Bosch PMF 350 CES Original Instructions Manual page 17

OBJ_BUCH-2652-002.book Page 17 Wednesday, March 16, 2016 9:27 AM
Working without auxiliary handle
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-4:
2 2
Sanding: a =6 m/s , K=1.5 m/s
h
Sawing with plunge cut saw blade: a
Sawing with segment saw blade: a
2
Scraping: a =10 m/s , K=1.5 m/s
h
Working with auxiliary handle
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-4:
2 2
Sanding: a =5 m/s , K=1.5 m/s
h
Sawing with plunge cut saw blade: a
Sawing with segment saw blade: a
2
Scraping: a =12 m/s , K=1.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2009/125/EC (Regulation
1194/2012), 2011/65/EU, until 19 April 2016:
Selecting the Application Tool/Accessory
The following table shows examples for application tools. Further application tools can be found in the extensive Bosch acces-
sories program.
Accessory
BIM segment saw
blade
Base plate for sand-
ing, series Delta
93 mm
Bosch Power Tools
2004/108/EC, from 20 April 2016 on: 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60745-1, EN 60745-2-4, EN
50581.
2 2
=10 m/s , K=2 m/s
Technical file (2006/42/EC) at:
h
2 2
=10 m/s , K=3 m/s
Robert Bosch Power Tools GmbH, PT/ETM9,
h
2
.
70538 Stuttgart, GERMANY
Henk Becker
Executive Vice President
Engineering
2 2
=13 m/s , K=3 m/s
h
2 2
=12 m/s , K=3 m/s
h
2
.
Robert Bosch Power Tools GmbH
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
Assembly
Changing the Tool
 Before any work on the machine itself, pull the mains
 Wear protective gloves when changing application
Please observe the application tools/accessories intended
for your tool.
Accessory
Material Application
Wooden materials, Separating and plunge cuts; also for sawing close to edges,
Plastic, in corners and hard to reach areas;
Non-ferrous metals example: shortening already installed bottom rails or door
hinges, plunge cuts for adjusting floor panels
Depends on sanding sheet Sanding surfaces close to edges, in corners or hard to reach
areas;
depending on the sanding sheet for, e.g., sanding wood,
paint, varnish, stone
Fleeces for cleaning and for texturing wood, removing rust
from metal and for keying varnishes, polishing felt for pre-
polishing
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
plug.
tools/accessories. Contact with the application tool/
accessory can lead to injuries.
English | 17
PMF 350 CES
1 609 92A 2T2 | (16.3.16)