Advertisement
Quick Links
Download this manual
See also:
User Manual
1, Introduction
Support and Service
Thanks for your choice for Minivet multi-axis aircraft, in order to make it
convenient and correct for you to use our product, please read the manual
carefully. If you face some difficulties when using products, please contact our
distributor or Wingsland Service Center by email or telephone.
Wingsland service center:
Email address:
service@szsungreen.com
Tel: 0086-0755-23123452
Danger: Incorrect operation may will casualties.
Warning: Incorrect operation will casualties or will harm human body.
Caution: Incorrect operation will cause harm with less possibility to user,
but with a risk of being injured.
2, Before Using Product (read the instructions before first flight)
Disclaimer & Warning
Attention please read this disclaimer carefully before starting your pilot
experience. Thank you for your using Wingsland product, you hereby agree
with and accept the terms of this disclaimer and it is believed that you have
Product manual
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Wingsland Minivet
Summary of Contents for Wingsland Minivet
- Page 1 1, Introduction Support and Service Thanks for your choice for Minivet multi-axis aircraft, in order to make it convenient and correct for you to use our product, please read the manual carefully. If you face some difficulties when using products, please contact our distributor or Wingsland Service Center by email or telephone.
- Page 2 Chinese version shall prevail in China domestic area, the English shall prevail in other countries and areas. Instructions & Cautions Ensure using with genuine Wingsland accessories to get most efficiently flight experience.
- Page 3 Please uninstall all propellers before your calibration or parameters setting. Ensure that you are familiar with your local laws, administrative rules and social habits and agree that you are solely responsible for your own conduct and content while you fly. ...
- Page 4 Discarding battery arbitrarily would cause a fire hazard, and may pollute the environment. Ensure that the usage of battery strictly abide by Wingsland User Manual. Limitation of Liability Wingsland accepts no liability for damages, injuries or any legal...
- Page 5 Damages, injuries or any legal responsibilities caused by using the third party alternation products or fake Wingsland products. Any loss caused by improper use in a strong magnetic field or in the bad environmental conditions(such as in the temperature higher than 40 degrees or below 0 degrees Celsius, and in the wind over force 4, etc.)
- Page 6 Install 6s AA Alkaline Battery into the battery compartment on the back of the Remote Controller. Pay attention to positive and negative. When using the remote controller, please put the antenna to figure 4 position (horizontal) to the left 4, The Remote Controller component name...
- Page 7 5, Remote Controller Minivet remote controller works with 2.4G frequency and 10 channels, not only can control aircraft, but also gimbal and camera, thus user can finish all performance operation without leaving remote controller. (1)Install Battery Remote controller uses 6 alkaline batteries. Open battery cap, fix them into remote controller, and cover back cap.
- Page 8 Warning: Do not mix new and old batteries together. (2)Remote Controller Operation 1Turning Remote Controller On and Off On: Press Power Button to turn on the remote controller, red status LED will blink. Off: Press Power Button to turn off the remote controller, red status LED goes out.
- Page 9 immediately. Warning: Check positions of antennas and switches before turning on remote controller. Warning: Turn on remote controller first before inserting flight battery, after taking out battery then turn off remote controller. L1 Mode Switches (3rd gear) L1-Middle: GPS Stabilization Mode, 2 situations below A In the outdoors with strong GPS signal (more than 6 satellites), GPS Stabilization Mode .
- Page 10 To be used control gimbal’ pitch (4) Trimming Button Trimming Button is used to adjust left and right control stick middle point, when control stick middle point is calibrated by a computer, trimming adjustment is no need .When control stick middle point is tilt and out of control by computer, Trimming Button will work.
- Page 11 computer, do not use Trimming Button to adjust middle point unless emergency conditions. Trimming Button is locked default thus users will not touch it carelessly. Trimming Button Unlock Methods: A Make sure aircraft is powered off B Remote controller is turned off C Press down 2 Trimming Buttons simultaneously D Powered on remote controller E When hearing beeping sound twice ,unlock trimming adjustment is finished.
- Page 12 from factory, but when changing remote controller or receiver, Compliance Version should start again. Methods below: A Aircraft is powered off B Remote controller is turned off C Press 2 Trimming Buttons simultaneously as the picture shows D Powered on remote controller E Once Power Status LED blinks quickly release the trimming button F Powered on aircraft G Remote controller Status LED stops blinking ,keep long light to finish compliance version.
- Page 13 hand controls up and down, forward and behind, left and right mean left spin and right spin. American hand Japan's hand...
- Page 14 When the aircraft fixed-point hovering will deviate from the hovering, neutral point need to recalibrate the remote control Using automatic return mode, must ensure that the return path and no obstacles around the landing site (7)Remote Controller Operation Mode(model1 and model2)Switch A Aircraft is powered off B Turn on remote controller C Press 4 trimming buttons simultaneously D A A beep shows Model2, twice beep show Model1 Caution: After switching models, suggest calibrating Throttle middle...
- Page 15 Icon arrange contents below Power LED Status Slid On Work Mode Quick Blink Compliance Version Sound Indicate Powering on remote controller with beep, remote controller start working, continuous deeps, over low voltage of remote controller, battery need to be replaced. Reduce trimming adjustment lock, a beep Start trimming adjustment lock, a beep Model2 and Model1 switches, a beep.Model2,beep twice,Moedel1.
- Page 16 Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ‐‐ Reorient or relocate the receiving antenna. ‐‐ Increase the separation between the equipment and receiver. ‐‐ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ‐‐ Consult the dealer or an experienced radio/TV technician for help. FCC RF warning statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Need help?
Do you have a question about the Minivet and is the answer not in the manual?
Questions and answers