Initial Set-Up With Mynice (Ios) Technology - Nice IT4WIFI Instructions And Warnings For Installation And Use

Table 3 - Smartphone with Android 5 operating system and
later versions
01. Open the "MyNice Welcome" app and select
"Start with your first Nice accessory"
02. After entering the values requested by the
app (Username, Description, Home), select
"Add new accessory..."
03.
After the WiFi networks have been scanned,
select the "NiceIT4WIFIxxxxxx" name to be
configured: xxxxxx denote the last 6 char-
acters of the MAC appearing on the IT4WIFI
label.
Select the arrow on the top right-hand side
to proceed
04. Enter the credentials for the network to which
the accessory must be connected.
It is important to carefully check that the pa-
rameters have been entered correctly.
After selecting the arrow on the top right-
hand side, wait roughly 2 minutes for the pro-
cedure to terminate

4.3 - Initial set-up with MyNice (iOS) technology

To run the procedure, you must be in the proximity of the IT4WIFI device, the L3 LED must be a steady green and the L2 LED flashing green.
Should this not be the case, run the Reset procedure (Chapter 8).
Moreover, ensure that the iPhone is connected to a Wi-Fi network that supports the Bonjour service.
Table 4 - iPhone with iOS 10.0 operating system and later
versions
01. Under "Settings" > "WiFi" on the iPhone, at
the bottom of the screen, select the "NiceIT-
4WIFIxxxxxx" name to be configured: xxxxxx
denote the last 6 characters of the MAC ap-
pearing on the IT4WIFI label. Follow the in-
structions proposed on the pages. Once
the IT4WIFI network access procedure ter-
minates, check that LEDs L3 and L2 are lit
steady green
02. Open the "MyNice Welcome" app and select
"Start with your first Nice accessory"
03.
After entering the values requested by the
app (Username, Description, Home), from
the list of accessories in the network, select
IT4WIFI and wait for the device to complete
the set-up procedure. At the end of the pro-
cedure, check that LEDs L1 and L3 are lit
steady green (LED L2 may remain orange if
the device cannot be reached remotely). Then
carry on
05. Once the procedure terminates, wait for the
accessory to appear in the app among the
Wi-Fi network accessories in which it was
configured and wait for LEDs L1 and L3 to
turn steady green (LED L2 may remain orange
if the device cannot be reached remotely).
Subsequently, select it to proceed
06. Enter the code stamped on the IT4WIFI label
and select the arrow on the top right-hand
side to complete the set-up procedure
Once the set-up terminates, to control the
07.
automation connected to the IT4WIFI device,
select the "Open", "Stop" and "Close" but-
tons. The change of status of the automation
can be viewed on the icon.
Selecting the "eye" symbol allows for the use
of all the additional movement controls
If the procedure described does not terminate successfully,
check that the requirements indicated at the beginning of the
manual are satisfied, run the IT4WIFI Reset procedure using the
P button (Chapter 8) and then try again.
To view other MyNice technology and "MyNice Welcome" app func-
tions, consult Chapter 6
04. Enter the code stamped on the IT4WIFI label
and select the arrow on the top right-hand
side to complete the set-up procedure
05.
Once the set-up terminates, to control the
automation connected to the IT4WIFI device,
select the "Open", "Stop" and "Close" but-
tons. The change of status of the automa-
tion can be viewed on the icon. Selecting the
"eye" symbol allows for the use of all the ad-
ditional movement controls
If the procedure described does not terminate successfully,
check that the requirements indicated at the beginning of the
manual are satisfied, run the IT4WIFI Reset procedure using the
P button (Chapter 8) and then try again.
To view other MyNice technology and "MyNice Welcome" app func-
tions, consult Chapter 6
English – 5