Page 1 Journey 2 0 1 8 O W N E R ’ S M A N U A L...
Page 2 VEHICLES SOLD IN CANADA This manual illustrates and describes the operation of With respect to any Vehicles Sold in Canada, the name features and equipment that are either standard or op- FCA US LLC shall be deemed to be deleted and the name tional on this vehicle.
Page 3 TABLE OF CONTENTS SECTION PAGE INTRODUCTION ..............3 GRAPHICAL TABLE OF CONTENTS .
Page 5: Table Of Contents
INTRODUCTION CONTENTS INTRODUCTION ......4 WARNINGS AND CAUTIONS ....6 HOW TO USE THIS MANUAL .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION versions are not expressly indicated in the text. Therefore, you should only consider the information which is related Dear Customer, to the trim level, engine, and version that you have Congratulations on selecting your new vehicle. Be assured purchased.
Page 7: Symbols
INTRODUCTION 5 Symbols Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustra- Consult the following table for a description of the symbols tions may differ from your vehicle’s equipment. that may be used on your vehicle or throughout this The detailed index at the back of this Owner’s Manual Owner’s Manual: contains a complete listing of all subjects.
Page 8: Warnings And Cautions
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against oper- ating procedures that could result in a collision, bodily injury and/or death. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owner’s Manual, you may miss important information.
Page 9 GRAPHICAL TABLE OF CONTENTS CONTENTS FRONT VIEW ......8 INSTRUMENT PANEL .....10 REAR VIEW .
Page 10: Front View
8 GRAPHICAL TABLE OF CONTENTS FRONT VIEW Front View 1 — Headlights 4 — Wheels/Tires 2 — Hood/Engine Compartment 5 — Exterior Mirrors 3 — Windshield 6 — Doors...
Page 11: Rear View
GRAPHICAL TABLE OF CONTENTS 9 REAR VIEW Rear View 1 — Rear Lights 2 — Rear Windshield Wiper 3 — Liftgate...
Page 12: Instrument Panel
10 GRAPHICAL TABLE OF CONTENTS INSTRUMENT PANEL Instrument Panel 1 — Air Vents 4 — Windshield Wiper Lever (Behind Steering Wheel) 2 — Multifunction Lever (Behind Steering Wheel) 5 — Radio 3 — Instrument Cluster 6 — Steering Wheel...
Page 13: Interior
GRAPHICAL TABLE OF CONTENTS 11 INTERIOR Interior 1 — Door Locks/Window Switches 4 — Switch Panel 2 — Seats 5 — Climate Controls 3 — Gear Selector 6 — Glove Compartment...
Page 15 GETTING TO KNOW YOUR VEHICLE CONTENTS KEYS ....... . .17 SENTRY KEY .
Page 16 14 GETTING TO KNOW YOUR VEHICLE ▫ Keyless Enter-N-Go — Passive Entry ▫ Rear Head Restraint Removal ....56 (If Equipped) ......33 STEERING WHEEL .
Page 17 GETTING TO KNOW YOUR VEHICLE 15 ▫ High Beam/Low Beam Select Switch ..65 ▫ Automatic Climate Controls Overview..86 ▫ Flash-To-Pass ......65 ▫...
Page 18 16 GETTING TO KNOW YOUR VEHICLE ▫ Closing ......109 ▫ General Information .....120 LIFTGATE .
Page 19: Keys
GETTING TO KNOW YOUR VEHICLE 17 KEYS Key Fob Your vehicle uses a keyless ignition system. The ignition system consists of a key fob with Remote Keyless Entry (RKE) and a START/STOP push button ignition system. The Remote Keyless Entry system consists of a key fob and Keyless Enter-N-Go feature if equipped.
Page 20 18 GETTING TO KNOW YOUR VEHICLE NOTE: Driving at speeds 5 MPH (8 km/h) and above All doors can be programmed to unlock on the first push of disables the system from responding to all key fob buttons the unlock button. Refer to “Uconnect Settings” in “Multi- for all key fobs.
Page 21 GETTING TO KNOW YOUR VEHICLE 19 To Lock The Doors And Liftgate Using The Panic Alarm Push and release the lock button on the key fob to lock all To turn the Panic Alarm feature on or off, push the Panic doors and liftgate.
Page 22 20 GETTING TO KNOW YOUR VEHICLE NOTE: 2. Insert the tip of the emergency key or a #2 flat blade screwdriver into the slot and gently pry the two halves • Perchlorate Material — special handling may apply. See of the key fob apart. Make sure not to damage the seal www.dtsc.ca.gov/hazardouswaste/perchlorate during removal.
Page 23: Ignition Switch
GETTING TO KNOW YOUR VEHICLE 21 battery with your fingers. Skin oils may cause battery NOTE: Changes or modifications not expressly approved deterioration. If you touch a battery, clean it with by the party responsible for compliance could void the rubbing alcohol.
Page 24 22 GETTING TO KNOW YOUR VEHICLE NOTE: If the ignition switch does not change with the The push button ignition can be placed in the following push of a button, the key fob may have a low or dead modes: battery.
Page 25: Ignition Or Accessory On Message
GETTING TO KNOW YOUR VEHICLE 23 Ignition Or Accessory On Message WARNING! (Continued) Opening the driver’s door when the ignition is in ACC or • Never leave children alone in a vehicle, or with ON (engine not running), a chime will sound to remind access to an unlocked vehicle.
Page 26: Remote Start - If Equipped
24 GETTING TO KNOW YOUR VEHICLE REMOTE START — IF EQUIPPED WARNING! (Continued) How To Use Remote Start • Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others All of the following conditions must be met before the could be seriously or fatally injured.
Page 27: Remote Start Abort Message
GETTING TO KNOW YOUR VEHICLE 25 To Enter Remote Start Mode WARNING! Push and release the remote start button on the key fob • Do not start or run an engine in a closed garage or twice within five seconds. The vehicle doors will lock, the confined area.
Page 28: To Exit Remote Start Mode Without Driving The Vehicle
26 GETTING TO KNOW YOUR VEHICLE To Exit Remote Start Mode Without Driving The The Remote Start Comfort System can be activated and Vehicle deactivated through the Uconnect system. Refer to “Uconnect Settings” in “Multimedia” for further informa- Push and release the remote start button one time or allow tion on Remote Start Comfort System operation.
Page 29: Sentry Key
GETTING TO KNOW YOUR VEHICLE 27 SENTRY KEY If the vehicle security light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it The Sentry Key Immobilizer system prevents unauthorized indicates that there is a fault in the electronics. Should this vehicle operation by disabling the engine.
Page 30: Replacement Keys
28 GETTING TO KNOW YOUR VEHICLE Replacement Keys General Information The following regulatory statement applies to all radio NOTE: Only key fobs that are programmed to the vehicle frequency (RF) devices equipped in this vehicle: electronics can be used to start and operate the vehicle. Once a key fob is programmed to a vehicle, it cannot be This device complies with Part 15 of the FCC Rules and programmed to any other vehicle.
Page 31: To Arm The System
GETTING TO KNOW YOUR VEHICLE 29 To Disarm The System turn on, the park lamps and/or turn signals will flash, and the vehicle security light in the instrument cluster will The vehicle security alarm can be disarmed using any of flash.
Page 32: Rearming Of The System
30 GETTING TO KNOW YOUR VEHICLE NOTE: after 3 minutes, turn all of the visual signals off after 15 additional minutes, and then the vehicle security alarm • The driver’s door key cylinder and the liftgate button on will rearm itself. the key fob cannot arm or disarm the vehicle security alarm.
Page 33 GETTING TO KNOW YOUR VEHICLE 31 WARNING! • For personal security and safety in the event of a collision, lock the vehicle doors before you drive as well as when you park and leave the vehicle. • When leaving the vehicle, always remove the key fob from the vehicle and lock your vehicle.
Page 34: Power Door Locks
32 GETTING TO KNOW YOUR VEHICLE Power Door Locks Turning off the ignition or closing the door will allow the locks to operate. If a door is open, and the ignition is in the A power door lock switch is on each front door trim panel. ON/RUN or ACC position, a chime will sound as a Use this switch to lock or unlock the doors and liftgate.
Page 35: Keyless Enter-N-Go - Passive Entry (If Equipped)
GETTING TO KNOW YOUR VEHICLE 33 To change the current setting, refer to “Uconnect Settings” • The key fob may not be detected by the vehicle passive in “Multimedia” for further information. entry system if it is located next to a mobile phone, laptop, or other electronic device;...
Page 36 34 GETTING TO KNOW YOUR VEHICLE NOTE: If “Unlock All Doors 1st Press” is programmed all Preventing Inadvertent Locking Of Passive Entry Key doors will unlock when you grab hold of the driver’s front Fob In Vehicle: door handle. To select between “Unlock Driver Door 1st To minimize the possibility of unintentionally locking a Press”...
Page 37 GETTING TO KNOW YOUR VEHICLE 35 To Enter The Liftgate: To Lock The Vehicle’s Doors: With a valid Passive Entry key fob within 5 ft (1.5 m) of the With one of the vehicle’s Passive Entry key fobs within 5 ft liftgate, push the button underneath the left side of the (1.5 m) of the driver or passenger front door handle, push accent bar, which is located on the liftgate below the glass,...
Page 38 36 GETTING TO KNOW YOUR VEHICLE Do NOT grab the door handle, when pushing the door NOTE: handle button. This could unlock the door(s). • After pushing the door handle button, you must wait two seconds before you can lock or unlock the doors, using either Passive Entry door handle.
Page 39: Child-Protection Door Lock System - Rear Doors
GETTING TO KNOW YOUR VEHICLE 37 Child-Protection Door Lock System — Rear Doors To Engage The Child-Protection Door Lock System To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a Child- Protection Door Lock system.
Page 40 38 GETTING TO KNOW YOUR VEHICLE WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the Child-Protection locks are en- gaged. Failure to follow this warning may result in serious injury or death.
Page 41: Seats
GETTING TO KNOW YOUR VEHICLE 39 SEATS Manual Adjustment (Front Seats) Seats are a part of the Occupant Restraint System of the WARNING! vehicle. • Adjusting a seat while the vehicle is moving is WARNING! dangerous. The sudden movement of the seat could cause you to lose control.
Page 42 40 GETTING TO KNOW YOUR VEHICLE Forward/Rearward Adjustment While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once the desired For models equipped with manual seats, the driver and position has been reached.
Page 43 GETTING TO KNOW YOUR VEHICLE 41 Driver’s Seat Height Adjustment — If Equipped Recliner Adjustment The seat height control lever is located on the outboard side The recline lever is located on the outboard side of the seat. of the seat. Raise the lever to raise the seat. Lower the lever To recline the seat, lean forward slightly, lift the lever, lean to lower the seat.
Page 44: Manual Adjustment (Rear Seats)
42 GETTING TO KNOW YOUR VEHICLE WARNING! WARNING! • Adjusting a seat while the vehicle is moving is • It is extremely dangerous to ride in a cargo area, dangerous. The sudden movement of the seat could inside or outside of a vehicle. In a collision, people cause you to lose control.
Page 45 GETTING TO KNOW YOUR VEHICLE 43 Recliner Adjustment WARNING! The recline lever is on the outboard side of the seat. To • Adjusting a seat while the vehicle is moving is recline the seatback, lean back, lift the lever, position the dangerous.
Page 46: Power Adjustment (Front Seat)
44 GETTING TO KNOW YOUR VEHICLE Forward And Rearward Adjustment WARNING! The control lever is on the outboard side of the seat. Lift the Adjusting a seat while the vehicle is moving is dan- lever to move the seat forward or rearward. Release the gerous.
Page 47 GETTING TO KNOW YOUR VEHICLE 45 Adjusting The Seat Forward Or Rearward WARNING! The seat can be adjusted both forward and rearward. Push • Adjusting a seat while driving may be dangerous. the seat switch forward or rearward, and the seat will Moving a seat while driving could result in loss of move in the direction of the switch.
Page 48: Front Heated Seats - If Equipped
46 GETTING TO KNOW YOUR VEHICLE Front Heated Seats — If Equipped Power Lumbar — If Equipped The Power Lumbar switch is located on the outboard side The front heated seats control buttons are located within of the driver’s seat. Push the switch forward to increase the the Uconnect system.
Page 49: Manual Folding Second Row Seat
GETTING TO KNOW YOUR VEHICLE 47 Manual Folding Second Row Seat Vehicles Equipped With Remote Start On models that are equipped with remote start, the heated To Fold The Seat seats can be programmed to come on during a remote start. 1.
Page 50: Stadium Tip 'N Slide (Easy Entry/Exit Seat) - Seven Passenger Models
48 GETTING TO KNOW YOUR VEHICLE 2. Place one hand on the seatback and apply a gentle To Unfold The Seat pressure. Raise the seatback and lock it in place. 3. Lift the control lever with the other hand, allow the WARNING! seatback to move forward slightly, and then release the lever.
Page 51 GETTING TO KNOW YOUR VEHICLE 49 Move the control lever on the upper outboard side of the seatback forward. Then, in one fluid motion, the seat cushion flips upward and the seat moves forward on its tracks. Tip ’n Slide Seat NOTE: A hand-grip is molded into the front of each quarter trim panel near the door opening to assist entry and exit from the third-row passenger seats.
Page 52: Manual Folding Third Row Seats
50 GETTING TO KNOW YOUR VEHICLE To Unfold And Move The Second-Row Passenger Seat NOTE: Prior to folding the third-row passenger seatback, Rearward make sure the second-row passenger seatback is not in a reclined position. This will allow the seatback to fold easily. Move the seatback rearward until it locks in place and then continue sliding the seat rearward on its tracks until it To Fold The Seatback...
Page 53 GETTING TO KNOW YOUR VEHICLE 51 NOTE: You may experience deformation in the seat cush- The seatback can also be locked in the reclined position. To ion from the seat belt buckles if the seats are left folded for do so, pull the latch release-loop located at the top of the an extended period of time.
Page 54: Seatback/Armrest - Second Row Passenger Seat
52 GETTING TO KNOW YOUR VEHICLE Seatback/Armrest — Second Row Passenger Seat WARNING! The latch release-loop is located at the top of the seatback/ Keep the latch clean and free of objects and be certain armrest. Pull the release-loop forward to release the latch that the seatback/armrest is locked securely into posi- and then downward to lower the seatback/armrest.
Page 55: Supplemental Active Head Restraints (Ahr) - Front Seats
GETTING TO KNOW YOUR VEHICLE 53 Supplemental Active Head Restraints (AHR) — To raise the head restraint, pull upward on the head Front Seats restraint. To lower the head restraint, push the adjustment button, located at the base of the head restraint, and push Supplemental Active Head Restraints are passive, deploy- downward on the head restraint.
Page 56 54 GETTING TO KNOW YOUR VEHICLE For comfort, the Active Head Restraints can be tilted forward and backward. To tilt the head restraint closer to the back of your head, pull forward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head.
Page 57: Rear Head Restraint Adjustment
GETTING TO KNOW YOUR VEHICLE 55 Rear Head Restraint Adjustment WARNING! The second row seats are equipped with adjustable and • All occupants, including the driver, should not oper- removable head restraints. To raise the head restraint, pull ate a vehicle or sit in a vehicle’s seat until the head upward on the head restraint.
Page 58: Rear Head Restraint Removal
56 GETTING TO KNOW YOUR VEHICLE NOTE: For proper routing of a Child Seat Tether, refer to WARNING! “Occupant Restraints” in “Safety”. A loose head restraint thrown forward in a collision or WARNING! hard stop could cause serious injury or death to occu- pants of the vehicle.
Page 59: Heated Steering Wheel - If Equipped
GETTING TO KNOW YOUR VEHICLE 57 WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death.
Page 60: Mirrors
58 GETTING TO KNOW YOUR VEHICLE The heated steering wheel control button is located within WARNING! the Uconnect system. You can gain access to the control button through the climate screen or the controls screen. • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, •...
Page 61: Electrochromic Mirror - If Equipped
GETTING TO KNOW YOUR VEHICLE 59 Electrochromic Mirror — If Equipped NOTE: A single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the A single ball joint mirror is provided in the vehicle. It is a windshield.
Page 62: Outside Mirrors
60 GETTING TO KNOW YOUR VEHICLE Outside Mirrors To receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic and a slight overlap of the view obtained from the inside mirror. NOTE: The passenger side convex outside mirror will give a much wider view to the rear, and especially of the lane next to your vehicle.
Page 63: Interior Observation Mirror
GETTING TO KNOW YOUR VEHICLE 61 Outside Mirrors Folding Feature NOTE: From the “observation mirror” position, the door can only be closed. All outside mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have To return to the full open position, the door must first be three detent positions: closed and then opened by pushing the latch again to...
Page 64: Power Mirrors
62 GETTING TO KNOW YOUR VEHICLE Power Mirrors Models With Express Window Feature The power mirror switch is located on the driver’s door Push and release the mirror select button marked L (left) or trim panel. R (right). Then, push one of the four arrow buttons to move the mirror in the direction the arrow is pointing.
Page 65: Illuminated Vanity Mirrors - If Equipped
GETTING TO KNOW YOUR VEHICLE 63 • The mirrors come out of the unfolded position. • The mirrors shake and vibrate at normal driving speeds. To reset the power folding mirrors: fold and unfold them by pushing the button. (this may require multiple button pushes).
Page 66: Exterior Lights
64 GETTING TO KNOW YOUR VEHICLE Sun Visor “Slide-On-Rod” Feature — If Equipped The sun visor “Slide-On-Rod” feature allows for additional flexibility in positioning the sun visor to block out the sun. 1. Fold down the sun visor. 2. Unclip the visor from the center clip. 3.
Page 67: Daytime Running Lights (Drl)
GETTING TO KNOW YOUR VEHICLE 65 NOTE: The daytime running lights can be turned on and off using the Uconnect System, refer to “Uconnect Settings” in “Multimedia” for further information. High Beam/Low Beam Select Switch Pull the multifunction lever toward you to switch the headlights to high beam.
Page 68: Headlights On With Wipers (Available With Automatic Headlights Only)
66 GETTING TO KNOW YOUR VEHICLE Refer to “Uconnect Settings” in “Multimedia” for further To activate the delay feature, turn OFF the ignition switch information. while the headlights are still on. Then, turn off the head- lights within 45 seconds. The delay interval begins when To turn the automatic system off, move the headlight the headlight switch is turned off.
Page 69: Fog Lights - If Equipped
GETTING TO KNOW YOUR VEHICLE 67 Fog Lights — If Equipped NOTE: The fog lights will operate when the low beam headlights or parking lights are on. However, selecting the The front fog light switch is built into the headlight switch. high beam headlights will turn off the fog lights.
Page 70: Interior Lights
68 GETTING TO KNOW YOUR VEHICLE INTERIOR LIGHTS Courtesy/Interior Lighting The interior lights come on when a door is opened. To protect the battery, the interior lights will turn off automatically 10 minutes after the ignition is moved to the LOCK position.
Page 71: Wipers And Washers
GETTING TO KNOW YOUR VEHICLE 69 Parade Mode (Daytime Brightness Feature) The front wipers are operated by rotating a switch, located at the end of the lever. For information on using the rear Rotate the dimmer control upward to the first detent. This window wiper/washer, refer to “Rear Wiper Operation”...
Page 72 70 GETTING TO KNOW YOUR VEHICLE NOTE: The wipers will automatically return to the “park” Intermittent Wiper System position if you turn OFF the ignition switch while they are Use the intermittent wiper system when weather condi- operating. The wipers will resume operation when you tions make a single wiping cycle, with a variable pause turn the ignition switch back to the ON position.
Page 73 GETTING TO KNOW YOUR VEHICLE 71 There are five delay settings, which allow you to regulate WARNING! the wipe interval from a minimum of one cycle every two seconds to a maximum of approximately 36 seconds be- Sudden loss of visibility through the windshield could tween cycles at vehicle speeds below 10 mph (16 km/h).
Page 74: Rear Window Wiper/Washer
72 GETTING TO KNOW YOUR VEHICLE Rear Window Wiper/Washer Rotate the switch upward to the first detent position for rear wiper operation. The rear window wiper/washer control is located on the left side of the steering column. Rotate the switch upward past the first detent position to activate the rear washer.
Page 75 GETTING TO KNOW YOUR VEHICLE 73 If the rear wiper is operating when the ignition is turned to CAUTION! (Continued) the LOCK position, the wiper will automatically return to • In cold weather, always turn off the wiper switch and the “park”...
Page 76: Climate Controls
74 GETTING TO KNOW YOUR VEHICLE CLIMATE CONTROLS Manual Climate Control Overview The air conditioning and heating system is designed to make you comfortable in all types of weather. This system can be operated through either the instrument panel or through the Uconnect system display.
Page 77 GETTING TO KNOW YOUR VEHICLE 75 Manual Temperature Controls — Buttons On The Faceplate Uconnect 3/3 NAV with 8.4–inch display Manual Dual Zone Temperature Controls...
Page 78 76 GETTING TO KNOW YOUR VEHICLE Manual Climate Control Descriptions Icon Description MAX A/C Button Press to change the current setting, the indicator illuminates when MAX A/C is on. Pressing the button again turns the MAX A/C operation to switch into manual mode and the MAX A/C in- dicator turn offs.
Page 79 GETTING TO KNOW YOUR VEHICLE 77 Icon Description SYNC Button — If Equipped Press the SYNC button on the touchscreen to toggle the SYNC feature on/off. The SYNC indica- tor is illuminated when this feature is enabled. SYNC is used to synchronize the rear passenger temperature setting with the driver temperature setting.
Page 80 78 GETTING TO KNOW YOUR VEHICLE Icon Description Floor Mode Floor Mode Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Mix Mode Mix Mode Air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield.
Page 81 GETTING TO KNOW YOUR VEHICLE 79 Icon Description • Recirculation can be used in all modes except for Defrost. • The A/C can be deselected manually without disturbing the mode control selection. Front Defrost Setting Turn the Mode Control knob to the Front Defrost position. Air comes from the windshield and side window demist outlets.
Page 82 80 GETTING TO KNOW YOUR VEHICLE Economy Mode outboard rear seating position. The system provides heated air through the floor outlets or cool, dehumidified air If ECONOMY mode is desired, push the A/C button to through the headliner outlets. turn off the LED indicator and the A/C compressor. Rotate the temperature control knob to the desired temperature.
Page 83 GETTING TO KNOW YOUR VEHICLE 81 Rear Lock • Pressing the Rear Temperature Lock button on the touchscreen on the Uconnect touchscreen, illuminates a lock symbol in the rear display. The rear temperature and air source are controlled from the front Uconnect system.
Page 84 82 GETTING TO KNOW YOUR VEHICLE Icon Description Rear Lock Button Press and release to lock out the rear manual temperature controls from adjusting the rear tem- perature and blower settings. Front Climate Button Press and release this button to change the display on the Uconnect radio back to the Front Cli- mate Controls.
Page 85 GETTING TO KNOW YOUR VEHICLE 83 Icon Description Panel Mode Panel Mode Press this button on the touchscreen to change the air distribution mode to Panel Mode. In Panel Mode, air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air.
Page 86 84 GETTING TO KNOW YOUR VEHICLE Rear Manual Temperature Control Rear MTC Control Knobs Icon Description Panel Mode Panel Mode Air comes from the outlets in the headliner. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vanes of the outlets to one side will shut off the airflow.
Page 87 GETTING TO KNOW YOUR VEHICLE 85 Icon Description Bi-Level Mode Bi-Level Mode Air comes from both the headliner outlets and the floor outlets. NOTE: In many temperature positions, the Bi-Level mode is designed to provide cooler air out of the headliner outlets and warmer air from the floor outlets. Floor Mode Floor Mode Air comes from the floor outlets.
Page 88: Automatic Climate Controls Overview
86 GETTING TO KNOW YOUR VEHICLE Automatic Climate Controls Overview Radio 4.3 Automatic 3 Zone Temperature Controls Uconnect 3/3 NAV Automatic 3 Zone Temperature Controls...
Page 89 GETTING TO KNOW YOUR VEHICLE 87 Automatic Temperature Controls — Buttons On The Faceplate Automatic Climate Controls Descriptions Icon Description MAX A/C Button Press to change the current setting, the indicator illuminates when MAX A/C is on. Pressing it again turns the MAX A/C operation to switch into manual mode and the MAX A/C indicator turns off.
Page 90 88 GETTING TO KNOW YOUR VEHICLE Icon Description Recirculation Button Press and release this button on the touchscreen, or push the button on the faceplate, to change the system between recirculation mode and outside air mode. Recirculation can be used when outside conditions such as smoke, odors, dust, or high humidity are present.
Page 91 GETTING TO KNOW YOUR VEHICLE 89 Icon Description REAR CLIMATE Rear Climate Control Button Press and release this button to access the rear climate controls. The indicator will illuminate when the rear climate controls are ON. Driver And Passenger Temperature Up And Down Buttons Provides the driver and passenger with independent temperature control.
Page 92 90 GETTING TO KNOW YOUR VEHICLE Icon Description Faceplate Knob Blower Control Blower Control is used to regulate the amount of air forced through the climate system. There are seven blower speeds available. The speeds can be selected using either the blower control knob on the faceplate or the buttons on the touchscreen.
Page 93 GETTING TO KNOW YOUR VEHICLE 91 Icon Description Floor Mode Floor Mode Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Mix Mode Mix Mode Air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield.
Page 94 92 GETTING TO KNOW YOUR VEHICLE outboard rear seating position. The system provides heated CAUTION! air through the floor outlets or cool, dehumidified air through the headliner outlets. The rear system temperature Failure to follow these cautions can cause damage to control buttons are located in the Uconnect system, located the heating elements: on the instrument panel.
Page 95 GETTING TO KNOW YOUR VEHICLE 93 • To return to Front screen, press the FRONT CLIMATE button. Uconnect 3/3 NAV Automatic Rear Climate Buttons On The Touchscreen Uconnect 4.3 Automatic Rear Climate Buttons On The Touchscreen Icon Description Rear Auto Button Automatically controls the rear interior cabin temperature by adjusting airflow distribution and amount.
Page 96 94 GETTING TO KNOW YOUR VEHICLE Icon Description Front Climate Button/Done Press and release this button to change the display on the Uconnect radio back to the Front Cli- mate Controls. Rear Passenger Temperature Up and Down Buttons Provides the rear passengers with independent temperature control. Push the up arrow button on the touchscreen to increase the temperature.
Page 97 GETTING TO KNOW YOUR VEHICLE 95 Icon Description Rear Passenger Climate Control OFF Button Press and release this button to turn the Rear Climate Controls off. Panel Mode Panel Mode Press this button on the touchscreen to change the air distribution mode to Panel Mode. In Panel Mode, air comes from the outlets in the instrument panel.
Page 98 96 GETTING TO KNOW YOUR VEHICLE Rear Automatic Temperature Control (ATC) — If 2. ATC is selected by adjusting the knob to the AUTO Equipped position. Once the desired temperature is displayed, the ATC System will automatically achieve and maintain that comfort level. When the system is set up for your comfort level, it is not necessary to change the settings.
Page 99 GETTING TO KNOW YOUR VEHICLE 97 Icon Description Bi-Level Mode Bi-Level Mode Air comes from both the headliner outlets and the floor outlets. NOTE: In many temperature positions, the Bi-Level mode is designed to provide cooler air out of the headliner outlets and warmer air from the floor outlets. Floor Mode Floor Mode Air comes from the floor outlets.
Page 100: Climate Control Functions
98 GETTING TO KNOW YOUR VEHICLE Icon Description Rear Climate Control/Blower Off To manually set the rear blower controls to off, press the Rear Climate Control/Blower Off button. Climate Control Functions • If fog or mist appears on the windshield or side glass, select Defrost Mode and adjust blower speed if needed.
Page 101 GETTING TO KNOW YOUR VEHICLE 99 NOTE: In cold weather, use of recirculation mode may lead 3. When the system is set up for your comfort level, it is to excessive window fogging. The recirculation feature not necessary to change the settings. You will experience may be unavailable (button on the touchscreen greyed out) the greatest efficiency by simply allowing the system to if conditions exist that could create fogging on the inside of...
Page 102: Operating Tips
100 GETTING TO KNOW YOUR VEHICLE Operating Tips blower setting on high. This will ensure adequate system lubrication to minimize the possibility of compressor dam- NOTE: Refer to the chart at the end of this section for age when the system is started again. suggested control settings for various weather conditions.
Page 103 GETTING TO KNOW YOUR VEHICLE 101 Operating Tips Chart...
Page 104: Windows
102 GETTING TO KNOW YOUR VEHICLE WINDOWS NOTE: For vehicles equipped with Uconnect, the power window switches will remain active for up to 10 minutes Power Windows after the ignition is cycled to the OFF position. Opening The window controls on the driver’s door trim panel either front door will cancel this feature.
Page 105 GETTING TO KNOW YOUR VEHICLE 103 Auto-Down Feature NOTE: • If the window runs into any obstacle during Auto- The driver’s power window switch has an Auto-Down Closure, it will reverse direction and then go back down. feature. Push the window switch past the first detent, Remove the obstacle and use the window switch again release, and the window will go down automatically.
Page 106: Wind Buffeting
104 GETTING TO KNOW YOUR VEHICLE Reset Auto-Up Should the Auto-Up feature stop working, the window may need to be reset. To reset Auto-Up: 1. Make sure the door is fully closed. 2. Pull the window switch up to close the window com- pletely and continue to hold the switch up for an additional two seconds after the window is closed.
Page 107: Power Sunroof - If Equipped
GETTING TO KNOW YOUR VEHICLE 105 POWER SUNROOF — IF EQUIPPED WARNING! (Continued) The power sunroof switch is located between the sun equipped with Keyless Enter-N-Go in the ACC or visors on the overhead console. ON/RUN mode. Occupants, particularly unattended children, can become entrapped by the power sun- roof while operating the power sunroof switch.
Page 108: Closing Sunroof
106 GETTING TO KNOW YOUR VEHICLE Wind Buffeting Manual Mode To open the sunroof, push and hold the switch rearward. Wind buffeting can be described as the perception of The sunroof will move rearward and automatically stop at pressure on the ears or a helicopter-type sound in the ears. full open position.
Page 109: Venting Sunroof - Express
GETTING TO KNOW YOUR VEHICLE 107 Venting Sunroof — Express HOOD Push and release the Vent button within one half second Opening and the sunroof will open to the vent position. This is Two latches must be released to open the hood. called “Express Vent”, and it will occur regardless of sunroof position.
Page 110 108 GETTING TO KNOW YOUR VEHICLE 2. Outside of the vehicle, locate the safety latch lever near 3. Use the hood prop rod to secure the hood in the open the center of the grille between the grille and hood position.
Page 111: Closing
GETTING TO KNOW YOUR VEHICLE 109 Closing LIFTGATE Opening WARNING! The liftgate can be unlocked or locked pushing the unlock Be sure the hood is fully latched before driving your or lock button on the Remote Keyless Entry key fob, the vehicle.
Page 112: Cargo Area Features
110 GETTING TO KNOW YOUR VEHICLE To open the unlocked liftgate, squeeze the handle and pull WARNING! the liftgate toward you. Gas props will raise and support the liftgate in the open position. • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle.
Page 113 GETTING TO KNOW YOUR VEHICLE 111 • 60/40 split second-row passenger seats with fold flat • An optional front passenger seat with fold flat feature, feature, which allows for extended cargo space. Refer to which extends cargo space even further. Refer to “Seats” “Seats”...
Page 114 112 GETTING TO KNOW YOUR VEHICLE To Install The Cover: 3. Insert the spring-loaded post on the opposite end of the cover housing into the attachment point on the opposite 1. Position the cover in the vehicle so that the flat side of side of the vehicle.
Page 115 GETTING TO KNOW YOUR VEHICLE 113 Cargo tie-downs are located on both rear trim panels. WARNING! These tie-downs should be used to secure loads safely when the vehicle is moving. In a collision, a loose cargo cover in the vehicle could cause injury.
Page 116: Garage Door Opener - If Equipped
114 GETTING TO KNOW YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED WARNING! HomeLink replaces up to three remote controls (hand-held The weight and position of cargo and passengers can transmitters) that operate devices such as garage door change the vehicle center of gravity and vehicle han- openers, motorized gates, lighting or home security sys- dling.
Page 117: Before You Begin Programming Homelink
GETTING TO KNOW YOUR VEHICLE 115 To erase the channels, place the ignition in the ON/RUN position, and push and hold the two outside HomeLink buttons (I and III) for up to 20 seconds or until the orange indicator flashes. NOTE: •...
Page 118 116 GETTING TO KNOW YOUR VEHICLE 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink button you wish to program while keeping the HomeLink indicator light in view. 3. Push and hold the HomeLink button you want to program while you push and hold the hand-held trans- mitter button.
Page 119 GETTING TO KNOW YOUR VEHICLE 117 6. Return to the vehicle and push the programmed 3. Push and hold the HomeLink button you want to HomeLink button twice (holding the button for two program while you push and hold the hand-held trans- seconds each time).
Page 120: Canadian/Gate Operator Programming
118 GETTING TO KNOW YOUR VEHICLE Canadian/Gate Operator Programming 3. Continue to push and hold the HomeLink button while you push and release (“cycle”) your hand-held trans- For programming transmitters in Canada/United States mitter every two seconds until HomeLink has success- that require the transmitter signals to “time-out”...
Page 121: Using Homelink
GETTING TO KNOW YOUR VEHICLE 119 Using HomeLink • Push the LEARN button on the Garage Door Opener to complete the training for a Rolling Code. To operate, push and release the programmed HomeLink button. Activation will now occur for the programmed •...
Page 122: General Information
120 GETTING TO KNOW YOUR VEHICLE INTERNAL EQUIPMENT WARNING! (Continued) Storage use a garage door opener without these safety fea- tures. Call toll-free 1-800-355-3515 or, on the Internet Glove Compartment at HomeLink.com for safety information or assis- The glove compartment is located on the passenger side of tance.
Page 123 GETTING TO KNOW YOUR VEHICLE 121 Floor Console Storage Center Console Storage An open storage area, or cubby bin, is located in the floor There is a storage tray and storage compartment located console. under the center console armrest. Floor Console Cubby Bin Center Console...
Page 124 122 GETTING TO KNOW YOUR VEHICLE Pull upward on the release handle, located on the front of the lid, to gain access to the storage tray and storage compartment. Center Console Storage Compartment WARNING! Center Console Storage Tray Do not operate this vehicle with a console compart- The storage tray can be slid forward and rearward or ment lid in the open position.
Page 125 GETTING TO KNOW YOUR VEHICLE 123 Sliding Armrest Second-Row Map Pocket And Grocery Retainers — If Equipped The center console armrest can also slide rearward for easy access to the storage area. A map storage pocket and grocery retainers are located on the back of the driver’s and passenger’s seatbacks.
Page 126 124 GETTING TO KNOW YOUR VEHICLE An in-floor storage bin is located behind each front seat. The liner can be removed for easy cleaning. Each 1.6 gal (5.9L) bin can hold up to 12, 12 oz (0.35L) cans, plus ice, or other items. The removable bin liner allows for easy filling, emptying, and cleaning.
Page 127: Cupholders
GETTING TO KNOW YOUR VEHICLE 125 Cupholders When the armrest is folded flat the cupholders are in the back of the Head Restraint. The Head Restraint can be There are two cupholders, located in the center floor adjusted to better position the cupholders. console, for the front passengers.
Page 128: Power Outlets
126 GETTING TO KNOW YOUR VEHICLE Power Outlets In addition to cupholders, vehicles may also be equipped with bottle holders. The bottle holders are located on the A 12 Volt (13 Amp) power outlet is located in the center door trim panels. console below the radio.
Page 129 GETTING TO KNOW YOUR VEHICLE 127 A second 12 Volt (13 Amp) power outlet is located inside A third fused 12 Volt power outlet is located on the back of the center console storage area. Power is available with the the center console.
Page 130 128 GETTING TO KNOW YOUR VEHICLE A fourth fused 12 Volt power outlet is located on the left CAUTION! quarter trim panel in the cargo area. This power outlet has power available when the ignition is in the ON or ACC •...
Page 131 GETTING TO KNOW YOUR VEHICLE 129 WARNING! (Continued) • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
Page 132: Power Inverter - If Equipped
130 GETTING TO KNOW YOUR VEHICLE CAUTION! (Continued) • Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Power Inverter — If Equipped Your vehicle may be equipped with a 115 or 230 Volt AC (150 Watt maximum) power outlet located on the back of the center console.
Page 133: Sunglasses Storage
GETTING TO KNOW YOUR VEHICLE 131 NOTE: Due to built-in overload protection, the power Vehicles Equipped With Uconnect 3/3 NAV outlet will shut down if the 115 Volt AC (150 Watt maxi- To turn the power inverter on or off perform the following: mum) power rating is exceeded.
Page 134: Roof Luggage Rack - If Equipped
132 GETTING TO KNOW YOUR VEHICLE ROOF LUGGAGE RACK — IF EQUIPPED The roof rack cross rails and side rails are designed to carry cargo weight. The load must not exceed 150 lbs (68 kg), and it should be distributed uniformly over the cross rails. In addition, the roof rack does not increase the total load carrying capacity of the vehicle.
Page 135 GETTING TO KNOW YOUR VEHICLE 133 4. Attempt to move the crossbar to ensure that it is locked CAUTION! in position. • To prevent damage to the roof of your vehicle, DO NOT NOTE: carry any loads on the roof rack without the crossbars •...
Page 137 GETTING TO KNOW YOUR INSTRUMENT PANEL CONTENTS INSTRUMENT CLUSTER ....136 ▫ Yellow Warning Lights ....150 ▫...
Page 138: Instrument Cluster
136 GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER Instrument Cluster Instrument Cluster Descriptions 2. Instrument Cluster Display • When the appropriate conditions exist, this display 1. Tachometer shows the instrument cluster display messages. Refer • Indicates the engine speed in revolutions per minute to “Instrument Cluster Display”...
Page 139 GETTING TO KNOW YOUR INSTRUMENT PANEL 137 3. Speedometer WARNING! (Continued) • Indicates vehicle speed. coolant. You may want to call an authorized dealer for 4. Fuel Gauge service if your vehicle overheats. If you decide to look under the hood yourself, see “Servicing And Mainte- •...
Page 140: Instrument Cluster Display
138 GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DISPLAY Your vehicle may be equipped with an instrument cluster display, which offers useful information to the driver. With the ignition in the STOP/OFF mode, opening/closing of a door will activate the display for viewing, and display the total miles, or kilometers, in the odometer.
Page 141: Oil Change Due
GETTING TO KNOW YOUR INSTRUMENT PANEL 139 • Messages • Down Arrow Button • Push and release the down arrow button to • Turn Menu OFF scroll downward through the main menus and The system allows the driver to select information by submenus.
Page 142: Display Menu Items
140 GETTING TO KNOW YOUR INSTRUMENT PANEL Display Menu Items Unless reset, this message will continue to display each time you cycle the ignition to the ON/RUN position. To Fuel Economy turn off the message temporarily, push and release the up Push and release the up or down arrow button until “Fuel arrow button.
Page 143 GETTING TO KNOW YOUR INSTRUMENT PANEL 141 When the DTE value is less than 30 miles (48 km) estimated driving distance, the DTE display will change to a “LOW FUEL” message. This display will continue until the ve- hicle runs out of fuel. Adding a significant amount of fuel to the vehicle will turn off the “LOW FUEL”...
Page 144 142 GETTING TO KNOW YOUR INSTRUMENT PANEL • Shows the elapsed time traveled for Trip A since the last Trip Info reset. Push and release the up or down arrow button until “Trip Info” displays highlighted in the instrument cluster display Trip B and push the right arrow button.
Page 145: Battery Saver On/Battery Saver Mode Message - Electrical Load Reduction Actions - If Equipped
GETTING TO KNOW YOUR INSTRUMENT PANEL 143 Vehicle Info (Customer Information Features) the right arrow button will display a stored warning message. Push and release the up or down arrow button if Push and release the up or down arrow button until there is more than one message to step through the “Vehicle Info”...
Page 146 144 GETTING TO KNOW YOUR INSTRUMENT PANEL • Rear Defroster And Heated Mirrors depletion to the point where the vehicle may stall due to lack of electrical supply, or will not restart after the current • HVAC System drive cycle. •...
Page 147: Warning Lights And Messages
GETTING TO KNOW YOUR INSTRUMENT PANEL 145 • The vehicle was parked for an extended period of time After a trip: (weeks, months). • Check if any aftermarket equipment was installed (ad- ditional lights, upfitter electrical accessories, audio sys- • The battery was recently replaced and was not charged tems, alarms) and review specifications if any (load and completely.
Page 148: Red Warning Lights
146 GETTING TO KNOW YOUR INSTRUMENT PANEL Red Warning Lights — Brake Warning Light This light monitors various brake functions, including — Seat Belt Reminder Warning Light brake fluid level and parking brake application. If the This light indicates when the driver or passenger seat belt brake light turns on it may indicate that the parking brake is unbuckled.
Page 149 GETTING TO KNOW YOUR INSTRUMENT PANEL 147 NOTE: The light may flash momentarily during sharp The light also will turn on when the parking brake is cornering maneuvers, which change fluid level conditions. applied with the ignition switch in the ON/RUN position. The vehicle should have service performed, and the brake NOTE: This light shows only that the parking brake is fluid level checked.
Page 150 148 GETTING TO KNOW YOUR INSTRUMENT PANEL — Transmission Temperature Warning Light — If — Battery Charge Warning Light Equipped This light illuminates when the battery is not charging This light indicates high transmission fluid temperature. properly. If it stays on while the engine is running, there This may occur with strenuous usage such as trailer may be a malfunction with the charging system.
Page 151 GETTING TO KNOW YOUR INSTRUMENT PANEL 149 — Electronic Throttle Control (ETC) Warning — Electric Power Steering Fault Warning Light Light This light will turn on when there’s a fault with the EPS This light informs you of a problem with the Electronic (Electric Power Steering) system.
Page 152: Yellow Warning Lights
150 GETTING TO KNOW YOUR INSTRUMENT PANEL Yellow Warning Lights WARNING! — Engine Check/Malfunction Indicator Warning A malfunctioning catalytic converter, as referenced Light (MIL) above, can reach higher temperatures than in normal The Engine Check/Malfunction Indicator Light (MIL) is a operating conditions.
Page 153 GETTING TO KNOW YOUR INSTRUMENT PANEL 151 — Electronic Stability Control (ESC) Active — Electronic Stability Control (ESC) Off Warning Warning Light — If Equipped Light — If Equipped This light will indicate when the Electronic Stability Con- This light indicates the Electronic Stability Control (ESC) is trol system is Active.
Page 154 152 GETTING TO KNOW YOUR INSTRUMENT PANEL can lead to tire failure. Under-inflation also reduces fuel CAUTION! efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Do not continue driving with one or more flat tires as handling may be compromised.
Page 155: Green Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 153 ensure that the replacement or alternate tires and wheels If the ABS light remains on or turns on while driving, then allow the TPMS to continue to function properly. the Anti-Lock portion of the brake system is not function- ing and service is required as soon as possible.
Page 156: White Indicator Lights
154 GETTING TO KNOW YOUR INSTRUMENT PANEL White Indicator Lights — Front Fog Indicator Light — If Equipped This indicator will illuminate when the front fog lights are — Cruise Control Ready Indicator This light will turn on when the speed control is ready, but —...
Page 157: Onboard Diagnostic System (Obd Ii) Cybersecurity
GETTING TO KNOW YOUR INSTRUMENT PANEL 155 If any of these systems require service, the OBD II system WARNING! will turn on the Malfunction Indicator Light (MIL). It will also store diagnostic codes and other information to assist • ONLY an authorized service technician should con- your service technician in making repairs.
Page 158: Emissions Inspection And Maintenance Programs
156 GETTING TO KNOW YOUR INSTRUMENT PANEL EMISSIONS INSPECTION AND MAINTENANCE NOTE: If you crank or start the engine, you will have to PROGRAMS start this test over. In some localities, it may be a legal requirement to pass an 2.
Page 159 GETTING TO KNOW YOUR INSTRUMENT PANEL 157 If your OBD II system is not ready, you should see your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.
Page 161 SAFETY CONTENTS SAFETY FEATURES ..... .160 ▫ Child Restraints ..... . .203 ▫...
Page 162: Safety Features
160 SAFETY SAFETY FEATURES These are all normal characteristics of ABS. Anti-Lock Brake System (ABS) WARNING! The Anti-Lock Brake System (ABS) provides increased • The ABS contains sophisticated electronic equip- vehicle stability and brake performance under most brak- ment that may be susceptible to interference caused ing conditions.
Page 163: Electronic Brake Control System
SAFETY If the “Anti-Lock Brake Warning Light” is on, the brake WARNING! (Continued) system should be serviced as soon as possible to restore the • The capabilities of an ABS equipped vehicle must benefits of anti-lock brakes. If the “Anti-Lock Brake Warn- never be exploited in a reckless or dangerous manner ing Light”...
Page 164 162 SAFETY Brake Assist System (BAS) WARNING! (Continued) The BAS is designed to optimize the vehicle’s braking exploited in a reckless or dangerous manner, which capability during emergency braking maneuvers. The sys- could jeopardize the user’s safety or the safety of tem detects an emergency braking situation by sensing the others.
Page 165 SAFETY Electronic Roll Mitigation (ERM) Electronic Stability Control (ESC) This system anticipates the potential for wheel lift by This system enhances directional control and stability of monitoring the driver’s steering wheel input and the speed the vehicle under various driving conditions. ESC corrects of the vehicle.
Page 166 164 SAFETY The “ESC Activation/Malfunction Indicator Light” located WARNING! (Continued) in the instrument cluster will start to flash as soon as the driver input for the conditions. Only a safe, attentive, ESC system becomes active. The “ESC Activation/ and skillful driver can prevent accidents. The capa- Malfunction Indicator Light”...
Page 167 SAFETY ESC Operating Modes WARNING! NOTE: Depending upon model and mode of operation, the • When in “Partial Off” mode, the TCS functionality ESC system may have multiple operating modes. of ESC, (except for the limited slip feature described ESC On in the TCS section), has been disabled and the “ESC Off Indicator Light”...
Page 168 166 SAFETY ESC Activation/Malfunction Indicator Light And NOTE: ESC OFF Indicator Light • The “ESC Activation/Malfunction Indicator Light” and the “ESC OFF Indicator Light” come on momentarily each time the ignition is turned ON. The “ESC Activation/Malfunction Indicator Light” in the instrument cluster will come on •...
Page 169 SAFETY The following conditions must be met in order for HSA to WARNING! activate: There may be situations where the Hill Start Assist • The feature must be enabled. (HSA) will not activate and slight rolling may occur, • The vehicle must be stopped. such as on minor hills or with a loaded vehicle, or while pulling a trailer.
Page 170 168 SAFETY • If disabling HSA using Uconnect Settings, refer to WARNING! “Uconnect Settings” in “Multimedia” for further infor- mation. • If you use a trailer brake controller with your trailer, the trailer brakes may be activated and deactivated For vehicles not equipped with an instrument cluster with the brake switch.
Page 171 SAFETY 8. Turn the ignition to the OFF mode and then back to ON. Trailer Sway Control (TSC) If the sequence was completed properly, the “ESC Off TSC uses sensors in the vehicle to recognize an excessively Indicator Light” will blink several times to confirm HSA swaying trailer and will take the appropriate actions to is disabled.
Page 172: Auxiliary Driving Systems
170 SAFETY AUXILIARY DRIVING SYSTEMS Tire Pressure Monitoring System (TPMS) The Tire Pressure Monitor System (TPMS) will warn the driver of a low tire pressure based on the vehicle recom- mended cold placard pressure. The tire pressure will vary with temperature by about 1 psi (7 kPa) for every 12°F (6.5°C).
Page 173 SAFETY The system will automatically update and the “Tire Pres- CAUTION! (Continued) sure Monitoring Telltale Light” will turn off once the warnings have been established for the tire size system receives the updated tire pressures. The vehicle equipped on your vehicle. Undesirable system op- may need to be driven for up to 20 minutes above 15 mph eration or sensor damage may result when using (24 km/h) in order for the TPMS to receive this informa-...
Page 174 172 SAFETY NOTE: Premium System • The TPMS is not intended to replace normal tire care and The Tire Pressure Monitor System (TPMS) uses wireless maintenance, or to provide warning of a tire failure or technology with wheel rim mounted electronic sensors to condition.
Page 175 SAFETY Tire Pressure Monitoring Low Pressure Warnings Should this occur, you should stop as soon as possible and inflate the tires with low pressure (those in a different color in the instrument cluster display graphic) to the vehicle’s The “Tire Pressure Monitoring Telltale Light” will recommended cold placard pressure value as shown in the illuminate in the instrument cluster and a chime Inflate to XX...
Page 176 174 SAFETY • Using tire chains on the vehicle. Service TPMS Warning When a system fault is detected, the “Tire Pressure Moni- • Using wheels/tires not equipped with TPMS sensors. toring Telltale Light” will flash on and off for 75 seconds NOTE: and then remain on solid.
Page 177 SAFETY • For each subsequent ignition switch cycle, a chime will To deactivate the TPMS, first replace all four wheel and tire sound, the “Tire Pressure Monitoring Telltale Light” will assemblies (road tires) with tires not equipped with Tire flash on and off for 75 seconds and then remain on solid, Pressure Monitoring (TPM) Sensors.
Page 178: Occupant Restraint Systems
176 SAFETY General Information Some of the safety features described in this section may be standard equipment on some models, or may be optional The following regulatory statement applies to all radio equipment on others. If you are not sure, ask your autho- frequency (RF) devices equipped in this vehicle: rized dealer.
Page 179: Seat Belt Systems
SAFETY restraints or belt-positioning booster seats should ride WARNING! properly buckled up in a vehicle with a rear seat. • Never place a rear-facing child restraint in front of an 4. Never allow children to slide the shoulder belt behind air bag.
Page 180 178 SAFETY Enhanced Seat Belt Use Reminder System (BeltAlert) BeltAlert Warning Sequence Driver and Passenger BeltAlert (if equipped) The BeltAlert warning sequence is activated when the vehicle is moving above a specified vehicle speed range BeltAlert is a feature intended to remind the driver and the driver or outboard front seat passenger is unbuck- and outboard front seat passenger (if equipped with led (if equipped with outboard front passenger seat...
Page 181 SAFETY Change of Status Lap/Shoulder Belts All seating positions in your vehicle are equipped with If the driver or outboard front seat passenger (if equipped lap/shoulder belts. with outboard front passenger seat BeltAlert) unbuckles their seat belt while the vehicle is traveling, the BeltAlert The seat belt webbing retractor will lock only during very warning sequence will begin until the seat belts are buck- sudden stops or collisions.
Page 182 180 SAFETY WARNING! (Continued) WARNING! • It is dangerous to ride in a cargo area, inside or • A lap belt worn too high can increase the risk of outside of a vehicle. In a collision, people riding in injury in a collision. The seat belt forces won’t be at these areas are more likely to be seriously injured or the strong hip and pelvic bones, but across your killed.
Page 183 SAFETY 2. The seat belt latch plate is above the back of the front WARNING! (Continued) seat, and next to your arm in the rear seat (for vehicles vehicle in a collision, increasing head and neck equipped with a rear seat). Grasp the latch plate and injury.
Page 184 182 SAFETY 3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Positioning The Lap Belt 5. Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfortable and Inserting Latch Plate Into Buckle not resting on your neck.
Page 185 SAFETY Lap/Shoulder Belt Untwisting Procedure Adjustable Upper Shoulder Belt Anchorage Use the following procedure to untwist a twisted lap/ In the driver and front passenger seats, the top of the shoulder belt. shoulder belt can be adjusted upward or downward to position the seat belt away from your neck.
Page 186 184 SAFETY As a guide, if you are shorter than average, you will prefer WARNING! (Continued) the shoulder belt anchorage in a lower position, and if you seat belt. Follow these instructions to wear your seat are taller than average, you will prefer the shoulder belt belt safely and to keep your passengers safe, too.
Page 187 SAFETY Seat Belts And Pregnant Women WARNING! • ONLY use a Seat Belt Extender if it is physically required in order to properly fit the original seat belt system. DO NOT USE the Seat Belt Extender if, when worn, the distance between the front edge of the Seat Belt Extender buckle and the center of the occupant’s body is LESS than 6 inches.
Page 188 186 SAFETY Seat Belt Pretensioner Switchable Automatic Locking Retractors (ALR) The front seat belt system is equipped with pretensioning The seat belts in the passenger seating positions are devices that are designed to remove slack from the seat belt equipped with a Switchable Automatic Locking Retractor in the event of a collision.
Page 189 SAFETY If the passenger seating position is equipped with an ALR WARNING! and is being used for normal usage, only pull the seat belt webbing out far enough to comfortably wrap around the • Never place a rear-facing child restraint in front of an occupant’s mid-section so as to not activate the ALR.
Page 190 188 SAFETY How To Disengage The Automatic Locking Mode Supplemental Active Head Restraints (AHR) These head restraints are passive, deployable components, Unbuckle the combination lap/shoulder belt and allow it and vehicles with this equipment cannot be readily iden- to retract completely to disengage the Automatic Locking tified by any markings, only through visual inspection of Mode and activate the vehicle sensitive (emergency) lock- the head restraint.
Page 191 SAFETY NOTE: The Active Head Restraints (AHR) may or may not WARNING! deploy in the event of a front or side impact. However, if during a front impact, a secondary rear impact occurs, the • All occupants, including the driver, should not oper- AHR may deploy based on the severity and type of the ate a vehicle or sit in a vehicle’s seat until the head impact.
Page 192: Supplemental Restraint Systems (Srs)
190 SAFETY Resetting Active Head Restraints (AHR) may result in damage to the AHRs that could impair their function. WARNING! Deployed AHRs are not able to best protect you in all types of collisions. Have deployed AHRs reset by an authorized dealer immediately.
Page 193 SAFETY • Steering Wheel and Column The ORC contains a backup power supply system that may deploy the air bag system even if the battery loses power or • Instrument Panel it becomes disconnected prior to deployment. • Knee Impact Bolsters The ORC turns on the Air Bag Warning Light in the •...
Page 194 192 SAFETY • The Air Bag Warning Light does not come on during the Front Air Bags four to eight seconds when the ignition switch is first in This vehicle has front air bags and lap/shoulder belts for both the ON/RUN position. the driver and front passenger.
Page 195 SAFETY The first stage inflator is triggered immediately during an WARNING! impact that requires air bag deployment. A low energy output is used in less severe collisions. A higher energy • Being too close to the steering wheel or instrument output is used for more severe collisions.
Page 196 194 SAFETY Because air bag sensors measure vehicle deceleration over WARNING! (Continued) time, vehicle speed and damage by themselves are not the air bags and you could be injured because the air good indicators of whether or not an air bag should have bags may no longer be functional.
Page 197 SAFETY The SABs may help to reduce the risk of occupant injury WARNING! during certain side impacts, in addition to the injury reduction potential provided by the seat belts and body • Do not drill, cut, or tamper with the knee impact structure.
Page 198 196 SAFETY When the SAB deploys, it opens the seam on the outboard side of the seatback’s trim cover. The inflating SAB deploys through the seat seam into the space between the occupant and the door. The SAB moves at a very high speed and with such a high force that it could injure occupants if they are not seated properly, or if items are positioned in the area where the SAB inflates.
Page 199 SAFETY positioned in the area where the SABICs inflate. Children Side Impacts are at an even greater risk of injury from a deploying air The Side Air Bags are designed to activate in certain side bag. impacts. The Occupant Restraint Controller (ORC) deter- The SABICs may help reduce the risk of partial or complete mines whether the deployment of the Side Air Bags in a ejection of vehicle occupants through side windows in...
Page 200 198 SAFETY Side Air Bags are a supplement to the seat belt restraint WARNING! system. Side Air Bags deploy in less time than it takes to blink your eyes. • Side Air Bags need room to inflate. Do not lean against the door or window.
Page 201 SAFETY The Side Air Bags will not deploy in all rollover events. The • Supplemental Side Air Bags rollover sensing system determines if a rollover event may • Supplemental Knee Air Bags be in progress and whether deployment is appropriate. In •...
Page 202 200 SAFETY • As the air bags deflate, you may see some smoke-like NOTE: particles. The particles are a normal by-product of the • Air bag covers may not be obvious in the interior trim, process that generates the non-toxic gas used for air bag but they will open during air bag deployment.
Page 203 SAFETY Enhanced Accident Response System Reset WARNING! (Continued) Procedure of the instrument panel. Do not modify the front In order to reset the Enhanced Accident Response System bumper, vehicle body structure, or add aftermarket functions after an event, the ignition switch must be side steps or running boards.
Page 204 202 SAFETY Event Data Recorder (EDR) These data can help provide a better understanding of the circumstances in which crashes and injuries occur. This vehicle is equipped with an event data recorder (EDR). The main purpose of an EDR is to record, in certain NOTE: EDR data are recorded by your vehicle only if a crash or near crash-like situations, such as an air bag non-trivial crash situation occurs;...
Page 205: Child Restraints
SAFETY Child Restraints There are different sizes and types of restraints for children from newborn size to the child almost large enough for an Everyone in your vehicle needs to be buckled up at all adult safety belt. Always check the child seat Owner’s times, including babies and children.
Page 206 204 SAFETY Summary Of Recommendations For Restraining Children In Vehicles Recommended Type Of Child Child Size, Height, Weight Or Age Restraint Infants and Toddlers Children who are two years old or Either an Infant Carrier or a Convert- younger and who have not reached ible Child Restraint, facing rearward the height or weight limits of their in the rear seat of the vehicle...
Page 207 SAFETY Infant And Child Restraints WARNING! Safety experts recommend that children ride rear-facing in • Never place a rear-facing child restraint in front of an the vehicle until they are two years old or until they reach air bag. A deploying passenger front air bag can either the height or weight limit of their rear-facing child cause death or serious injury to a child 12 years or restraint.
Page 208 206 SAFETY Older Children And Child Restraints WARNING! Children who are two years old or who have outgrown Do not install a rear-facing car seat using a rear support their rear-facing convertible child seat can ride forward- leg in this vehicle. The floor of this vehicle is not facing in the vehicle.
Page 209 SAFETY WARNING! WARNING! • Improper installation can lead to failure of an infant DEATH or SERIOUS INJURY can occur, • Follow all instructions on the child restraint and in or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the vehicle’s owner’s manual.
Page 210 208 SAFETY 2. Pull the release loop forward to release the latch and seat cushion. Booster Seat 4. Place the child upright in the seat with their back firmly against the seatback. Release Loop 3. Lift the seat cushion up and push back to lock it in the 5.
Page 211 SAFETY 7. Once the seat belt is long enough to fit properly, insert WARNING! the latch plate into the buckle until you hear a “click.” Securely lock the seat cushion into position before using the seat. Otherwise, the seat will not provide the proper stability for child seats and/or passengers.
Page 212 210 SAFETY Children Too Large For Booster Seats If the answer to any of these questions was “no,” then the child still needs to use a booster seat in this vehicle. If the Children who are large enough to wear the shoulder belt child is using the lap/shoulder belt, check seat belt fit comfortably, and whose legs are long enough to bend over periodically and make sure the seat belt buckle is latched.
Page 213 SAFETY Recommendations For Attaching Child Restraints Restraint Type Combined Use Any Attachment Method Shown With An “X” Below Weight of the LATCH – Lower Seat Belt Only LATCH – Lower Seat Belt + Top Child + Child Anchors Only Anchors + Top Tether Anchor Restraint Tether Anchor...
Page 214 212 SAFETY Lower Anchors And Tethers For CHildren (LATCH) used with the top tether anchorage to install the child Restraint System restraint. Please see the following table for more information. LATCH Positions For Installing Child Restraints In This Vehicle LATCH Label Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.
Page 215 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH What is the weight limit (child’s 65 lbs (29.5 kg) Use the LATCH anchorage system until the combined weight of the weight + weight of the child re- child and the child restraint is 65 lbs straint) for using the LATCH anchor- (29.5 kg).
Page 216 214 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH Can the rear-facing child restraint The child seat may touch the back of touch the back of the front passenger the front passenger seat if the child seat? restraint manufacturer also allows contact.
Page 217 SAFETY Locating The Upper Tether Anchorages Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage. Forward-facing child restraints and some rear- There are tether strap anchorages behind each facing child restraints will also be equipped with a tether second row seating position, located on the back strap.
Page 218 216 SAFETY You can install up to two child seats using the LATCH D and E. Do not use the center seat anchorage, C. If the system at the same time. If you are installing three child child seats do not block the center seat belt webbing and restraints, you must use the seat belt to install the center buckle, the center seat belt can be used to restrain an child restraint.
Page 219 SAFETY 1. Loosen the adjusters on the lower straps and on the WARNING! (Continued) tether strap of the child seat so that you can more easily • Never use the same lower anchorage to attach more attach the hooks or connectors to the vehicle anchor- than one child restraint.
Page 220 218 SAFETY 6. Test that the child restraint is installed tightly by pulling WARNING! back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any • Improper installation of a child restraint to the direction.
Page 221 SAFETY Please see the table below and the following sections for WARNING! more information. • Improper installation or failure to properly secure a Lap/Shoulder Belt Systems For Installing Child child restraint can lead to failure of the restraint. The Restraints In This Vehicle child could be badly injured or killed.
Page 222 220 SAFETY Frequently Asked Questions About Installing Child Restraints With Seat Belts What is the weight limit (child’s Weight limit of the Child Restraint Always use the tether anchor when weight + weight of the child re- using the seat belt to install a for- straint) for using the Tether Anchor ward facing child restraint, up to the with the seat belt to attach a forward...
Page 223 SAFETY back into the retractor. As the webbing retracts, you will WARNING! (Continued) hear a clicking sound. This means the seat belt is now in • Follow the child restraint manufacturer’s directions the Automatic Locking mode. exactly when installing an infant or child restraint. 6.
Page 224 222 SAFETY Installing A Child Restraint With A Cinching Latch 2. Next, pull enough of the seat belt webbing from the Plate (CINCH) — If Equipped: retractor to pass it through the belt path of the child restraint. Do not twist the belt webbing in the belt path. Child restraint systems are designed to be secured in vehicle seats by lap belts or the lap belt portion of a 3.
Page 225 SAFETY If the buckle or the cinching latch plate is too close to the WARNING! (Continued) belt path opening of the child restraint, you may have behind the top of the vehicle seat. See the section trouble tightening the seat belt. If this happens, disconnect “Lower Anchors and Tethers for CHildren (LATCH) the latch plate from the buckle and twist the short buckle- Restraint System”...
Page 226 224 SAFETY 1. Look behind the seating position where you plan to two posts. If not possible, lower the head restraint and install the child restraint to find the tether anchorage. pass the tether strap around the outboard side of the You may need to move the seat forward to provide head restraint.
Page 227: Transporting Pets
SAFETY SAFETY TIPS WARNING! Transporting Passengers • An incorrectly anchored tether strap could lead to NEVER TRANSPORT PASSENGERS IN THE CARGO increased head motion and possible injury to the AREA. child. Use only the anchorage position directly be- hind the child seat to secure a child restraint top WARNING! tether strap.
Page 228: Exhaust Gas
226 SAFETY Exhaust Gas Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the WARNING! vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the complete Exhaust gases can injure or kill.
Page 229: Windshield
SAFETY Air Bag Warning Light Floor Mat Safety Information The Air Bag warning light will turn on for four to Always use floor mats designed to fit your vehicle. Only eight seconds as a bulb check when the ignition switch use a floor mat that does not interfere with the operation of is first turned to ON/RUN.
Page 230 228 SAFETY WARNING! (Continued) WARNING! (Continued) • ALWAYS REMOVE THE EXISTING FLOOR MAT • ALWAYS make sure objects cannot fall or slide into the driver’s side floor area when the vehicle is FROM THE VEHICLE before installing any other moving. Objects can become trapped under accelera- floor mat.
Page 231: Periodic Safety Checks You Should Make Outside
SAFETY Periodic Safety Checks You Should Make Outside The Vehicle Tires Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks.
Page 233 STARTING AND OPERATING CONTENTS STARTING THE ENGINE ....233 ▫ Four-Speed Or Six-Speed Automatic Transmission ......241 ▫...
Page 234 232 STARTING AND OPERATING ▫ ParkSense Sensors ..... .253 ▫ Loading ......264 ▫...
Page 235: Starting The Engine
STARTING AND OPERATING 233 STARTING THE ENGINE WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust the • Do not leave children or animals inside parked inside and outside mirrors, fasten your seat belt, and if vehicles in hot weather. Interior heat build-up may present, instruct all other occupants to buckle their seat cause serious injury or death.
Page 236: Normal Starting
234 STARTING AND OPERATING Normal Starting 3. If the gear selector is not in PARK, the ENGINE START/ STOP button must be held for two seconds or three short To Turn On The Engine Using The ENGINE START/ pushes in a row with the vehicle speed above 5 mph STOP Button (8 km/h) before the engine will shut off.
Page 237: Keyless Enter-N-Go - Ignition
STARTING AND OPERATING 235 Keyless Enter-N-Go — Ignition ENGINE START/STOP Button Functions — With Driv- er’s Foot OFF The Brake Pedal (In PARK Or NEUTRAL Position) The ENGINE START/STOP button operates similar to an ignition switch. It has three modes: OFF, ACC, and RUN. To change the ignition modes without starting the vehicle and use the accessories, follow these directions: 1.
Page 238: Cold Weather Operation
236 STARTING AND OPERATING Cold Weather Operation (Below –22°F Or −30°C) After Starting To ensure reliable starting at these temperatures, use of an The idle speed is controlled automatically, and it will externally powered electric engine block heater (available decrease as the engine warms up. from your authorized dealer) is recommended.
Page 239: Engine Break-In Recommendations
STARTING AND OPERATING 237 ENGINE BREAK-IN RECOMMENDATIONS CAUTION! A long break-in period is not required for the engine and Never use Non-Detergent Oil or Straight Mineral Oil drivetrain (transmission and axle) in your vehicle. in the engine or damage may result. Drive moderately during the first 300 miles (500 km).
Page 240 238 STARTING AND OPERATING The foot operated parking brake is located below the lower NOTE: left corner of the instrument panel. To apply the park • When the parking brake is applied and the transmission brake, firmly push the park brake pedal fully. To release the is placed in gear, the “Brake Warning Light”...
Page 241: Automatic Transmission
STARTING AND OPERATING 239 WARNING! WARNING! (Continued) PARK. Failure to do so may cause the vehicle to roll • Never use the PARK position as a substitute for the and cause damage or injury. parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and CAUTION! possible injury or damage.
Page 242: Ignition Park Interlock
240 STARTING AND OPERATING WARNING! (Continued) CAUTION! • Unintended movement of a vehicle could injure those Damage to the transmission may occur if the following in or near the vehicle. As with all vehicles, you should precautions are not observed: never exit a vehicle while the engine is running.
Page 243: Brake/Transmission Shift Interlock System
STARTING AND OPERATING 241 NOTE: The transmission is NOT locked in PARK when the You must press the brake pedal to move the gear selector ignition is in the ACC mode (even though the engine will out of PARK (refer to “Brake/Transmission Shift Interlock be off).
Page 244: Gear Ranges
242 STARTING AND OPERATING Gear Ranges The transmission gear selector provides PARK, REVERSE, NEUTRAL, DRIVE, and AutoStick (-/+) shift positions. Do not depress the accelerator pedal when shifting from Manual shifts can be made using the AutoStick shift PARK or NEUTRAL into another gear range. control.
Page 245 STARTING AND OPERATING 243 When exiting the vehicle, always: WARNING! (Continued) • Apply the parking brake. engine is idling normally and your foot is firmly • Shift the transmission into PARK. pressing the brake pedal. • Unintended movement of a vehicle could injure •...
Page 246 244 STARTING AND OPERATING • Look at the transmission gear position display and WARNING! (Continued) verify that it indicates the PARK position (P). • Do not leave the key fob in or near the vehicle (or in • With brake pedal released, verify that the gear selector a location accessible to children), and do not leave will not move out of PARK.
Page 247 STARTING AND OPERATING 245 to select a lower gear. Under these conditions, using a CAUTION! lower gear will improve performance and extend transmis- sion life by reducing excessive shifting and heat buildup. Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause If the transmission temperature exceeds normal operating severe transmission damage.
Page 248 246 STARTING AND OPERATING • The transmission will automatically upshift when nec- Autostick essary to prevent engine over-speed. AutoStick is a driver-interactive transmission feature pro- • The transmission will automatically downshift as the viding manual shift control, giving you more control of the vehicle.
Page 249 STARTING AND OPERATING 247 To disengage AutoStick mode, return the gear selector to In the event of a momentary problem, the transmission can the DRIVE position. You can shift in or out of the AutoStick be reset to regain all forward gears by performing the position at any time without taking your foot off the following steps: accelerator pedal.
Page 250: Power Steering
248 STARTING AND OPERATING Overdrive Operation NOTE: The torque converter clutch will not engage until the transmission fluid and engine coolant are warm (usu- The automatic transmission includes an electronically con- ally after 1 to 3 miles [2 to 5 km] of driving). Because the trolled Overdrive (top gear).
Page 251: Power Steering Fluid Check
STARTING AND OPERATING 249 NOTE: WARNING! • Increased noise levels at the end of the steering wheel Fluid level should be checked on a level surface and travel are considered normal and do not indicate that with the engine off to prevent injury from moving there is a problem with the power steering system.
Page 252: All Wheel Drive (Awd) - If Equipped
250 STARTING AND OPERATING ALL WHEEL DRIVE (AWD) — IF EQUIPPED The Speed Control buttons are located on the right side of the steering wheel. This feature provides on-demand All-Wheel Drive (AWD). The system is automatic with no driver inputs or addi- tional driving skills required.
Page 253: To Activate
STARTING AND OPERATING 251 To Activate To Vary The Speed Setting Push the ON/OFF button. The Cruise Indicator Light in To Increase Speed the instrument cluster display will illuminate. To turn the When the Speed Control is set, you can increase speed by system off, push the ON/OFF button a second time.
Page 254: To Accelerate For Passing
252 STARTING AND OPERATING To Accelerate For Passing To Decrease Speed When the Speed Control is set, you can decrease speed by Press the accelerator as you would normally. When the pushing the SET (-) button. pedal is released, the vehicle will return to the set speed. The driver’s preferred units can be selected through the Using Speed Control On Hills instrument panel settings if equipped.
Page 255: To Resume Speed
STARTING AND OPERATING 253 To Resume Speed ParkSense will retain the last system state (enabled or disabled) from the last ignition cycle when the ignition is To resume a previously set speed, push the RES (+) button changed to the ON/RUN position. and release.
Page 256: Parksense Warning Display
254 STARTING AND OPERATING ParkSense Warning Display The ParkSense Warning screen will only be displayed if “Sound and Display” is selected from the Uconnect Sys- tem. Refer to “Uconnect Settings” in “Multimedia” for further information. The ParkSense Warning screen is located within the instru- ment cluster display.
Page 257 STARTING AND OPERATING 255 The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the obstacle, the instrument cluster display will show fewer arcs and the sound tone will change from slow, to fast, to continuous.
Page 258 256 STARTING AND OPERATING Fast Tone Continuous Tone The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle:...
Page 259: Enabling And Disabling Parksense
STARTING AND OPERATING 257 WARNING ALERTS Rear Distance Greater than 79-39 inches 39-25 inches 25-12 inches Less than (inches/cm) 79 inches (200 (200-100 cm) (100-65 cm) (65-30 cm) 12 inches (30 cm) Audible Alert None Single 1/2- Slow Fast Continuous Chime Second Tone Arcs...
Page 260: Cleaning The Parksense System
258 STARTING AND OPERATING • When you turn ParkSense off, the instrument cluster If “CLEAN PARK ASSIST” appears in the instrument display will read “PARK ASSIST SYSTEM OFF.” Further- cluster display, make sure the outer surface and the under- more, once you turn ParkSense off, it remains off until you side of the rear fascia/bumper are clean and clear of snow, turn it on again, even if you cycle the ignition key.
Page 261: Parkview Rear Back Up Camera - If Equipped
STARTING AND OPERATING 259 WARNING! CAUTION! • Drivers must be careful when backing up even when • ParkSense is only a parking aid and it is unable to using ParkSense. Always check carefully behind recognize every obstacle, including small obstacles. your vehicle, look behind you, and be sure to check Parking curbs might be temporarily detected or not for pedestrians, animals, other vehicles, obstructions,...
Page 262 260 STARTING AND OPERATING When the vehicle is shifted out of REVERSE, the rear vehicle to assist with parking or aligning to a hitch/ camera mode is exited and the last selected touchscreen receiver. The static grid lines will show separate zones that appears again.
Page 263: Refueling The Vehicle
STARTING AND OPERATING 261 REFUELING THE VEHICLE WARNING! The gas cap is located behind the fuel filler door on the left Drivers must be careful when backing up even when side of the vehicle. If the gas cap is lost or damaged, be sure using the ParkView Rear Back Up Camera.
Page 264: Loose Fuel Filler Cap Message
262 STARTING AND OPERATING WARNING! CAUTION! (Continued) • To avoid fuel spillage and overfilling, do not “top • Never have any smoking materials lit in or near the off” the fuel tank after filling. When the fuel nozzle vehicle when the gas cap is removed or the tank is “clicks”...
Page 265: Vehicle Loading
STARTING AND OPERATING 263 VEHICLE LOADING The bar code allows a computer scanner to read the VIN. The load carrying capacity of your vehicle is shown on the Gross Vehicle Weight Rating (GVWR) “Vehicle Certification Label”. This information should be The GVWR is the total allowable weight of your vehicle.
Page 266: Overloading
264 STARTING AND OPERATING Overloading Improper weight distribution can have an adverse effect on the way your vehicle steers and handles and the way the The load carrying components (axle, springs, tires, wheels, brakes operate. etc.) of your vehicle will provide satisfactory service as long as you do not exceed the GVWR and the front and TRAILER TOWING rear GAWR.
Page 267 STARTING AND OPERATING 265 Gross Trailer Weight (GTW) WARNING! The GTW is the weight of the trailer plus the weight of all It is important that you do not exceed the maximum cargo, consumables, and equipment (permanent or tempo- front or rear GAWR. A dangerous driving condition rary) loaded in or on the trailer in its loaded and ready for can result if either rating is exceeded.
Page 268: Trailer Hitch Classification
266 STARTING AND OPERATING Trailer Sway Control — Mechanical sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability. Trailer sway The trailer sway control is a telescoping link that can be control and a weight distributing (load equalizing) hitch installed between the hitch receiver and the trailer tongue are recommended for heavier Tongue Weights (TW) and that typically provides adjustable friction associated with...
Page 269: Trailer Towing Weights (Maximum Trailer Weight Ratings)
STARTING AND OPERATING 267 Trailer Hitch Classification Definitions Class Max. Trailer Hitch Industry Standards Class I - Light Duty 2,000 lbs (907 kg) Class II - Medium Duty 3,500 lbs (1,587 kg) Class III - Heavy Duty 5,000 lbs (2,267 kg) Class IV - Extra Heavy Duty 10,000 lbs (4,535 kg) Refer to the “Trailer Towing Weights (Maximum Trailer Weight Ratings)”...
Page 270 268 STARTING AND OPERATING GCWR (Gross Com- Max. GTW (Gross Max. Tongue Engine/Transmission Frontal Area bined Wt. Rating) Trailer Wt.) 3.6L/Automatic 7,300 lbs (3,311 kg) 32 sq ft (3.0 sq 2,500 lbs (1,133 kg) 200 lbs (90 kg) which includes 1 to 2 persons &...
Page 271: Trailer And Tongue Weight
STARTING AND OPERATING 269 Trailer And Tongue Weight NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional Never exceed the maximum tongue weight stamped on factory-installed options or dealer-installed options must your bumper or trailer hitch.
Page 272 270 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • When hauling cargo or towing a trailer, do not 3. GAWR overload your vehicle or trailer. Overloading can 4. Tongue weight rating for the trailer hitch utilized. cause a loss of control, poor performance, or damage to brakes, axle, engine, transmission, steering, sus- Perform the maintenance listed in the “Maintenance Plan”.
Page 273 STARTING AND OPERATING 271 • Proper tire inflation pressures are essential to the safe • An electronically actuated trailer brake controller is and satisfactory operation of your vehicle. Refer to required when towing a trailer with electronically actu- “Tires” in “Servicing And Maintenance” for proper tire ated brakes.
Page 274 272 STARTING AND OPERATING NOTE: CAUTION! • Disconnect trailer wiring connector from the vehicle If the trailer weighs more than 1,000 lbs (453 kg) before launching a boat (or any other device plugged loaded, it should have its own brakes and they should into vehicle’s electrical connect) into water.
Page 275: Towing Tips
STARTING AND OPERATING 273 Automatic Transmission The DRIVE range can be selected when towing. However, if frequent shifting occurs while in DRIVE, use the AutoStick shift control to manually select a lower gear. NOTE: Using a lower gear while operating the vehicle under heavy loading conditions will improve performance and extend transmission life by reducing excessive shifting and heat build up.
Page 276 274 STARTING AND OPERATING Speed Control — If Equipped to avoid extended driving at high RPM. Return to a higher gear or vehicle speed when grade and road • Do not use on hilly terrain or with heavy loads. conditions allow. •...
Page 277: Recreational Towing (Behind Motorhome, Etc.)
STARTING AND OPERATING 275 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Wheel OFF the Ground FWD Models AWD Models Flat Tow NONE NOT ALLOWED NOT ALLOWED Dolly Tow Front NOT ALLOWED Rear NOT ALLOWED NOT ALLOWED On Trailer NOTE: When towing your vehicle, always follow applicable state and provincial laws.
Page 278: Driving Tips
276 STARTING AND OPERATING DRIVING TIPS CAUTION! Driving On Slippery Surfaces • DO NOT flat tow this vehicle. Damage to the drive- Acceleration train will result. If this vehicle requires towing, make sure the drive wheels are OFF the ground. Rapid acceleration on snow covered, wet, or other slippery •...
Page 279: Driving Through Water
STARTING AND OPERATING 277 Traction Flowing/Rising Water When driving on wet or slushy roads, it is possible for a WARNING! wedge of water to build up between the tire and road surface. This is hydroplaning and may cause partial or Do not drive on or across a road or path where water is complete loss of vehicle control and stopping ability.
Page 280 278 STARTING AND OPERATING WARNING! CAUTION! (Continued) • Do not exceed 5 mph (8 km/h) when driving through • Driving through standing water limits your vehicle’s standing water. This will minimize wave effects. traction capabilities. Do not exceed 5 mph (8 km/h) •...
Page 281 IN CASE OF EMERGENCY CONTENTS HAZARD WARNING FLASHERS ... .280 JUMP STARTING ......302 BULB REPLACEMENT .
Page 282: Hazard Warning Flashers
280 IN CASE OF EMERGENCY HAZARD WARNING FLASHERS This is an emergency warning system and it should not be used when the vehicle is in motion. Use it when your The Hazard Warning flasher switch is located on the switch vehicle is disabled and it is creating a safety hazard for bank just above the climate controls.
Page 283 IN CASE OF EMERGENCY 281 Exterior Bulbs Bulb Number Low Beam Headlamp 9006 High Beam Headlamp 9005 Front Park/Turn Signal 3757AK Side Marker Lamp Front Fog Lamp PSX24W or 2504 Center High Mounted Stop Lamp (CHMSL) LED (Serviced at authorized dealer) License Lamp Exterior Bulbs –...
Page 284: Replacing Exterior Bulbs
282 IN CASE OF EMERGENCY Replacing Exterior Bulbs NOTE: Lens fogging can occur under certain atmospheric conditions. This will usually clear as atmospheric condi- tions change to allow the condensation to change back into a vapor. Turning the lamps on will usually accelerate the clearing process.
Page 285 IN CASE OF EMERGENCY 283 3. Disconnect the bulb from the harness connector and 1. Remove the fasteners retaining the front lower wheel then connect the replacement bulb. well access panel and remove the access panel. 2. Remove the electrical connector from the fog lamp CAUTION! housing.
Page 286 284 IN CASE OF EMERGENCY License Plate Lamp CAUTION! 1. Push the small locking tab sticking out of the end of the Never introduce leaded fuel to the tank, even in small lens toward the side of the vehicle and hold it in that amounts in an emergency, as this would damage the position.
Page 287: Fuses
IN CASE OF EMERGENCY 285 FUSES 2. Insert a small flat-blade tool between the end of the lens with the locking tab and the surrounding housing and then pivot the tool to separate the lens from the housing. WARNING! 3. Hold the lens with one hand and rotate the bulb’s •...
Page 288: Interior Fuses
286 IN CASE OF EMERGENCY Interior Fuses The interior fuse panel is located on the passenger side under the instrument panel. Cavity Cartridge Fuse Mini-Fuse Description F100 30 Amp Pink – 110V AC Inverter – If Equipped F101 – 10 Amp Red Interior Lights F102 –...
Page 289 IN CASE OF EMERGENCY 287 Cavity Cartridge Fuse Mini-Fuse Description F117 – 10 Amp Red Heated Mirrors F118 – 10 Amp Red Occupant Restraint Controller F119 – 10 Amp Red Steering Column Control Module F120 – 10 Amp Red All Wheel Drive – If Equipped F121 –...
Page 290: Underhood Fuses (Power Distribution Center)
288 IN CASE OF EMERGENCY Underhood Fuses (Power Distribution Center) The power distribution center is located in the engine compartment. Power Distribution Center Cavity Cartridge Fuse Mini-Fuse Description F101 60 Amp Yellow – Interior Power Distribution Center Rail F102 60 Amp Yellow –...
Page 291 IN CASE OF EMERGENCY 289 Cavity Cartridge Fuse Mini-Fuse Description F106 60 Amp Yellow – Interior Power Distribution Center Rail Run/ Accessory Relays F139 40 Amp Green – Climate Control System Blower F140 30 Amp Pink – Power Locks F141 40 Amp Green –...
Page 292 290 IN CASE OF EMERGENCY Cavity Cartridge Fuse Mini-Fuse Description F159 – 10 Amp Red Spare F160 – 20 Amp Yellow Interior Lights F161 – 20 Amp Yellow Horn F162 40 Amp Red/20 – Cabin Heater #1/Vacuum Pump – If Amp Lt.
Page 293: Jacking And Tire Changing
IN CASE OF EMERGENCY 291 Cavity Cartridge Fuse Mini-Fuse Description F177 – 20 Amp Yellow All Wheel Drive Module – If Equipped F178 – 25 Amp Clear Sunroof – If Equipped F179 – 10 Amp Red Battery Sensor F181 100 Amp Blue –...
Page 294: Jack Location
292 IN CASE OF EMERGENCY Jack Location Spare Tire Removal The jack and jack-handle are stowed underneath a cover in NOTE: On seven-passenger models, fold the third-row the rear storage bin in the cargo area. passenger seats flat. This will provide more space when accessing the jacking tools and when operating the winch mechanism.
Page 295: Preparations For Jacking
IN CASE OF EMERGENCY 293 NOTE: Assemble components 2 and 3 by seating the small ball at the end of component 2 in the small hole at the end of component 3. This will lock these components together. Assemble components 1 and 2 so that the wheel nut socket at the end of component 1 faces upward when seated on component 2.
Page 296: Jacking Instructions
294 IN CASE OF EMERGENCY 2. Turn on the Hazard Warning flashers. WARNING! (Continued) 3. Apply the parking brake. • Turn on the Hazard Warning flasher. • Block the wheel diagonally opposite the wheel to be 4. Place the gear selector in PARK. raised.
Page 297 IN CASE OF EMERGENCY 295 Jack Warning Label Jacking Locations 1. Remove the spare tire, jack, and jack-handle from stow- CAUTION! age. Do not attempt to raise the vehicle by jacking on 2. Loosen, but do not remove, the wheel nuts on the wheel locations other than those indicated in the Jacking with the flat tire.
Page 298 296 IN CASE OF EMERGENCY Front Jacking Location Front Jack Engaged With Jack Handle...
Page 299 IN CASE OF EMERGENCY 297 Rear Jacking Location Rear Jack Engaged With Jack Handle 4. Raise the vehicle by turning the jack screw clockwise with the jack handle. Raise the vehicle until the tire just clears the road surface and enough clearance is obtained to install the spare tire.
Page 300 298 IN CASE OF EMERGENCY WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 5. Remove the wheel nuts. For vehicles so equipped, remove the wheel cover from the wheel by hand.
Page 301: Road Tire Installation
IN CASE OF EMERGENCY 299 12. To stow the winch cable and retainer, fit the assembled WARNING! jack-handle over the winch drive nut. Rotate the jack- handle assembly clockwise until you hear the winch To avoid the risk of forcing the vehicle off the jack, do mechanism click three times.
Page 302 300 IN CASE OF EMERGENCY 3. Align the valve notch in the wheel cover with the valve WARNING! stem on the wheel. Install the cover by hand, snapping the cover over the two lug nuts. Do not use a hammer or To avoid the risk of forcing the vehicle off the jack, do excessive force to install the cover.
Page 303: Spare Tire Stowage
IN CASE OF EMERGENCY 301 7. After 25 miles (40 km), check the lug nut torque with a refer to “Torque Specifications” in “Technical Specifica- torque wrench to ensure that all lug nuts are properly tions”. If in doubt about the correct tightness, have them seated against the wheel.
Page 304: Jump Starting
302 IN CASE OF EMERGENCY Preparations For Jump Start jack-handle assembly until you hear the winch mecha- nism click three times. It cannot be over tightened. Push The battery in your vehicle is located between the left front against the tire several times to be sure it is held securely headlight assembly and the left front wheel splash shield.
Page 305: Jump Starting Procedure
IN CASE OF EMERGENCY 303 4. If using another vehicle to jump start the battery, park WARNING! the vehicle within the jumper cable’s reach, set the parking brake and make sure the ignition is OFF. • Take care to avoid the radiator cooling fan whenever the hood is raised.
Page 306 304 IN CASE OF EMERGENCY Connecting The Jumper Cables 6. Once the engine is started, remove the jumper cables in the reverse sequence: 1. Connect the positive (+) end of the jumper cable to the Disconnecting The Jumper Cables remote positive (+) post of the discharged vehicle. 1.
Page 307: If Your Engine Overheats
IN CASE OF EMERGENCY 305 high. This allows the heater core to act as a supplement CAUTION! to the radiator and aids in removing heat from the engine cooling system. Accessories plugged into the vehicle power outlets draw power from the vehicle’s battery, even when not WARNING! in use (i.e., cellular devices, etc.).
Page 308: 2.4L Engine - If Equipped
306 IN CASE OF EMERGENCY 2.4L Engine — If Equipped 5. Insert a screwdriver or similar small tool into the access port, and push and hold the override release lever On hot days, the engine oil temperature may become too forward.
Page 309: Freeing A Stuck Vehicle
IN CASE OF EMERGENCY 307 FREEING A STUCK VEHICLE information. Once the vehicle has been freed, push the ESC Off switch again to restore ESC On mode. If your vehicle becomes stuck in mud, sand, or snow, it can often be moved using a rocking motion. Turn the steering WARNING! wheel right and left to clear the area around the front wheels.
Page 310: Towing A Disabled Vehicle
308 IN CASE OF EMERGENCY TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service. Towing Condition Wheel OFF The Ground FWD MODELS AWD MODELS Flat Tow NONE IF transmission is oper- NOT ALLOWED able: Wheel Lift Or Dolly Tow...
Page 311: All-Wheel Drive (Awd) Models
IN CASE OF EMERGENCY 309 If the key fob is unavailable, or the vehicle’s battery is CAUTION! discharged, refer to “Gear Selector Override” in this section for instructions on shifting the transmission out of PARK Towing this vehicle in violation of the above require- for towing.
Page 312: Enhanced Accident Response System
310 IN CASE OF EMERGENCY CAUTION! Towing faster than 25 mph (40 km/h) or farther than 15 miles (24 km) with front wheels on the ground can cause severe transmission damage. Damage from im- proper towing is not covered by the New Vehicle Limited Warranty.
Page 313 SERVICING AND MAINTENANCE CONTENTS SCHEDULED SERVICING ....313 ▫ Body Lubrication ..... .327 ▫...
Page 314 312 SERVICING AND MAINTENANCE ▫ Spare Tires — If Equipped ....358 ▫ Protection From Atmospheric Agents ..365 ▫ Wheel And Wheel Trim Care ....360 ▫...
Page 315: Scheduled Servicing
SERVICING AND MAINTENANCE 313 SCHEDULED SERVICING NOTE: Under no circumstances should oil change inter- vals exceed 10,000 miles (16,000 km), twelve months or 350 Your vehicle is equipped with an automatic oil change hours of engine run time, whichever comes first. The 350 indicator system.
Page 316: Maintenance Plan
314 SERVICING AND MAINTENANCE Maintenance Plan Required Maintenance Intervals. Refer to the maintenance plan on the following page for the required maintenance intervals. At Every Oil Change Interval As Indicated By Oil Change Indicator System: • Change oil and filter. •...
Page 317 SERVICING AND MAINTENANCE 315 Mileage or time passed (which- ever comes first) Or Years: Or Kilometers: Additional Inspections Inspect the CV joints. Inspect front suspension, tie rod ends, and replace if necessary. Inspect the brake linings, parking brake function. Additional Maintenance Replace engine air filter.
Page 318 316 SERVICING AND MAINTENANCE Mileage or time passed (which- ever comes first) Or Years: Or Kilometers: Change the automatic transmis- sion fluid and filter. Change the automatic transmis- sion fluid and filter if using your vehicle for any of the following: police, taxi, fleet, or frequent trailer towing.
Page 319 SERVICING AND MAINTENANCE 317 WARNING! WARNING! (Continued) vehicle handling and performance. This could cause • You can be badly injured working on or around a an accident. motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you Heavy Duty Use Of The Vehicle have any doubt about your ability to perform a Change engine oil at 4,000 miles (6,500 km) or 350 hours of...
Page 320: Engine Compartment
318 SERVICING AND MAINTENANCE ENGINE COMPARTMENT 2.4L Engine 1 — Engine Coolant Reservoir 7 — Power Distribution Center (Fuses) 2 — Power Steering Fluid Reservoir 8 — Air Cleaner Filter 3 — Engine Oil Fill 9 — Automatic Transmission Dipstick (4–Speed Only – If Equipped) 4 —...
Page 321: L Engine
SERVICING AND MAINTENANCE 319 3.6L Engine 1 — Engine Coolant Reservoir Pressure Cap 7 — Power Distribution Center (Fuses) 2 — Power Steering Fluid Reservoir 8 — Air Cleaner Filter 3 — Oil Filter Access 9 — Washer Fluid Reservoir 4 —...
Page 322: Checking Oil Level
320 SERVICING AND MAINTENANCE Checking Oil Level CAUTION! (Continued) To assure proper engine lubrication, the engine oil must be to loss of oil pressure and an increase in oil tempera- maintained at the correct level. Check the oil level at ture.
Page 323: Maintenance-Free Battery
SERVICING AND MAINTENANCE 321 The fluid reservoir will hold nearly 1 gal (4 liters) of washer To access the battery, turn the steering wheel fully to the fluid when the message “LoWASH” appears in the instru- right and remove the access panel from the inner fender ment cluster.
Page 324: Dealer Service
322 SERVICING AND MAINTENANCE CAUTION! WARNING! • It is essential when replacing the cables on the You can be badly injured working on or around a battery that the positive cable is attached to the motor vehicle. Only do service work for which you positive post and the negative cable is attached to the have the knowledge and the proper equipment.
Page 325 SERVICING AND MAINTENANCE 323 American Petroleum Institute (API) Engine Oil The engine oil filler cap also shows the recommended Identification Symbol engine oil viscosity for your engine. For information on the engine oil filler cap location, refer to “Engine Compart- ment”...
Page 326: Engine Oil Filter
324 SERVICING AND MAINTENANCE Lubricants which do not have both the engine oil certifi- or governmental agency for advice on how and where used cation mark and the correct SAE viscosity grade number oil and oil filters can be safely discarded in your area. should not be used.
Page 327: Air Conditioner Maintenance
SERVICING AND MAINTENANCE 325 WARNING! WARNING! The air induction system (air cleaner, hoses, etc.) can • Use only refrigerants and compressor lubricants ap- provide a measure of protection in the case of engine proved by the manufacturer for your air conditioning backfire.
Page 328: Accessory Drive Belt Inspection
326 SERVICING AND MAINTENANCE Refrigerant Recovery And Recycling — R–1234yf WARNING! (Continued) R–1234yf Air Conditioning Refrigerant is a hydrofluo- you have any doubt about your ability to perform a roolefin (HFO) that is endorsed by the Environmental service job, take your vehicle to a competent me- Protection Agency and is an ozone-friendly substance with chanic.
Page 329: Body Lubrication
SERVICING AND MAINTENANCE 327 Body Lubrication Conditions that would require replacement: • Rib chunking (one or more ribs has separated from belt Locks and all body pivot points, including such items as body) seat tracks, door hinge pivot points and rollers, liftgate, tailgate, decklid, sliding doors and hood hinges, should be •...
Page 330 328 SERVICING AND MAINTENANCE Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. Avoid using the wiper blades to remove frost or ice from the windshield.
Page 331: Exhaust System
SERVICING AND MAINTENANCE 329 Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle is damaged;...
Page 332 330 SERVICING AND MAINTENANCE keep the engine properly tuned to assure proper catalyst WARNING! (Continued) operation and prevent possible catalyst damage. grass or leaves coming into contact with your exhaust NOTE: Intentional tampering with emissions control sys- system. Do not park or operate your vehicle in areas tems can result in civil penalties being assessed against where your exhaust system can contact anything that you.
Page 333: Cooling System
SERVICING AND MAINTENANCE 331 Cooling System leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. WARNING! Check the coolant recovery bottle tubing for brittle rubber, cracking, tears, cuts, and tightness of the connection at the •...
Page 334 332 SERVICING AND MAINTENANCE Cooling System — Drain, Flush And Refill NOTE: • Mixing of engine coolant (antifreeze) other than speci- NOTE: Some vehicles require special tools to add coolant fied Organic Additive Technology (OAT) engine coolant properly. Failure to fill these systems properly could lead to (antifreeze), may result in engine damage and may severe internal engine damage.
Page 335 SERVICING AND MAINTENANCE 333 • Some vehicles require special tools to add coolant prop- • Mix a minimum solution of 50% OAT engine coolant erly. Failure to fill these systems properly could lead to that meets the requirements of FCA Material Standard severe internal engine damage.
Page 336 334 SERVICING AND MAINTENANCE HOAT and OAT coolant are mixed in an emergency, WARNING! (Continued) have a authorized dealer drain, flush, and refill with • Do not use a pressure cap other than the one speci- OAT coolant (conforming to MS.90032) as soon as pos- fied for your vehicle.
Page 337 SERVICING AND MAINTENANCE 335 3.6L Engine — The level of the coolant in the pressurized • Do not overfill the coolant expansion bottle. coolant bottle should be between the “COLD” and “FULL” • Check the coolant freeze point in the radiator and in the range on the bottle when the engine is cold.
Page 338: Brake System
336 SERVICING AND MAINTENANCE Brake System Overfilling of fluid is not recommended because it may cause leaking in the system. In order to assure brake system performance, all brake system components should be inspected periodically. Refer Fluid level can be expected to fall as the brake pads wear. to the “Maintenance Plan”...
Page 339: Automatic Transmission
SERVICING AND MAINTENANCE 337 for fluid specifications. It is important to maintain the WARNING! (Continued) transmission fluid at the correct level using the recom- in a tightly closed container. Keep the master cylin- mended fluid. der reservoir cap secured at all times. Brake fluid in NOTE: No chemical flushes should be used in any trans- a open container absorbs moisture from the air mission;...
Page 340 338 SERVICING AND MAINTENANCE 6. Remove the dipstick and determine if the fluid is hot or CAUTION! cold. You can also read the transmission fluid tempera- ture using the instrument cluster. Refer to Instrument Do not use chemical flushes in your transmission as Cluster Display in Getting To Know Your Instrument the chemicals can damage your transmission compo- Panel for further information.
Page 341 SERVICING AND MAINTENANCE 339 If the fluid level is low, add fluid through the dipstick tube CAUTION! (Continued) to bring it to the proper level. Do not overfill. After adding shudder, and will require more frequent fluid and any quantity of oil through the dipstick tube, wait at least filter changes.
Page 342: Rear Drive Assembly (Rda) - Awd Models Only
340 SERVICING AND MAINTENANCE fill plug. The fluid level should be maintained between the CAUTION! bottom of the fill hole to 1/8 inch (4 mm) below the fill hole. If a transmission fluid leak occurs, visit an authorized dealer immediately. Severe transmission damage may Add fluid, if necessary, to maintain the proper level.
Page 343: Raising The Vehicle
SERVICING AND MAINTENANCE 341 Frequency Of Fluid Change Tire Markings Refer to the “Maintenance Plan” in this section for the proper maintenance intervals. RAISING THE VEHICLE In the case where it is necessary to raise the vehicle, go to an authorized dealer or service station. TIRES Tire Safety Information Tire safety information will cover aspects of the following...
Page 344 342 SERVICING AND MAINTENANCE NOTE: tires is the same as for P-Metric tires except for the letters “LT” that are molded into the sidewall preceding the • P (Passenger) — Metric tire sizing is based on U.S. size designation. Example: LT235/85R16. design standards.
Page 345 SERVICING AND MAINTENANCE 343 Tire Sizing Chart EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on U.S. design standards, or ..blank..= Passenger car tire based on European design standards, or LT = Light truck tire based on U.S.
Page 346 344 SERVICING AND MAINTENANCE EXAMPLE: H = Speed Symbol – A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under cer- tain operating conditions – The maximum speed corresponding to the speed symbol should only be achieved under specified operating condi- tions (i.e., tire pressure, vehicle loading, road conditions, and posted speed limits) Load Identification: Absence of the following load identification symbols on the sidewall of the tire indicates a Standard Load (SL) tire:...
Page 347 SERVICING AND MAINTENANCE 345 EXAMPLE: – This symbol certifies that the tire is in compliance with the U.S. Department of Transportation tire safety standards and is approved for highway use MA = Code representing the tire manufacturing location (two digits) L9 = Code representing the tire size (two digits) ABCD = Code used by the tire manufacturer (one to four digits) 03 = Number representing the week in which the tire was manufactured (two digits)
Page 348 346 SERVICING AND MAINTENANCE Term Definition Maximum Inflation Pressure The maximum inflation pressure is the maximum permissible cold tire inflation pressure for this tire. The maximum inflation pressure is molded into the sidewall. Recommended Cold Tire Inflation Pressure Vehicle manufacturer’s recommended cold tire inflation pressure as shown on the tire placard.
Page 349 SERVICING AND MAINTENANCE 347 Tire And Loading Information Placard Example Tire Placard Location (B-Pillar) Tire And Loading Information Placard This placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3.
Page 350 348 SERVICING AND MAINTENANCE Loading Steps For Determining Correct Load Limit— The vehicle maximum load on the tire must not exceed the (1) Locate the statement “The combined weight of load carrying capacity of the tire on your vehicle. You will occupants and cargo should never exceed XXX kg or not exceed the tire’s load carrying capacity if you adhere to XXX lbs.”...
Page 351 SERVICING AND MAINTENANCE 349 (5) Determine the combined weight of luggage and NOTE: cargo being loaded on the vehicle. That weight may not • If your vehicle will be towing a trailer, load from your safely exceed the available cargo and luggage load trailer will be transferred to your vehicle.
Page 352: Tires - General Information
350 SERVICING AND MAINTENANCE Tires — General Information WARNING! Tire Pressure Overloading of your tires is dangerous. Overloading Proper tire inflation pressure is essential to the safe and can cause tire failure, affect vehicle handling, and satisfactory operation of your vehicle. Four primary areas increase your stopping distance.
Page 353 SERVICING AND MAINTENANCE 351 • Tread Wear Both under-inflation and over-inflation affect the stability of the vehicle and can produce a feeling of sluggish • Ride Comfort response or over responsiveness in the steering. Safety NOTE: • Unequal tire pressures from side to side may cause WARNING! erratic and unpredictable steering response.
Page 354 352 SERVICING AND MAINTENANCE Tire Inflation Pressures cold tire inflation pressure must not exceed the maximum inflation pressure molded into the tire sidewall. The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or rear edge of the driver’s side door. Check tire pressures more often if subject to a wide range of outdoor temperatures, as tire pressures vary with tem- At least once a month:...
Page 355 SERVICING AND MAINTENANCE 353 may be required for high-speed vehicle operation. Refer to Tire Repair your authorized tire dealer or original equipment vehicle If your tire becomes damaged, it may be repaired if it meets dealer for recommended safe operating speeds, loading the following criteria: and cold tire inflation pressures.
Page 356 354 SERVICING AND MAINTENANCE See the tire pressure monitoring section for more informa- tion. Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping. Refer to “Freeing A Stuck Vehicle”...
Page 357 SERVICING AND MAINTENANCE 355 Life Of Tire Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with The service life of a tire is dependent upon varying factors oil, grease, and gasoline. including, but not limited to: Replacement Tires •...
Page 358: Tire Types
356 SERVICING AND MAINTENANCE It is recommended you contact your authorized tire dealer WARNING! (Continued) or original equipment dealer with any questions you may • Failure to equip your vehicle with tires having ad- have on tire specifications or capability. Failure to use equate speed capability can result in sudden tire equivalent replacement tires may adversely affect the failure and loss of vehicle control.
Page 359 SERVICING AND MAINTENANCE 357 Summer Or Three Season Tires — If Equipped Snow Tires Summer tires provide traction in both wet and dry condi- Some areas of the country require the use of snow tires tions, and are not intended to be driven in snow or on ice. during the Winter.
Page 360: Spare Tires - If Equipped
358 SERVICING AND MAINTENANCE Spare Tires — If Equipped Compact Spare Tire — If Equipped The compact spare is for temporary emergency use only. NOTE: For vehicles equipped with Tire Service Kit instead You can identify if your vehicle is equipped with a compact of a spare tire, please refer to “Tire Service Kit”...
Page 361 SERVICING AND MAINTENANCE 359 Do not install a wheel cover or attempt to mount a WARNING! conventional tire on the collapsible spare wheel, since the wheel is designed specifically for the collapsible spare tire. Compact and collapsible spares are for temporary emergency use only.
Page 362: Wheel And Wheel Trim Care
360 SERVICING AND MAINTENANCE Wheel And Wheel Trim Care Limited Use Spare — If Equipped The limited use spare tire is for temporary emergency use All wheels and wheel trim, especially aluminum and chrome only. This tire is identified by a label located on the limited plated wheels, should be cleaned regularly using mild (neutral use spare wheel.
Page 363: Tire Chains (Traction Devices)
SERVICING AND MAINTENANCE 361 When cleaning extremely dirty wheels including excessive Dark Vapor Chrome, Black Satin Chrome, or Low Gloss brake dust, care must be taken in the selection of tire and Clear Coat Wheels wheel cleaning chemicals and equipment to prevent dam- CAUTION! age to the wheels.
Page 364: Tire Rotation Recommendations
362 SERVICING AND MAINTENANCE WARNING! CAUTION! (Continued) • Observe the traction device manufacturer’s instruc- Using tires of different size and type (M+S, Snow) tions on the method of installation, operating speed, between front and rear axles can cause unpredictable and conditions for use. Always use the suggested handling.
Page 365 SERVICING AND MAINTENANCE 363 The suggested Front Wheel Drive (FWD) rotation method is the “forward cross” shown in the following diagram. This rotation pattern does not apply to some directional tires that must not be reversed. All Wheel Drive (AWD) Tire Rotation CAUTION! Proper operation of All Wheel Drive vehicles depends Front Wheel Drive (FWD) Tire Rotation...
Page 366: Department Of Transportation Uniform
364 SERVICING AND MAINTENANCE DEPARTMENT OF TRANSPORTATION UNIFORM Traction Grades TIRE QUALITY GRADES The Traction grades, from highest to lowest, are AA, A, The following tire grading categories were established B, and C. These grades represent the tire’s ability to stop by the National Highway Traffic Safety Administration.
Page 367: Bodywork
SERVICING AND MAINTENANCE 365 corresponds to a level of performance, which all pas- which exposes your vehicle to airborne contaminants, road senger vehicle tires must meet under the Federal Motor surfaces on which the vehicle is operated, extreme hot or Vehicle Safety Standard No.
Page 368: Body And Underbody Maintenance
366 SERVICING AND MAINTENANCE Body And Underbody Maintenance • Use a high quality cleaner wax, such as Mopar Cleaner Wax to remove road film, stains and to protect your Cleaning Headlights paint finish. Take care never to scratch the paint. Your vehicle is equipped with plastic headlights and fog •...
Page 369: Interiors
SERVICING AND MAINTENANCE 367 • If your vehicle is damaged due to a collision or similar Seat Belt Maintenance cause that destroys the paint and protective coating, have Do not bleach, dye, or clean the belts with chemical your vehicle repaired as soon as possible. The cost of such solvents or abrasive cleaners.
Page 370: Plastic And Coated Parts
368 SERVICING AND MAINTENANCE Plastic And Coated Parts Leather Parts Use Mopar Total Clean to clean vinyl upholstery. Mopar Total Clean is specifically recommended for leather upholstery. CAUTION! Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can •...
Page 371: Glass Surfaces
SERVICING AND MAINTENANCE 369 CAUTION! Do not use Alcohol and Alcohol-based and/or Ketone based cleaning products to clean leather seats, as damage to the seat may result. Glass Surfaces All glass surfaces should be cleaned on a regular basis with Mopar Glass Cleaner, or any commercial household-type glass cleaner.
Page 373 TECHNICAL SPECIFICATIONS CONTENTS IDENTIFICATION DATA....372 FLEXIBLE FUEL (3.6L ENGINE ONLY) ..378 ▫ Vehicle Identification Number ... . .372 ▫...
Page 374: Identification Data
372 TECHNICAL SPECIFICATIONS IDENTIFICATION DATA Vehicle Identification Number The Vehicle Identification Number (VIN) is on the left front corner of the instrument panel and is visible from outside of the vehicle through the windshield. This number also appears stamped on the right front door sill under the sill moulding and printed on the Automobile Information Disclosure Label affixed to a window on your vehicle, the vehicle registration and title.
Page 375: Wheel And Tire Torque Specifications
TECHNICAL SPECIFICATIONS 373 WHEEL AND TIRE TORQUE SPECIFICATIONS hydraulic system, the “Brake Warning Light” will turn on as the brake fluid level drops in the master cylinder. Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle. Any time a In the event power assist is lost for any reason (i.e., wheel has been removed and reinstalled on the vehicle, the repeated brake applications with the engine OFF) the...
Page 376 374 TECHNICAL SPECIFICATIONS Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles. Torque Patterns After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against Wheel Mounting Surface the wheel.
Page 377: Fuel Requirements
TECHNICAL SPECIFICATIONS 375 FUEL REQUIREMENTS Reformulated Gasoline Many areas of the country require the use of cleaner These engines are designed to meet all burning gasoline referred to as “Reformulated Gasoline”. emissions regulations and provide opti- Reformulated gasoline contains oxygenates and are specifi- mum fuel economy and performance cally blended to reduce vehicle emissions and improve air when using high quality unleaded...
Page 378: Gasoline/Oxygenate Blends
376 TECHNICAL SPECIFICATIONS Designated TOP TIER Detergent Gaso- CAUTION! (Continued) line contains a higher level of detergents cause emissions to exceed the applicable standard, to further aide in minimizing engine and/or cause the “Malfunction Indicator Light” to and fuel system deposits. When avail- illuminate.
Page 379: Cng And Lp Fuel System Modifications
TECHNICAL SPECIFICATIONS 377 Fuel System Cautions • Poor cold start and cold drivability. • Increased risk for fuel system component corrosion. CAUTION! CNG And LP Fuel System Modifications Follow these guidelines to maintain your vehicle’s Modifications that allow the engine to run on compressed performance: natural gas (CNG) or liquid propane (LP) may result in •...
Page 380: Carbon Monoxide Warnings
378 TECHNICAL SPECIFICATIONS FLEXIBLE FUEL (3.6L ENGINE ONLY) NOTE: Intentional tampering with the emissions control system can result in civil penalties being assessed against E-85 General Information you. The information in this section is unique for Flexible Fuel Carbon Monoxide Warnings vehicles only.
Page 381: Fuel Requirements
TECHNICAL SPECIFICATIONS 379 NOTE: WARNING! (Continued) • Use seasonally adjusted E-85 fuel (ASTM D5798). With materials lit or products that can cause spark in or near non-seasonally adjusted E-85 fuel, hard starting and the vehicle when removing the fuel filler tube cap (gas rough idle following start up may be experienced even if cap) or filling the tank.
Page 382: Starting
380 TECHNICAL SPECIFICATIONS Starting Replacement Parts The characteristics of E-85 fuel make it unsuitable for use All fuel and engine components in your Flexible Fuel when ambient temperatures fall below 0°F (-18°C). In the Vehicle (FFV) are designed to be compatible with ethanol. range of 0°F (-18°C) to 32°F (0°C), an increase in the time it Ethanol compatible service components are required.
Page 383: Fluid Capacities
TECHNICAL SPECIFICATIONS 381 FLUID CAPACITIES U.S. Metric Fuel (Approximate) Front Wheel Drive (FWD) Models 20.5 Gallons 77.6 Liters All-Wheel Drive Models 21.1 Gallons 79.8 Liters Engine Oil With Filter 2.4L Engine (SAE 5W-20, API Certified) 4.5 Quarts 4.26 Liters 3.6L Engine (SAE 5W-20, API Certified) 6 Quarts 5.6 Liters Cooling System*...
Page 384: Fluids And Lubricants
382 TECHNICAL SPECIFICATIONS FLUIDS AND LUBRICANTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend you use Mopar Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Tech- nology). Engine Oil We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the requirements of FCA Material Standard MS-6395 such as Mopar, Pennzoil, and Shell Helix.
Page 385 TECHNICAL SPECIFICATIONS 383 CAUTION! CAUTION! (Continued) and refilled with fresh OAT coolant (conforming to • Mixing of engine coolant (antifreeze) other than MS.90032), by an authorized dealer as soon as pos- specified Organic Additive Technology (OAT) en- sible. gine coolant (antifreeze), may result in engine dam- •...
Page 386: Chassis
384 TECHNICAL SPECIFICATIONS Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission Use only ATF+4 Automatic Transmission Fluid. Failure to use ATF+4 fluid may affect the function or per- formance of your transmission. We recommend Mopar ATF+4 fluid. Power Transfer Unit (PTU) We recommend you use Mopar Gear Lubricant 75W-90.
Page 387 MULTIMEDIA CONTENTS UCONNECT RADIOS ....387 UCONNECT MULTIMEDIA — VIDEO ENTERTAINMENT SYSTEM (VES) — CYBERSECURITY ......387 IF EQUIPPED .
Page 388 386 MULTIMEDIA ▫ VES Headphones Operation ....424 UCONNECT PHONE (UCONNECT 3/3 NAV) . . .452 ▫ Controls ......424 ▫...
Page 389: Uconnect Radios
MULTIMEDIA UCONNECT RADIOS The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent For detailed information about your Uconnect radio, refer version of vehicle software (such as Uconnect software) is to your Uconnect Owner’s Manual Supplement. installed.
Page 390: Uconnect Settings
388 MULTIMEDIA UCONNECT SETTINGS NOTE: • FCA or your dealer may contact you directly regarding The Uconnect system uses a combination of buttons on the software updates. touchscreen and buttons on the faceplate located on the center of the instrument panel that allows you to access •...
Page 391 MULTIMEDIA Push the SETTINGS button on the faceplate to access the Settings screen, use the “Page Up”/“Page Down” buttons on the touchscreen to scroll through the following settings. Press the desired setting button on the touchscreen to change the setting using the description shown on the following pages for each setting.
Page 392 390 MULTIMEDIA Display After pressing the “Display” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Brightness – NOTE: The “Brightness” setting can also be adjusted by selecting any point on the scale between the “+” and “–” buttons on the touchscreen.
Page 393: Gear Selector
MULTIMEDIA Clock After pressing the “Clock & Date” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Set Time and Format 12 hour 24 hour NOTE: Within the “Set Time and Format” setting, press the corresponding arrow buttons on the touchscreen to adjust to the correct time.
Page 394 392 MULTIMEDIA Setting Name Selectable Options Hill Start Assist — If Equipped Lights After pressing the “Lights” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Headlight Off Delay — 0 sec 30 sec 60 sec 90 sec If Equipped NOTE:...
Page 395 MULTIMEDIA Setting Name Selectable Options NOTE: When the “Automatic High Beam Headlamps” is selected, the high beam headlights will activate/deactivate auto- matically under certain conditions. Daytime Running Lights Steering Directed Lights — If Equipped NOTE: When the “Steering Directed Lights” feature is selected, the headlights will turn relative to a change in direction of the steering wheel.
Page 396 394 MULTIMEDIA Setting Name Selectable Options Auto Unlock On Exit NOTE: When the “Auto Unlock On Exit” feature is selected, all doors will unlock when the vehicle is stopped and the trans- mission is in the PARK or NEUTRAL position and the driver’s door is opened. Flash Lights With Lock Sound Horn With Lock Sound Horn With Remote Start...
Page 397 MULTIMEDIA Auto-On Comfort & Remote Start After pressing the “Auto-On Comfort & Remote Start” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Auto-On Driver Heated Seat & Steering Wheel With Vehicle Start— If Equipped NOTE: When this feature is selected the driver’s heated seat and heated steering wheel (if equipped) will automatically turn on when temperatures are below 40°...
Page 398 396 MULTIMEDIA Setting Name Selectable Options Headlight Off Delay 0 sec 30 sec 60 sec 90 sec NOTE: When the “Headlight Off Delay” feature is selected, it allows the adjustment of the amount of time the headlights remain on after the engine is shut off. Compass Settings After pressing the “Compass Settings”...
Page 399 MULTIMEDIA Setting Name Selectable Options NOTE: Press “Compass Calibration” on the touchscreen to enter calibration. To start calibration of the compass, press the “Yes” button on the touchscreen and complete one or more 360-degree turns (in an area free from large metal or me- tallic objects).
Page 400 398 MULTIMEDIA Audio After pressing the “Audio” button on the touchscreen, the following settings will be available: Setting Name Adjustable Options Equalizer Bass Treble NOTE: When in this display you may adjust the “Bass”, “Mid”, and “Treble” settings. Adjust the settings with the “+” and “–”...
Page 401 MULTIMEDIA Phone/Bluetooth After pressing the “Phone/Bluetooth” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Paired Phones List of Paired Phones NOTE: This feature shows which phones are paired to the Phone/Bluetooth system. For further information, refer to the Uconnect Owner’s Manual Supplement.
Page 402: Customer Programmable Features - Uconnect 3/3
400 MULTIMEDIA Setting Name Selectable Options Subscription Info Sirius ID NOTE: New vehicle purchasers or lessees will receive a free limited time subscription to SiriusXM Satellite Radio with your radio. Following the expiration of the free services, it will be necessary to access the information on the Subscription Information screen to re-subscribe.
Page 403 MULTIMEDIA Press the “More” button on the touchscreen, then press the Once the setting is complete press the Back Arrow button “Settings” button on the touchscreen to display the menu on the touchscreen to return to the previous menu or press setting screen.
Page 404 402 MULTIMEDIA Display After pressing the Display button on the touchscreen, the following settings will be available: Setting Name Selectable Options Display Mode Night Auto Display Brightness With Headlights ON NOTE: To make changes to the Display Brightness with Headlights ON setting, the headlights must be on and the interior dimmer switch must not be in the party or parade positions.
Page 405 MULTIMEDIA Setting Name Selectable Options Units Metric Voice Response Length Brief Detailed Touchscreen Beep Navigation Turn-By-Turn In Cluster — If Equipped NOTE: When the “Navigation Turn-By-Turn In Cluster” feature is selected, the turn-by-turn directions will appear in the in- strument cluster display as the vehicle approaches a designated turn within a programmed route. Fuel Saver Display In Clus- ter —...
Page 406 404 MULTIMEDIA Clock After pressing the Clock button on the touchscreen, the following settings will be available. Setting Name Selectable Options Sync Time With GPS — If Equipped Set Time Hours NOTE: This feature will allow you to adjust the hours. The “Sync time with GPS” button on the touchscreen must be un- checked.
Page 407 MULTIMEDIA Safety & Driving Assistance After pressing the Safety/Assistance button on the touch- screen, the following settings will be available: Setting Name Selectable Options Park Assist — If Equipped Sound Only Sounds and Display NOTE: The Rear Park Assist system will scan for, and the alert the driver of, objects behind the vehicle when the transmis- sion gear selector is in REVERSE and the vehicle speed is less than 11 mph (18 km/h).
Page 408 406 MULTIMEDIA Lights After pressing the Lights button on the touchscreen, the following settings will be available: Setting Name Selectable Options Headlight Off Delay 0 sec 30 sec 60 sec 90 sec NOTE: When the “Headlight Off Delay” feature is selected, it allows the adjustment of the amount of time the headlights remain on after the engine is shut off.
Page 409 MULTIMEDIA Setting Name Selectable Options Auto Dim High Beams— If Equipped NOTE: When the “Auto Dim High Beams” feature is selected, the high beam headlights will activate/deactivate automati- cally under certain conditions. Daytime Running Lights — If Equipped Steering Directed Headlights —...
Page 410 408 MULTIMEDIA Doors & Locks After pressing the Doors & Locks button on the touch- screen, the following settings will be available: Setting Name Selectable Options Auto Door Locks — If Equipped NOTE: When the “Auto Door Locks” feature is selected, all doors will lock automatically when the vehicle reaches a speed of 12 mph (20 km/h).
Page 411 MULTIMEDIA Setting Name Selectable Options Sound Horn With Remote Start 1st Press Of Key Fob Unlocks Driver Door All Doors NOTE: When Driver Door is selected with 1st Press Of Key Fob Unlocks, only the driver’s door will unlock with the first press of the key fob unlock button.
Page 412 410 MULTIMEDIA Auto-On Comfort & Remote Start After pressing the Auto-On Comfort & Remote Start button on the touchscreen, the following settings will be available: Setting Name Selectable Options Auto-On Driver Heated Seat & Steering Wheel With Vehicle Start— If Equipped NOTE: When this feature is selected the driver’s heated seat and heated steering wheel (if equipped) will automatically turn ON when temperatures are below 40°...
Page 413 MULTIMEDIA Setting Name Selectable Options NOTE: When the “Engine Off Power Delay” feature is selected, the power window switches, radio, Uconnect phone system (if equipped), DVD video system (if equipped), power sunroof (if equipped), and power outlets will remain active for up to ten minutes after the ignition is cycled to OFF.
Page 414 412 MULTIMEDIA Setting Name Selectable Options Perform Com- Start pass Calibra- tion NOTE: To start calibration of the compass, press the “Start” button on the touchscreen and complete one or more 360-degree turns (in an area free from large metal or metallic objects). A message will appear on the touchscreen when the com- pass has been successfully calibrated.
Page 415 MULTIMEDIA Audio After pressing the Audio button on the touchscreen, the following settings will be available. Setting Name Adjustable Options Equalizer Bass Treble NOTE: When in this display you may adjust the “Bass”, “Mid”, and “Treble” settings. Adjust the settings with the “+” and “–”...
Page 416 414 MULTIMEDIA Setting Name Adjustable Options Auto Play NOTE: When the “Auto Play” feature is on, music will begin playing music automatically whenever an audio device is connected and recognized. Phone/Bluetooth After pressing the “Phone/Bluetooth” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Paired Devices...
Page 417 MULTIMEDIA Setting Name Selectable Options NOTE: SiriusXM can be programmed to designate a group of channels that are the most desirable to listen to or to exclude undesirable channels while scanning. This feature allows you to select the channels you would like to skip. Subscription Info Sirius ID NOTE:...
Page 418: Steering Wheel Audio Controls
416 MULTIMEDIA Accessibility — If Equipped After pressing the “Accessibility” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Accessibility NOTE: The “Accessibility” feature announces a function prior to performing the action selected when using DVD functions, when it is activated.
Page 419: Right-Hand Switch Functions
MULTIMEDIA Right-Hand Switch Functions • Push the button located in the center of the switch to change to the next preset that you have programmed. • Push the top of the switch to increase the volume. • Push the bottom of the switch to decrease the volume. IPOD/USB/MP3 CONTROL •...
Page 420: Getting Started
418 MULTIMEDIA Getting Started Single Video Screen • Screen located in the overhead console: Unfold the NOTE: Typically there are two different ways to operate overhead LCD screen by pushing the button on the the features of the Video Entertainment System (VES). overhead console behind the screen.
Page 421: Listen To An Audio Source On Channel 2 While A
MULTIMEDIA Audio/Video RCA Jacks (AUX Jacks) on the rear of the Using The Touchscreen Radio Controls center console enable the monitor to display video directly 1. Press the “MORE” button on the touchscreen. from a video camera, connect video games for display on the screen, or play music directly from an MP3 player.
Page 422: Play A Dvd Using The Touchscreen Radio
420 MULTIMEDIA 2. While looking at the video screen, either press Up/ 2. While looking at the Video Screen, highlight DISC by Down/Left/Right on the Remote Control to highlight either pushing Up/Down/Left/Right buttons or by the desired audio source or repeatedly push the MODE repeatedly pushing the MODE button, then push EN- button on the remote until the desired audio source TER.
Page 423: Ves Remote Control - If Equipped
MULTIMEDIA VES Remote Control — If Equipped 2. Channel Selector Indicators – When a button is pushed, the currently affected channel or channel button is illuminated momentarily. 3. Light – Turns the remote control backlighting on or off. The remote backlighting turns off automatically after five seconds.
Page 424 422 MULTIMEDIA 7. MENU – Push to return to the main menu of a DVD settings section) to access the DVD setup menu, select disc, to select a satellite audio or video channel from the the menu button on the radio. When a disc is loaded in Station list, or select playback modes (SCAN/ the DVD player (if equipped) and the VES mode is RANDOM for a CD).
Page 425: Remote Control Storage
MULTIMEDIA Remote Control Storage Locking The Remote Control The video screen comes with a built in storage compart- All remote control functionality can be disabled as a ment for the remote control which is accessible when the parental control feature. screen is opened.
Page 426: Important Notes For Single Video Screen System
424 MULTIMEDIA Important Notes For Single Video Screen System • VES is able to transmit two channels of stereo audio simultaneously. • In split screen mode the left side equates to Channel 1 and right side equates to Channel 2. •...
Page 427: Replacing The Headphone Batteries
MULTIMEDIA Changing The Audio Mode For Headphones 5. To cancel out of the Mode Selection menu, push the BACK button on the remote control. 1. Ensure the Remote Control channel/screen selector Replacing The Headphone Batteries switch is in the same position as the headphone selector switch.
Page 428: Unwired Stereo Headphone Lifetime Limited Warranty
426 MULTIMEDIA Unwired Stereo Headphone Lifetime Limited states and jurisdictions may not allow the exclusion or Warranty limitation of incidental or consequential damages, so the above limitation may not apply to you. This warranty gives Who Does This Warranty Cover? This warranty covers the you specific legal rights.
Page 429: System Information
MULTIMEDIA System Information When in shared disc both the radio and the VES have control of the video functions. The VES has the ability to Shared Modes control the following video modes: This allows the VES to output radio sources to the head- NOTE: phones and the radio to output VES sources to the vehicle •...
Page 430 428 MULTIMEDIA When information mode is active, the current mode setting 5. Remote Locked Out — When the icon is displayed, the for both audio channels is displayed. In addition to the remote control functions are disabled. items called out by number, the remaining information 6.
Page 431 MULTIMEDIA When the display for either Channel 1 or Channel 2 shows Disc Menu DIRECT TUNE, pushing the remote control’s ENTER but- When listening to a CD Audio or CD Data disc, pushing ton activates a numeric keypad menu. This screen makes it the remote control’s MENU button displays a list of all easy to enter a specific tuner frequency or track number.
Page 432 430 MULTIMEDIA To change the settings, push the remote control’s naviga- 3. To change the current audio mode, push the remote tion buttons to select an item, then push the remote control’s MODE button. This will automatically select control’s navigation buttons to change the value for the the next available audio mode without using the currently selected item.
Page 433 MULTIMEDIA DVD Region Codes If you record a disc using a personal computer, there may be cases where the DVD player may not be able to play The DVD player and many DVD discs are coded by some or the entire disc, even if it is recorded in a compat- geographic region.
Page 434 432 MULTIMEDIA • Any file that is copy protected (such as those down- The recommended method for labeling recordable discs (CD-R, CD-RW, DVD-R and DVD-RW) is with a permanent loaded from many online music stores) will not play. The marker. Do not use adhesive labels as they may separate DVD player will automatically skip the file and begin from the disc, become stuck, and cause permanent damage playing the next available file.
Page 435: Uconnect Phone (4.3)
MULTIMEDIA Disc Errors for home or other limited viewing uses otherwise autho- rized by Macrovision. Reverse engineering or disassembly If the DVD player is unable to read the disc, a Disc Error is prohibited. message is displayed on the Radio display and the disc is automatically ejected.
Page 436 434 MULTIMEDIA • View Call logs on screen (“Show incoming calls,” “Show For Uconnect Customer Support: Outgoing calls,” “Show missed Calls,” “Show Recent • U.S. residents – visit UconnectPhone.com or call 1-877- Calls”) 855-8400. • Searching Contacts phone number (“Search for John •...
Page 437: Operation
MULTIMEDIA The Uconnect Phone is driven through your Bluetooth Uconnect Voice Command Button “Hands-Free Profile” mobile phone. Uconnect features The Uconnect Voice Command Button is Bluetooth technology - the global standard that enables only used for “barge in” and when you are different electronic devices to connect to each other with- already in a call and you want to send Tones or out wires or a docking station, so Uconnect Phone works...
Page 438 436 MULTIMEDIA You will be prompted for a specific command and then Natural Speech guided through the available options. Your Uconnect Phone Voice system uses a Natural Lan- • Prior to giving a voice command, one must wait for the guage Voice Recognition (VR) engine.
Page 439 MULTIMEDIA Voice Command Tree To complete the pairing process, you will need to reference your mobile phone Owner’s Manual. The Uconnect web- Refer to “Voice Tree” in this section. site may also provide detailed instructions for pairing. Help Command NOTE: If you need assistance at any prompt, or if you want to •...
Page 440 438 MULTIMEDIA 2. At the Paired Phones screen press the “Add Device” 7. When the pairing process has successfully completed, button on the touchscreen and a pop-up with instruc- the system will prompt you to choose whether or not tions will appear. this is your favorite device.
Page 441 MULTIMEDIA 4. At the Options pop-up screen press the “Connect De- Making A Phone Or Audio Device A Favorite vice” button on the touchscreen. 1. Push the SETTINGS button on the faceplate. 5. Press the “X” to exit out of the Settings screen. 2.
Page 442: Phone Call Features
440 MULTIMEDIA • Automatic download and update of a phone book, if To change the 911/Help number, follow these steps: supported, begins as soon as the Bluetooth wireless 1. Press the “Phonebook” button on the touchscreen from phone connection is made to the Uconnect Phone, for the Phone main screen.
Page 443 MULTIMEDIA Ways To Initiate A Phone Call 2. After the “Listening” prompt and the following beep, say “Call John Doe Mobile.” Listed below are all the ways you can initiate a phone call with Uconnect Phone. 3. The Uconnect Phone will dial the number associated with John Doe, or if there are multiple numbers it will •...
Page 444 442 MULTIMEDIA 3. The Touch-Tone screen will be displayed. NOTE: Incoming can also be replaced with “Outgoing”, “Recent” or “Missed.” 4. Use the numbered buttons on the touchscreen to enter the number and press “Call.” Answer Or Reject An Incoming Call — No Call Currently In Progress To send a touch tone using Voice Recognition (VR), push the Voice Command...
Page 445 MULTIMEDIA Making A Second Call While Current Call Is In Join Calls Progress When two calls are in progress (one active and one on To make a second call while you are currently on a call, hold), press the “Join Calls” button on the Phone main push the Voice Command button and say “Dial”...
Page 446: Uconnect Phone Features
444 MULTIMEDIA • After the “Listening” prompt and the following beep, Call Continuation say “Emergency” and the Uconnect Phone will instruct Call continuation is the progression of a phone call on the the paired mobile phone to call the emergency number. Uconnect Phone after the vehicle ignition key has been This feature is supported in the U.S., Canada, and switched to OFF.
Page 447 MULTIMEDIA Roadside Assistance/Towing Assistance You can use your Uconnect Phone to access a voice mail system or an automated service, such as a paging service or If you need roadside/towing assistance: automated customer service line. Some services require • Push the Phone button to begin.
Page 448 446 MULTIMEDIA You can also send stored mobile phonebook entries as Barge In — Overriding Prompts tones for fast and easy access to voice mail and pager The Voice Command button can be used when you entries. For example, if you previously created a Phone- wish to skip part of a prompt and issue your voice book entry and/or Last Name as “Voice Password,”...
Page 449: Advanced Phone Connectivity
MULTIMEDIA Phone And Network Status Indicators Mute/Un-Mute (Mute OFF) Uconnect Phone will provide notification to inform you of When you mute the Uconnect Phone, you will still be able your phone and network status when you are attempting to hear the conversation coming from the other party, but to make a phone call using Uconnect Phone.
Page 450: Things You Should Know About Your Uconnect Phone
448 MULTIMEDIA Things You Should Know About Your Uconnect NOTE: Phone • Even though the system is designed for users speaking in North American English, French, and Spanish accents, Voice Command the system may not always work for some. For best performance: •...
Page 451 MULTIMEDIA Far End Audio Performance Bluetooth Communication Link Audio quality is maximized under: Mobile phones have been found to lose connection to the Uconnect Phone. When this happens, the connection can • Low-to-medium blower setting generally be reestablished by switching the phone off/on. •...
Page 452 450 MULTIMEDIA Voice Tree...
Page 453: General Information
MULTIMEDIA NOTE: • Available Voice Commands are shown in bold face and underlined in the gray shaded boxes. • You can replace “John Smith” with any name in your mobile or favorite phone book. You can also say “Send a General Information message to John Smith”...
Page 454: Uconnect Phone (Uconnect 3/3 Nav)
452 MULTIMEDIA UCONNECT PHONE (UCONNECT 3/3 NAV) Screen Activated Features • Dialing via Keypad using touchscreen. Uconnect Phone is a voice-activated, hands-free, in-vehicle communications system. Uconnect Phone allows you to • Viewing and Calling contacts from Phonebooks dis- dial a phone number with your mobile phone. played on the touchscreen.
Page 455 MULTIMEDIA NOTE: Your phone must be capable of SMS messaging via The Uconnect Phone is driven through your Bluetooth Bluetooth for messaging features to work properly. Your “Hands-Free Profile” mobile phone. Uconnect features mobile phone’s audio is transmitted through your vehicles Bluetooth technology - the global standard that enables audio system;...
Page 456: Operation
454 MULTIMEDIA 2. Say the individual commands and allow the system to Uconnect Voice Command Button guide you to complete the task. The Uconnect Voice Command button is You will be prompted for a specific command and then only used for “barge in” and when you are guided through the available options.
Page 457 MULTIMEDIA Natural Speech Help Command Your Uconnect Phone Voice system uses a Natural Lan- If you need assistance at any prompt, or if you want to guage Voice Recognition (VR) engine. know your options at any prompt, say “Help” following the beep.
Page 458 456 MULTIMEDIA Pair (Link) Uconnect Phone To A Mobile Phone To begin using your Uconnect Phone, you must pair your compatible Bluetooth enabled mobile phone. NOTE: • You must have Bluetooth enabled on your mobile phone to complete this procedure. •...
Page 459 MULTIMEDIA • Search for available devices on your Bluetooth enabled 5. When the pairing process has successfully completed, mobile phone. When prompted on the phone, enter the the system will prompt you to choose whether or not name and PIN shown on the Uconnect screen. this is your favorite phone.
Page 460 458 MULTIMEDIA You can also use the following VR commands to bring up 7. When the pairing process has successfully completed, the Paired Phone screen from any screen on the radio: the system will prompt you to choose whether or not this is your favorite device.
Page 461 MULTIMEDIA 3. Press to select the particular Phone or the particular 3. Press the settings icon button located to the right of the Audio Device. device name for a different Phone or Audio Device than the currently connected device. 4. Press the “X” to exit out of the Settings screen. 4.
Page 462 460 MULTIMEDIA • Depending on the maximum number of entries down- Phonebook Download (Automatic Phonebook Transfer From Mobile Phone) — If Equipped loaded, there may be a short delay before the latest downloaded names can be used. Until then, if available, If equipped and specifically supported by your phone, the previously downloaded phonebook is available for Uconnect Phone automatically downloads names (text...
Page 463 MULTIMEDIA 2. After loading the mobile phonebook, select Phonebook the touchscreen and then select the “+” button on the from the Phone main screen, then select the appropriate touchscreen located to the right of the phonebook re- number. Press the “+” next to the selected number to cord.
Page 464 462 MULTIMEDIA To Remove A Favorite 4. The Options pop-up will display, press “Remove from Favs.” 1. To remove a Favorite, select phonebook from the Phone main screen. Emergency And Towing Assistance The Emergency and Towing Assistance Favorite numbers 2. Next select Favorites on the left side of the screen and can only be altered.
Page 465: Phone Call Features
MULTIMEDIA Ways To Initiate A Phone Call Listed below are all the ways you can initiate a phone call with Uconnect Phone. • Redial • Dial by pressing in the number • Voice Commands (Dial by Saying a Name, Call by Saying a Phonebook Name, Redial or Call Back) •...
Page 466 464 MULTIMEDIA • Transfer the call to/from the phone Call By Saying A Phonebook Name • Swap two active calls 1. Push the “VR” button on your steering wheel to begin. • Join two active calls together 2. After the “Listening” prompt and the following beep, say “Call John Doe Mobile.”...
Page 467 MULTIMEDIA Recent Calls • Missed Calls You may browse up to 34 of the most recent of each of the • All Calls following call types: These can be accessed by pressing the “recent calls” button on the touchscreen on the Phone main screen. You can also push the Phone button and say “Show my incoming calls”...
Page 468 466 MULTIMEDIA Answer Or Ignore An Incoming Call — Call Place/Retrieve A Call From Hold Currently In Progress During an active call, press the “Hold” button on the If a call is currently in progress and you have another Phone main screen. incoming call, you will hear the same network tones for Toggling Between Calls call waiting that you normally hear when using your...
Page 469: Uconnect Phone Features
MULTIMEDIA Redial If the phone is not reachable and the Uconnect Phone is operational, you may reach the emergency number as Press the “Redial” button on the touchscreen, or push the follows: “VR” button and after the “Listening” prompt and the following beep, say “Redial.”...
Page 470 468 MULTIMEDIA Voice Mail Calling WARNING! To learn how to access your voice mail, refer to “Working Your phone must be turned on and connected to the with Automated Systems.” Uconnect Phone to allow use of this vehicle feature in Working With Automated Systems emergency situations, when the mobile phone has network coverage and stays connected to the Uconnect...
Page 471 MULTIMEDIA You can also send stored mobile phonebook entries as Barge In — Overriding Prompts tones for fast and easy access to voice mail and pager The Voice Command button can be used when you entries. For example, if you previously created a Phone- wish to skip part of a prompt and issue your voice book entry with First and/or Last Name as “Voicemail command immediately.
Page 472: Advanced Phone Connectivity
470 MULTIMEDIA Phone And Network Status Indicators Mute/Un-Mute (Mute ON/OFF) Uconnect Phone will provide notification to inform you of When you mute the Uconnect Phone, you will still be able your phone and network status when you are attempting to hear the conversation coming from the other party, but to make a phone call using Uconnect Phone.
Page 473: Things You Should Know About Your Uconnect Phone
MULTIMEDIA Things You Should Know About Your Uconnect WARNING! Phone ALWAYS drive safely with your hands on the wheel. Voice Command You have full responsibility and assume all risks For the best performance: related to the use of the Uconnect features and appli- cations in this vehicle.
Page 474 472 MULTIMEDIA Far End Audio Performance Your phone must support SMS over Bluetooth to use this feature. If the Uconnect Phone determines your phone is Audio quality is maximized under: not compatible with SMS messaging over Bluetooth the • Low-To-Medium Blower Setting “Messaging”...
Page 475 MULTIMEDIA Read Messages: Send Messages Using Buttons On The Touchscreen: You can send messages using Uconnect Phone. To send a If you receive a new text message while your phone is new message: connected to Uconnect Phone, an announcement will be made to notify you that you have a new text message.
Page 476 474 MULTIMEDIA 4. If multiple numbers are available for the contact select which number you would like to have the message sent. 5. Press “Send” or “Cancel.” Send Messages Using Voice Commands: 1. Push the Phone button. 2. After the “Listening” prompt and the following beep, say “Send message to John Smith mobile.”...
Page 477 MULTIMEDIA List of Preset Messages: 14. Where are you? 1. Yes. 15. Are you there yet? 2. No. 16. I need directions. 3. Okay. 17. I’m lost. 4. I can’t talk right now. 18. See you later. 5. Call me. Bluetooth Communication Link Mobile phones have been found to lose connection to the 6.
Page 478 476 MULTIMEDIA Voice Tree...
Page 479 MULTIMEDIA NOTE: 7. Storing Dial tones in contact names is possible but only the first number encountered in a contact name will be 1. You can replace “John Smith” with any name in your sent. For example, if there is a number stored in the mobile or favorite phone book.
Page 480 478 MULTIMEDIA NOTE: 2. You can replace “Mobile” with “Home,” “Work” or “Other.” 1. You can replace “John Smith” with any name in your mobile or favorite phone book. You can also say “Send 3. You can replace “Incoming Calls” with “Outgoing a message to John Smith”...
Page 481 MULTIMEDIA 5. You can replace “248 555 1212” with any phone number 7. If your phone does not support phonebook download or supported by your Mobile phone. call log download over Bluetooth then these commands will return a response that the contact does not exist in 6.
Page 482: General Information
480 MULTIMEDIA General Information not satisfactorily “clear” by the repositioning of the an- tenna, it is recommended that the radio volume be turned The following regulatory statement applies to all Radio down or off during mobile phone operation when not Frequency (RF) devices equipped in this vehicle: using Uconnect (if equipped).
Page 483 MULTIMEDIA environments, such as aboard airplanes. If you are unsure NOTE: of restrictions, you are encouraged to ask for authorization • This equipment has been tested and found to comply before turning on the wireless radio. with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 484: Voice Command (Uconnect 3/3 Nav)
482 MULTIMEDIA VOICE COMMAND (UCONNECT 3/3 NAV) WARNING! Uconnect 3/3 NAV Any voice commanded system should be used only in safe driving conditions following all applicable laws, The Uconnect Voice Command system allows including laws regarding phone use. Your attention you to control your AM, FM radio, satellite radio, should be focused on safely operating the vehicle.
Page 485 MULTIMEDIA Pushing the Uconnect Voice Command button while Natural Speech the system is speaking is known as “barging in.” The Natural speech allows the user to speak commands in system will be interrupted, and after the beep, you can say phrases or complete sentences.
Page 486: Uconnect Voice Commands
484 MULTIMEDIA Uconnect Voice Commands Starting Voice Recognition (VR) Session In Radio/Player Modes The Uconnect Voice Command system understands two types of commands. Universal commands are available at In this mode, you can say the following commands: all times. Local commands are available if the supported NOTE: The commands can be said on any screen when a radio mode is active.
Page 487 MULTIMEDIA Voice Tree...
Page 488 486 MULTIMEDIA • You can replace “rock” with any of the satellite music NOTE: types. • You can replace “950 AM” with any other AM or FM frequency, such as “98.7 FM.” • Available Voice Commands are shown in bold face and shaded grey.
Page 489 MULTIMEDIA NOTE: • VR commands, Albums, Artists, and Genre names are based on the music metadata contained on the loaded/ • You can replace the album, artist, song, genre, playlist, connected device. podcast and audio book names with any corresponding names on the current device that is playing.
Page 490 488 MULTIMEDIA...
Page 491 MULTIMEDIA NOTE: • You can also say “Show Current Weather” or “Show extended weather” or “Show five day forecast” or • You can replace “NFL” with any league shown on the “Show ski info” to get other forecasts. sports league screen. For example you can say “Show MLB headlines”...
Page 492 490 MULTIMEDIA • Navigation commands only work if equipped with NOTE: Navigation. • Only available with Navigation equipped vehicles. • Available Voice Commands are shown in bold face and • You can replace “Player” with “Radio,” “Navigation,” shaded grey. “Phone,” “Climate,” “More” or “Settings.”...
Page 493 MULTIMEDIA...
Page 494: Cd/Dvd Disc Maintenance
492 MULTIMEDIA NOTE: 3. Do not apply paper or tape to the disc; avoid scratching the disc. • You can also say “Find City,” “Find Favorite,” “Find Play by Category,” “Find Play by Name,” “Find Re- 4. Do not use solvents such as benzene, thinner, cleaners, cently Found,”...
Page 495 CUSTOMER ASSISTANCE CONTENTS SUGGESTIONS FOR OBTAINING SERVICE FOR ▫ Customer Assistance For The Hearing Or Speech YOUR VEHICLE ......494 Impaired (TDD/TTY) .
Page 496: Suggestions For Obtaining Service For Your Vehicle
494 CUSTOMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR IF YOU NEED ASSISTANCE YOUR VEHICLE The manufacturer and its authorized dealer are vitally interested in your satisfaction. We want you to be happy Prepare For The Appointment with our products and services. If you are having warranty work done, be sure to have the right papers with you.
Page 497: Fca Us Llc Customer Center
CUSTOMER ASSISTANCE 495 Any communication to the manufacturer’s customer center Mexico, D. F. should include the following information: In Mexico City: 5081-7568 • Owner’s name and address Outside Mexico City: 1-800-505-1300 • Owner’s telephone number (home and office) Puerto Rico And U.S. Virgin Islands •...
Page 498: Service Contract
496 CUSTOMER ASSISTANCE Canadian residents with hearing difficulties that require Limited Warranty expires, please refer to the contract assistance can use the special needs relay service offered by documents, and contact the person listed in those docu- Bell Canada. For TTY teletypewriter users, dial 711 and for ments.
Page 499: Warranty Information
CUSTOMER ASSISTANCE 497 WARRANTY INFORMATION a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved See the Warranty Information Booklet for the terms and in individual problems between you, your authorized provisions of FCA US LLC warranties applicable to this dealer or FCA US LLC.
Page 500: Publication Order Forms
498 CUSTOMER ASSISTANCE PUBLICATION ORDER FORMS Owner’s Manuals To order the following manuals, you may use either the These Owner’s Manuals have been prepared with the website or the phone numbers listed below. Visa, Master- assistance of service and engineering specialists to acquaint card, American Express, and Discover orders are accepted.
Page 501 INDEX...
Page 502 500 INDEX About Your Brakes ..... .237, 372 Air Conditioning Filter..... . .100 Adding Engine Coolant (Antifreeze) .
Page 503 INDEX 501 Adding Fluid ....338, 339, 340, 384 Brake Assist System ......162 Fluid And Filter Changes .
Page 504 502 INDEX Cargo Load Floor ......110 Seating Positions ......211 Cargo Management System .
Page 505 INDEX 503 Pressure Cap ......334 Door Opener, Garage ......114 Radiator Cap .
Page 506 504 INDEX Air Cleaner ......324 Exhaust Gas Caution .....226, 378 Block Heater .
Page 507 INDEX 505 Fluid Leaks.......229 Fueling........261 Fluid Level Checks Fuses .
Page 508 506 INDEX Lights On Reminder ..... . .66 Intermittent Wipers (Delay Wipers)....70 On With Wipers .
Page 509 INDEX 507 Latches........229 Headlight Switch ......64 Hood .
Page 510 508 INDEX Load Shed Methanol ....... .376 Battery Saver Mode ..... . .143 Mini-Trip Computer.
Page 511 INDEX 509 Checking ......320 ParkSense System, Rear ..... .253 Dipstick .
Page 512 510 INDEX Pregnant Women And Seat Belts ....185 Release, Hood ......107 Preparation For Jacking .
Page 513 INDEX 511 Safety Defects, Reporting .....497 Rear Seat ......179 Safety, Exhaust Gas .
Page 514 512 INDEX Service Manuals ......498 Power ......248, 249 Shift Lever Override .
Page 515 INDEX 513 Chains ....... .361 To Open Hood ......107 Changing .
Page 516 514 INDEX Transporting Pets ......225 Connect Or Disconnect Link Between The Uconnect Tread Wear Indicators ..... . .354 Phone And Mobile Phone .
Page 517 INDEX 515 Vanity Mirrors ......63 Power ....... .102 Vehicle Certification Label .
Page 518 INSTALLATION OF RADIO TRANSMITTING The antenna cable should be as short as practical and EQUIPMENT routed away from the vehicle wiring when possible. Use Special design considerations are incorporated into this only fully shielded coaxial cable. vehicle’s electronic system to provide immunity to radio Carefully match the antenna and cable to the radio to frequency signals.

Dodge Journey 2018 Owner's Manual

Introduction

Graphical

Getting to Know Your Vehicle

Getting to Know Your Instrument Panel

Safety

Starting and Operating

In Case of Emergency

Servicing and Maintenance

Technical Specifications

Quick Links

Chapters

Related Manuals for Dodge Journey 2018

Summary of Contents for Dodge Journey 2018