Subscribe to Our Youtube Channel
Related Manuals for Garz & Fricke SANTOKA Series
Summary of Contents for Garz & Fricke SANTOKA Series
- Page 1 SANTOKA 10.1" Boxed PCT IPS V1.2 Manual For PCB revision 0.7 or for HW 1.1 or later...
-
Page 2: Table Of Contents
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual Content Introduction Safety Hints Product Introduction Product introduction Type plate and device information Product names and variants Related documents and online support Product Description Technical data PCB design and Pin assembly Installation and start up Connection Scheme External interfaces and Schematics SMA-Connector (X115) -
Page 3: Introduction
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual 1 Introduction Thank you very much for purchasing a Garz & Fricke product. Our products are dedicated to professional use and therefore we suppose extended technical knowledge and practice in working with such products. The information in this manual is subject to technical changes, particularly as a result of continuous product upgrades. -
Page 4: Safety Hints
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual 2 Safety Hints Please read this section carefully and observe the instructions for your own safety and correct use of the device. Observe the warnings and instructions on the device and in the manual. Garz & Fricke embedded systems have been built and tested by us and left the company in a perfectly safe condition. - Page 5 SANTOKA 10.1" Boxed PCT IPS V1.2 Manual To comply with FCC and Industry Canada RF exposure limits for general population / uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures Note: This equipment has been tested and found to comply with the limits for a...
-
Page 6: Product Introduction
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual 3 Product Introduction This document is applicable for hardware revisions 1.1 or later of the SANTOKA SERIES. Please find the hardware version grid in Annex A: Product introduction SANTOKA is an Embedded System to be used as human machine interface (HMI) in various applications. -
Page 7: Related Documents And Online Support
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual <additional description> contains variants which are important to sales product description, i.e. without or with WLAN/Bluetooth module (“W/B”) untreated glass surface or including antiglare treatment (“AG”) front frame made from die-cast zinc or aluminium (“Alu”) different memory capacities for RAM and/or eMMC customer-specific reduced assembly etc. -
Page 8: Product Description
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual 4 Product Description This drawing is meant for your orientation. For drawing please refer to Annex B: You will get 3 D model (CAD) Drawings after signed a NDA contract. Die-cast zinc or aluminium frame Front Cover... -
Page 9: Technical Data
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual Technical data Singlecore M Singlecore Dualcore lite Dualcore Quadcore Type NXP i.MX6S NXP i.MX6DL NXP i.MX6D NXP i.MX6Q Cores Frequency 800 MHz 1 GHz per core NEON for SIMD media acceleration and VFP operations L1 cache, 32 KB for instruction, 32 KB for data 512 KB L2 cache (Singlecore and Dualcore lite) Features... - Page 10 SANTOKA 10.1" Boxed PCT IPS V1.2 Manual LCD Display Singlecore M Singlecore Dualcore lite Dualcore Quad Size [inch/mm] 10.1 / 256.0 Display Technology TFT IPS Width x Height [pixel] 1280 x 800 Colors [bit] 24 (16.7 M colors) Backlight Unit Luminance [cd/m²] 500 (Typ.)
- Page 11 SANTOKA 10.1" Boxed PCT IPS V1.2 Manual Lifetime Backlight Lifetime 50,000 Display [h] MTBF ≥ 50,000 Backlight lifetime is dictated by the LCD manufacture´s specification. Backlight lifetime is the approximate time at which the brightness decreases to half of its original brightness. Reduction of brightness due to backlight lifetime is not considered as failure.
-
Page 12: Pcb Design And Pin Assembly
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual PCB design and Pin assembly As this manual describes a boxed version, only the external interfaces will be mentioned in the following chapter. 1a 1b (Exemplary illustration: The illustration shows the fully equipped SANTOKA Dualcore. It shows no heatsink to provide a better overview.) Pos. -
Page 13: Installation And Start Up
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual 5 Installation and start up The content of this document is limited to explain the device connectors and how to access SANTOKA via FTP over your local area network (LAN) within a few seconds. For advanced hardware specifications and software support, please refer to chapter 3.4 Related documents and online support Product... -
Page 14: External Interfaces And Schematics
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual 6 External interfaces and Schematics SMA-Connector (X115) Name Description Information Signal Wi-Fi is certified only with the delivered antenna. For further information please contact Garz & Fricke GmbH. Ethernet (X117.1/X117.2) X117.1 Name Description Information Rx/Tx might be swapped (Auto-MDIX) -
Page 15: Power (X1)
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual Power (X1) Name Description Level DC Ground Nom. 24V ± 15% Vcc_In DC Input voltage Max. 14 ̴ 32 Header: Molex 43045-0200 Micro-Fit 2p Plug: Molex 43025-0200 Micro-Fit 2p, crimp contact Molex 43030-0007 Shielding with 6,3 mm male spade terminal connector Pin 1 (GND) is connected to frame/housing. -
Page 16: Can/Rs-485 Interface (X39)
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual CAN/RS-485 Interface (X39) Name Description Level GND_CAN_RS485 Ground for CAN and RS485 group To enable CAN1-Termination, bridge CAN1_TERM with CAN1_H CAN1_H CAN bus 1 high -24c+24 V CAN1_L CAN bus 1 low -24c+24 V To enable CAN1-Termination, bridge CAN1_TERM with CAN1_L... -
Page 17: Rs-232/Mdb (X13)
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual RS-232/MDB (X13) RS-232/RS-232 Name Description Level Ground RS232_TXD1 Port#1: Transmit data (Output) RS232_RXD1 Port#1: Receive data (Input) RS232_RTS1 Port#1: Request-to-send (Output) RS232_CTS1 Port#1: Clear-to-send (Input) Ground RS232_TXD2 Port#2: Transmit data (Output) RS232_RXD2 Port#2: Receive data (Input) RS232_RTS2 Port#2: Request-to-send (Output) RS232_CTS2... -
Page 18: Usb - Host (X34)
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual USB - Host (X34) Name Description Level USB_H1_VBUS Power supply +5 V DC max 500mA USB_H1_DN Data minus (D-) USB_H1_DP Data plus (D+) Ground Header: USB Type A USB - Host (X113) Name Description Level USB_H1_VBUS... -
Page 19: Hdmi (X111)
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual 6.11 HDMI (X111) Name Description Level TMDS Data2+ TMDS Data2 shield TMDS Data2– TMDS Data1+ TMDS Data1 shield TMDS Data1– TMDS Data0+ TMDS Data0 shield TMDS Data0– TMDS Clock+ TMDS Clock Schirm TMDS Clock– Utility I2C_CLK SCL (I²C serial clock for DDC) -
Page 20: Battery-Holder (X121)
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual 6.12 Battery-Holder (X121) Name Description Level Supply Ground Header: AUK BH19VWG-R5H-H Battery: CR1220... -
Page 21: Document Revision History
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual 7 Document revision history The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. Author Description Revision... -
Page 22: Technical Support
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual 8 Technical support Before contacting the Garz & Fricke support team, please try to help yourself by the means of this manual or any other documentation provided by Garz & Fricke or the related websites. If this does not help at all, please feel free to contact us. - Page 23 SANTOKA 10.1" Boxed PCT IPS V1.2 Manual Technical Appendix For PCB revision 0.7 or for HW 1.1 or...
-
Page 24: Annex A: Hardware Revision Information
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual Annex A: Hardware revision information This document is applicable for all products listed below. Please note that customized variants might possibly not support all features listed herein. Additional features are documented in specific attachments. Article Number Marking on PCB Platform... -
Page 25: Annex B: Mechanical Specifications
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual Annex B: Mechanical specifications B-1 Mechanical Drawings... -
Page 26: Annex C: Quality And Incoming Inspections
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual Annex C: Quality and Incoming Inspections C-1 Display and Touch Maximum Maximum amount Specification amount Notes display other area area Bright Dot Minimum One dot = one sub- Electrical distance pixel defects L ≥ 5mm Dark Dot between One pixel consists... -
Page 27: Evaluation Criteria Of Standard Display Module
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual C-2 Evaluation criteria of standard display module Evaluated Zone 1: Areas in the immediate viewing area: dirt and dust enclosures / stains / striae / scratches from max. 500 µm (diameter) or 0.02 mm2 (surface), 5 pcs. per dm permitted, but no clustering. -
Page 28: Annex D: Battery
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual Annex D: Battery D-1 Battery Specifications The internal baseboard is equipped with a Lithium battery (CMOS battery, type CR1220), which has a typical lifetime longer than 8 years. Typically we assemble one of the following batteries: Manufacturer Model Article Number... -
Page 29: Replacement Of The Internal Battery
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual D-2 Replacement of the internal battery The internal battery is placed as per figure below. For replacement, the SD-card and the back cover have to be removed. The device shall be opened by authorized and skilled personnel only. Danger of electric hazard! First before opening, please make sure that the unit is completely disconnected from any power supply, direct or indirect. -
Page 30: Annex E: Guidelines And Standards
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual Annex E: Guidelines and Standards E-1 RoHS Declaration Devices comply with the requirements of Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. -
Page 31: Annex F: Common Documentation
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual Annex F: Common documentation F-1 Warranty hints Garz & Fricke embedded systems are subject to manufacturer’s guarantee as long as the products are handled with adequate care and caution and in accordance to this manual. The period of guarantee starts from the date of shipment The products are warranted against defects in material, quality and functionality within the guaranteed period. -
Page 32: Application Notes
SANTOKA 10.1" Boxed PCT IPS V1.2 Manual F-2 Application notes The products covered by this document are designed and manufactured for the following applications (I). If you intend to use these products in applications as quoted in (II) or (III) we highly recommend a personal contact with our consultants and/or technical sales team.
Need help?
Do you have a question about the SANTOKA Series and is the answer not in the manual?
Questions and answers