Evak DPC-10 Installation And Operation Manual
  1. Manuals
  2. Brands
  3. Evak Manuals
  4. Controller
  5. DPC-10
  6. Installation and operation manual

Evak DPC-10 Installation And Operation Manual

Water pump digital pressure
Hide thumbs Also See for DPC-10:

Advertisement

Table of Contents

See also: Operating Manual
www.evak-pumps.com
DPC-10
Water Pump Digital Pressure Controller
Installation and Operation Manual
EVAK PU M P TEC HNOL OGY C OR P.
No. 551, Zhongshan Rd., Qingshui Dist., Taichung City 436, Taiwan.
TEL: +886-426-233556 Fax: +886-426-235559
Vol.PMDPC-15051-1.2-R

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DPC-10 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Evak DPC-10

Summary of Contents for Evak DPC-10

  • Page 1 DPC-10 Water Pump Digital Pressure Controller Installation and Operation Manual EVAK PU M P TEC HNOL OGY C OR P. No. 551, Zhongshan Rd., Qingshui Dist., Taichung City 436, Taiwan. TEL: +886-426-233556 Fax: +886-426-235559 Vol.PMDPC-15051-1.2-R...

  • Page 2: Ec Declaration Of Conformity

    General Manager 220V, but if connect to contactor in the control Place : Taichung City, Taiwan panel then DPC-10 controller can fit the pump over 2HP. EVAK PUMP TECHNOLOGY CORP. No.551, Zhongshan Rd., Qingshui Dist., Taichung City 436, Taiwan (R.O.C.)

  • Page 3: Wiring Diagram

    L,N: Power Supply 3 phase PUMP W1,U1: Motor Wire (MCCB) Blue,Brown: Controller Power Supply If installing DPC-10 with a varistor, please connect varistor wire in parralled with Yellow,White: Controller Relay Brown Blue thin Brown and Blue wires of the DPC-10.
  • Page 4 5.The status of LED lights “ ” (Short press once to enter Basic Setting Mode) Item Light Message indication Pump status Setting procedure : Max. pressure → Min. start pressure → Time-Delay Control loop off from the system Pump off Data Item Parameters Display Default...
  • Page 5 “ ” long press for 3 seconds (Advanced setting Mode) Display Default Data Display Default Data Item Parameters Description Item Parameters Description Range Range Code Unit Code Unit a.Select to modify automatic re-start time, a.Select to switch the Unit of working press the left or right button to adjust the pressure, press the right button to change value, after finish the setting,press the SET...
  • Page 6 9.The actual operating parameters display Item Parameters Display Default Data Description Range Code Unit a.Select to restore default value settings a. Press once to browse original pressure value (dF-y), press the right button and adjust the parameter value from dF-n to dF-y. 1).Max.
  • Page 7 3).Pressure of water shortage setting display (Dry running) b. Press once to enter basic setting (Show code P-Dry) 1).Max. pressure setting (high pressure) (Show code P-max) Press to adjust the value upward Press to adjust the value downward ↓ Press again ↓...
  • Page 8 3).Time-Delay setting after reaching the Max. Pressure 5).After finishing above setting, 3 seconds later will go to the actual (Show code pressure status display automatically. Delay) Press to adjust the value upward Press to adjust the value downward ↓ Press once c.
  • Page 9 2).Detection time setting of water shortage 4).Time setting of automatic re-start running after warning shutdown (Show code P-Dry & sec) (Dry running or Over pressure) (α value) (Show code Auto reset) Press Press to adjust the value upward to adjust the value upward Press Press to adjust the value downward...

  • Page 10: Fault Display

    10.Fault Display 6).Restore to default value setting or not » Restore to default value settings (show code dF-y) a).EEEE Pressure controller display “EEEE” It means the failure of pressure sensor. b).FFFF Press to adjust the value to dF-y Press once and restore to default value (Show code ----) Pressure controller display “FFFF”...

Table of Contents

Save PDF