Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Jovision JVS-H210
Summary of Contents for Jovision JVS-H210
-
Page 1: User Manual
User Manual ... - Page 2 CHANGE THE DEFAULT PASSWORD Default Network Camera Account : Username: abc Password: 123 The default password (123) for the abc account is for first‐time log‐in purposes only. You should change this default password to better protect against security risks, such as the unauthorized access by others to the product that may prevent the product from functioning properly and/or lead to other undesirable consequences. For your privacy, we strongly recommend changing the password to something of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end‐user. FCC Certification Requirements Caution: Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. ...
-
Page 3: Table Of Contents
Contents Introduction ............................3 1.1 Appearance and Interface ....................3 1.2 Specification ........................3 Installation............................4 2.1 Ceiling Mounting .........................4 Network Connection .........................5 3.1 Wireless connection......................5 3.2 Wired Connection* ......................5 Preparation on Smart Phone (iOS, Android) ..................6 4.1 Get CloudSEE APP........................6 4.2 Register CloudSEE Account....................6 4.3 Power‐on the Device ......................6 Add JVS‐H210 on Smart Phone (iOS, Android)..................7 5.1 How to Choose Device Adding Methods................7 5.2 Add by Sound Wave ......................7 5.3 Add Wi‐Fi Device on iPhone....................9 5.4 Add Wi‐Fi Device on Android....................12 5.5 Add by CloudSEE ID ......................13 5.6 Scan devices in LAN......................14 2 ... -
Page 4: Introduction
Introduction 1.1 Appearance and Interface No. Name Description 1 Photo‐resistance Light‐controlled variable resistor, control IR cut filter switch 2 Lens Optical imaging element 3 MIC Microphone 4 TF Card Slot Maximum: 64GB 5 Speaker Audio out 6 Network Ethernet cable line in. Interface 7 Reset 1. Press 3 seconds to start soundwave configuration 2. Press 15 seconds to restet the device. 8 Power Light Indicates the power is on. 9 Network Light 1.If hasn’t been configured, green light will blink equelly. 2. If has been configured, grenn light will blink with one long and one short. 10* Power DC 5V ... -
Page 5: Installation
2 Installation 2.1 Ceiling Mounting Before you start: JVS‐H210 can be installed to wall/ceiling or fixed on desktop. Ceiling mounting is taken as an example in this section; if you adopt wall mounting, you can also take below procedure as a reference. Steps: 1. Attach the mounting (bottom base of the JVS‐H210 which can be removed) to the ceiling and tighten the screws to fix it. 2. Rotate the base to secure it to the bottom base, and secure JVS‐H210 camera on the mounting base. Notes: Please make sure that the ceiling can support more than 50(N) Newton gravities if the camera is fixed to the ceiling. 4 ... -
Page 6: Network Connection
3 Network Connection 3.1 Wireless connection Notes: With wireless connection, you can add the device by “Add Wi‐Fi Device”, which is based on AP function. Once you connect JVS‐H210 to the router with Ethernet cable, JVS‐H210 will disable AP, which means the function mentioned above won’t work. 3.2 Wired Connection* Notes: “Add Wi‐Fi Device” does not apply to wired connection. For JVS‐H210 only 5 ... -
Page 7: Preparation On Smart Phone (Ios, Android)
4 Preparation on Smart Phone (iOS, Android) 4.1 Get CloudSEE APP 1. Search “CloudSEE” in App Store (iOS) or Google play (Android). 2. Get and install CloudSEE on your smart phone. 4.2 Register CloudSEE Account Notes: You need to register a CloudSEE account before using CloudSEE service which is free. Although you can use “Visitor Login”, but we strongly recommend that register your own account for better experience. With CloudSEE service account, devices list will automatically upload and store ... -
Page 8: Add Jvs-H210 On Smart Phone (Ios, Android)
5 Add JVS‐H210 on Smart Phone (iOS, Android) Before you start: The device has to be configured by “Add by Sound Wave” or “Add Wi‐Fi Device” for first‐time use if you want to use wireless connection. Press reset button for about 3 seconds and release to start sound wave configuration Press reset button for about 15 seconds and release to reset the device. 5.1 How to Choose Device Adding Methods Methods Situation Connection The device had been connect to Internet Add by CloudSEE ID Wireless, Ethernet Cable and get CloudSEE ID online. The device had been connect to Internet Scan QR Code and get CloudSEE ID online.(The same as Wireless, Ethernet Cable “Add by CloudSEE ID”) First‐time use or the device has been Add Wi‐Fi Device Wireless reset. The device has been connected to the Scan Devices in LAN Wireless, Ethernet Cable same network as your smart phone. First‐time use or the device has been Add by sound wave Wireless reset. 5.2 Add by Sound Wave Notes: Set the volume of your phone to maximum level before this operation. Make sure there is no noise when add the device by sound wave. ... - Page 9 ① ② Tap , and select “Add by sound wave” Select the network which your phone joined, input the password and tap Next. ③ ④ Press reset button for at least 3 seconds until There will be a demonstration with audio hear the voice “Start voice configuration”, instructions on how to use this function. then release the button and tap Next Then close the demonstration. 8 ...
-
Page 10: Add Wi-Fi Device On Iphone
⑤ ⑥ Keep the speaker of your phone close enough Then CloudSEE starts scanning devices in the to the MIC of JVS‐H210, click the sound wave network. Choose the one you want to add, icon to send sound wave, you can send it for and click Add many times until hear the voice “Receive network configuration”, which means the device has joined the network. ⑦ ⑧ The device will be added. Tap the device on the list, live video will display. 5.3 Add Wi‐Fi Device on iPhone Notes: Do not connect Ethernet cable before this operation. 9 ... - Page 11 ① ② Power‐on the device, wait for about 40 Open CloudSEE App, Tap , and select seconds, JVS‐H210 will create an AP, choose “Add Wi‐Fi Device”. this AP (IPC‐H‐XXXXXXX) from the WLAN settings of your iPhone, and enter the password (12345678) when prompted. ③ ④ CloudSEE will prompt that a new device has Then the live video of the device will display, been found. Tap NEXT. you can access Audio, PTZ, Talk function here, but we haven’t finished configuring ...
- Page 12 ⑤ ⑥ Select the Wi‐Fi network for JVS‐H210 and When the Wi‐Fi connection is completed, input the password, tap Configure. After Open CloudSEE App again. hearing success from the device, you NEED to close the app and switch Wi‐Fi network of your iPhone to the one which JVS‐H210 is connected. ⑦ ⑧ Confirm the information of the device, and CloudSEE will prompt that “A new device has tap Save been configured by you”, tap Add. 11 ...
-
Page 13: Add Wi-Fi Device On Android
⑨ ⑩ The device will be added. Tap the device on the list, live video will display. 5.4 Add Wi‐Fi Device on Android ① ② Open CloudSEE App, Tap , and select “Add The app will scan AP from JVS‐H210 and list Wi‐Fi Device”. them, select the one you want to add. You can check whether it is the one in next step, or go back to this page to choose another. 12 ... -
Page 14: Add By Cloudsee Id
③ ④ Then the live video of the device will display, Select the Wi‐Fi network for JVS‐H210 and check the picture and confirm you can also input the password, tap Configure. access PTZ, Two‐way Talk function here, but we haven’t finished configuring yet, Tap NEXT. ⑤ ⑥ Then CloudSEE will prompt that “Discovering Tap the device on the list, live video will Device”, and click Add display. 5.5 Add by CloudSEE ID Notes: This method requires that the device be connected to Internet and get CloudSEE ID online first. 13 ... -
Page 15: Scan Devices In Lan
① ② Open CloudSEE App, Tap , and select “Add Input CloudSEE ID, Username, Password of by CloudSEE ID”. the device, tap Save ③ ④ The device will be added. Tap the device on the list, live video will display. 5.6 Scan devices in LAN Notes: This method requires that the device be connected to the SAME Wi‐Fi network with your smart phone first. ... - Page 16 ① ② Then CloudSEE will detect devices in the Open CloudSEE App, Tap , and select “Scan LAN, choose the device(s) and tap Add. devices in LAN”. ③ ④ Tap the device on the list, live video will The device will be added. display. 15 ...