Advertisement
Quick Links
OWNER'S MANUAL
MicroSub+ / PowerWedge+
Amplified Subwoofer Systems with DCD™ Amplifier Technology
Thank you for purchasing a JL Audio amplified subwoofer system for
your automotive sound system.
Your subwoofer system has been designed and manufactured to exacting
standards to provide high-quality sub-bass performance and years of
musical enjoyment in your vehicle. For maximum performance, we
highly recommend that you have your new subwoofer system installed
by an authorized JL Audio retailer. Your authorized retailer has the
necessary training, expertise and installation equipment to ensure
optimum performance from this product. Should you decide to install
your subwoofer system yourself, please take the time to read this manual
thoroughly so as to familiarize yourself with it installation requirements
If you have any questions regarding the instructions in this
manual or any aspect of your subwoofer system's operation, please contact
your authorized JL Audio retailer for assistance. If you need further
assistance, please call the JL Audio Technical Support Department at
(954) 443-1100 during business hours.
Low-Pass
Input
Filter Freq. (Hz)
Sensitivity
Turn-On
Output
100
125
Mode
Polarity
80
Signal | DC | Rem
0 | 180 deg.
Min.
Max.
50
200
Power
Protect
(green)
(red)
Remote
Level
Control
(L)
(R)
Power Connections
+12 VDC
GND
Remote
and setup procedures.
Advertisement
Related Manuals for JL Audio MicroSub+
Summary of Contents for JL Audio MicroSub+
- Page 1 Remote MicroSub+ / PowerWedge+ Amplified Subwoofer Systems with DCD™ Amplifier Technology Thank you for purchasing a JL Audio amplified subwoofer system for your automotive sound system. Your subwoofer system has been designed and manufactured to exacting standards to provide high-quality sub-bass performance and years of musical enjoyment in your vehicle.
- Page 2 4. Find a good, solid metal grounding point ABOUT DCD™ TECHNOLOGY close to the amplifier panel and connect the JL Audio’s exclusive DCD™ amplifier technology negative power wire to it using appropriate combines direct power conversion with an ultra- hardware. Use the same sized wire used...
- Page 3 inputs of the amplifier. The amplifier’s POWER CONNECTIONS PLUG input section automatically sums stereo To connect the power wires and remote signals to mono for the internal amplifier turn-on wire to the amplifier, unplug the section. When feeding a single, low-level “Power Connections”...
- Page 4 When the protection mode is activated, the amplifier outputs are muted to protect its circuitry. When the amplifier cools, Power Protect the amplifier will return to its normal operation (green) (red) and the LED will turn green. Remote JL AUDIO ®...
- Page 5 Enclosure Specifications RMS Power Nominal Model Driver(s) @ 14.4V, Dimensions Impedance <1% THD+N 18.5 in x 11.125 in x 5.125 in ACP108LG-W3v3 (1) 8W3v3-0.40 0.40 Ω 250 W 470 mm x 283 mm x 130 mm 36.625 in x 11.125 in x 5.125 in ACP208LG-W3v3 (2) 8W3v3-0.40 0.20 Ω...
- Page 6 Care should be taken to securely mount this control in a manner that does not interfere with the vehicle’s operation. When setting the amplifier’s input sensitivity, the Remote Level Control should be unplugged or at full clockwise rotation (maximum level). JL AUDIO ®...
-
Page 7: Troubleshooting
TROUBLESHOOTING Problem Possible Cause Solution How to properly set Please refer to Appendix A to set the input sensitivity for input sensitivity maximum, low-distortion output. Remove fuse and check with continuity meter. Replace if Faulty fuse necessary. Poor connection Check “+12 VDC”, “GND”, and “Remote”... - Page 8 LIMITED WARRANTY - AMPLIFIED SUBWOOFER SYSTEMS (USA) JL Audio warrants this product to be free of defects in materials and workmanship for a period of two (2) years from the original date of purchase. This warranty is not transferable and applies only to the original purchaser from an authorized JL Audio dealer.