” can read the SSID from the beacon, and automatically set their SSID to allow immediate connection to the wireless network. -
Page 85: Wired Equivalent Privacy (Wep)
RG300 and all its clients. OPEN — Open-system authentication accepts any client attempting ■ to connect the RG300 without verifying its identity. In this mode the default data encryption type is “WEP.” SHARED — The shared-key security uses a WEP key to ■... -
Page 86: Wpa Pre-Shared Key
Auth Mode — Configures the WPA-PSK and WPA2-PSK security modes ◆ used by clients. When using WPA-PSK or WPA2-PSK, be sure to define the shared key for the RG300 and all its clients. WPAPSK — Clients using WPA with a Pre-shared Key are accepted ■... - Page 87 | Wi-Fi Settings HAPTER Wireless Security WPAPSK/WPA2PSK mixed mode — Clients using WPA or WPA2 ■ with a Pre-shared Key are accepted for authentication. The default data encryption type is TKIP/AES. EncryptType — Selects the data encryption type to use. (Default is ◆...
-
Page 88: Acl Settings
ETTINGS Wireless clients can be authenticated for network access by checking their MAC address against a local database configured on the RG300. You can configure a list of up to 32 wireless client MAC addresses in the filter list to allow network access. -
Page 89: O S Configuration
ONFIGURATION The RG300 supports Quality of Service (QoS) settings that enable traffic rate limits to be set for all or specific LAN clients. The QoS configuration pages include the following options: “QoS Settings” on page 85 ◆ – 84 –... -
Page 90: Qos Settings
| QoS Configuration HAPTER QoS Settings ETTINGS From the QoS Settings page, you can set rate limits for outbound (WiMAX uplink) traffic from all or specified clients. Figure 58: QoS Settings The following parameters are displayed on this page: General — Sets QoS parameters that apply to all LAN clients (except ◆... -
Page 91: Ection
ECTION PPENDICES This section provides additional information and includes these items: “Troubleshooting” on page 87 ◆ “Hardware Specifications” on page 89 ◆ “Cables and Pinouts” on page 93 ◆ – 86 –... -
Page 92: A Troubleshooting
◆ correctly configured for TCP/IP. The IP settings should be set to “obtain an IP address automatically.” You may be out of the service area of the WiMAX network. Check with ◆ the WiMAX service provider for service coverage information. -
Page 93: Cannot Access Web Management
| Troubleshooting PPENDIX Cannot Access Web Management ANNOT CCESS ANAGEMENT If the management interface cannot be accessed using a web browser: Be sure the management station is correctly configured for TCP/IP. The ◆ IP settings should be set to “obtain an IP address automatically.” Try a Ping command from the management station to the unit’s IP ◆... -
Page 94: Specifications
RJ-45 connector, auto MDI/X: ETWORK NTERFACE 10BASE-T: RJ-45 (100-ohm, UTP cable; Category 3 or better) 100BASE-TX: RJ-45 (100-ohm, UTP cable; Category 5 or better) System: Power, WiMAX signal strength, WiFi, LED I NDICATORS Ports: Link/Activity Input: 100-240 VAC, 50-60 Hz, 0.5 A maximum... -
Page 95: Wimax Specifications
| Hardware Specifications PPENDIX WiMAX Specifications MAX S PECIFICATIONS Pattern: Omnidirectional NTENNAS Transmit and Receive: One transmit and two receive with Maximal-Ratio Combining (MRC). Support for transmitter diversity. Gain: 6 dBi Impedance: 50 Ohm FCC-2.5 GHz: 2496-2690 MHz PERATING REQUENCY Taiwan NCC-2.5 GHz: 2500-2690 MHz... -
Page 96: Wi-Fi Specifications
| Hardware Specifications PPENDIX Wi-Fi Specifications Adaptive jitter buffer, up to 200 milliseconds DTMF tone detection and generation Caller ID number and name EATURES Caller ID Block Call transfer Call waiting/hold/retrieve 3-way conference call Call blocking T.38 fax relay Dial plan Speed dial Call forwarding: No Answer/Busy/All 3 REN total in system... -
Page 97: Compliances
| Hardware Specifications PPENDIX Compliances OMPLIANCES FCC CFR 47 Part 15 Class B MISSIONS EN 55022 Class B EN 55024 Class B MMUNITY EN 301 489-1/4/17 US: 2.5 GHz - FCC CFR 47 Part 27M MAX R ADIO IGNAL CE: 2.3 GHz - EN 302 326 ERTIFICATION 2.5 GHz - EN 302 544 NCC: PLMN09... -
Page 98: Ables And Pinouts
ABLES AND INOUTS WISTED ABLE SSIGNMENTS For 10/100BASE-TX connections, a twisted-pair cable must have two pairs of wires. Each wire pair is identified by two different colors. For example, one wire might be green and the other, green with white stripes. Also, an RJ-45 connector must be attached to both ends of the cable. -
Page 99: Straight-Through Wiring
| Cables and Pinouts PPENDIX Twisted-Pair Cable Assignments Table 7: 10/100BASE-TX MDI and MDI-X Port Pinouts MDI Signal Name MDI-X Signal Name Transmit Data plus (TD+) Receive Data plus (RD+) Transmit Data minus (TD-) Receive Data minus (RD-) Receive Data plus (RD+) Transmit Data plus (TD+) Receive Data minus (RD-) Transmit Data minus (TD-) -
Page 100: Crossover Wiring
| Cables and Pinouts PPENDIX Twisted-Pair Cable Assignments If the twisted-pair cable is to join two ports and either both ports are ROSSOVER IRING labeled with an “X” (MDI-X) or neither port is labeled with an “X” (MDI), a crossover must be implemented in the wiring. Figure 61: Crossover Wiring EIA/TIA 568B RJ-45 Wiring Standard 10/100BASE-TX Crossover Cable... -
Page 101: Port
| Cables and Pinouts PPENDIX RJ-11 Port RJ-11 P Standard telephone RJ-11 connectors and cabling can be found in several common wiring patterns. These six-pin connectors can accommodate up to three wire pairs (three telephone lines), but usually only one or two pairs of conductor pins and wires are implemented. -
Page 102: Glossary
REQUENCY can be of different widths (the channel bandwidth) and the transmitted radio signal is spread across the full width of the channel. The range of frequencies occupied by a WiMAX radio signal. The amount of HANNEL ANDWIDTH information that can be transmitted in a radio signal is related to the channel bandwidth, which is measured in Megahertz (MHz). - Page 103 Extensible Authentication Protocol. An authentication protocol used to authenticate subscribers. EAP is used with TLS or TTLS authentication to provide “mutual authentication” between a subscriber and a WiMAX network. Hypertext Transfer Protocol. HTTP is a standard used to transmit and HTTP receive all data over the World Wide Web.
- Page 104 Scalable Orthogonal Frequency Division Multiple Access. The air interface SOFDMA defined for mobile WiMAX. SOFDMA is a multiple access method that allows simultaneous transmissions to and from several users, employing a subchannel structure that scales with bandwidth.
- Page 105 Subscriber Identity Module. A standard for a small removable integrated circuit card that securely stores information used to identify a mobile wireless subscriber. A general term for a customer’s WIMAX terminal equipment that provides UBSCRIBER TATION connectivity with a base station.
- Page 106 Access. The IEEE 802.16-2004 standard, known as “fixed WiMAX,” supports only point-to-point links and has no support for mobility. The IEEE 802.16e-2005 standard, known as “mobile WiMAX,” is an amendment to IEEE 802.16-2004 and supports mobility. Note that mobile WiMAX standard is not backward compatible with the fixed WiMAX standard.
-
Page 107: Index
NDEX AC power adapter factory defaults, restoring administrator password, setting firewall protection administrator settings firmware update Advanced Setup menu fixed-IP xDSL AES encryption fragmentation threshold authentication frequency setting type authentication options auto-logout time Gateway address gateway function beacon interval button, Reset hacker attack, prevention hardware, description cable assignments... - Page 108 NDEX open system WAN connection type operating frequency web management interface access login troubleshooting WEP security package checklist wireless network mode panels, front and rear Wizard, setup password, setting WPA pre-shared key phone settings ping discard port indicators power socket power supply, specifications PPTP private IP...
- Page 109 RG300 E042011-CS-R01 149100000095W...
Need help?
Do you have a question about the RG300 and is the answer not in the manual?
Questions and answers