Subscribe to Our Youtube Channel
Related Manuals for Dynamic DX-RJM-HD
Summary of Contents for Dynamic DX-RJM-HD
- Page 1 DX-RJM-HD Heavy Duty Switch Joystick DX-RJM-HD Installation Manual GBK59690 Issue 5 July 2015...
- Page 2 [Page left blank intentionally]...
-
Page 3: About This Manual
Installation Manual Issue 5 1 About this manual This manual can help you understand and install the Dynamic Controls DX Heavy Duty Switch Joystick (DX-RJM-HD) Secondary Remote. It describes the general principles, but it gives no guidelines for specific applications. If there is a specific requirement for your application, please contact Dynamic Controls or one of the sales and service agents to assist you. - Page 4 GBK59690 DX Heavy Duty Switch Joystick Installation Manual Issue 5 Dynamic Controls owns and will retain all trademark rights. Dynamic Controls or its licensors own and will retain all copyright, trade secret and other proprietary rights, in and to the documentation.
-
Page 5: Table Of Contents
GBK59690 DX Heavy Duty Switch Joystick Installation Manual Issue 5 2 Contents 1 About this manual 2 Contents 3 Introduction to the DX Heavy Duty Joystick 4 Installation 4.1 Mount 4.2 Connect 4.3 Program 4.4 Test 5 Appendices 5.1 Intended use and regulatory statement 5.2 Maintenance 5.3 Warranty 5.4 Safety and misuse warnings... - Page 6 GBK59690 DX Heavy Duty Switch Joystick Installation Manual Issue 5 [Page left blank intentionally] Page 4...
-
Page 7: Introduction To The Dx Heavy Duty Joystick
Manual will be referred to as DSM throughout the rest of this manual. Note: The DX-RJM-HD is part of the DX System. Read the DX System Manual (DSM) before reading this manual. The DX-RJM-HD has eight switched driving directions as shown... - Page 8 GBK59690 DX Heavy Duty Switch Joystick Installation Manual Issue 5 [Page left blank intentionally] Page 6...
-
Page 9: Installation
Avoid positions that are exposed to splashing and other forms of abuse. There is a drainage hole at the bottom of the DX-RJM-HD. Do not mount the DX-RJM-HD so that the drainage hole is blocked. Figure 2: Measurements at the bottom of the case Note that the top of the case is narrower than the bottom. -
Page 10: Connect
HD indoors and out of contact with water and other liquids. 4.2 Connect The DX-RJM-HD is a DX Secondary Remote. It must be installed in a DX System that already has a DX Power Module and a DX Master Remote. -
Page 11: Program
As a general guideline select RJM for Drive Profile 1, 2 and 3, and Master for Drive Profile 4 and 5. This will activate use of the DX-RJM-HD in the first three Drive Profiles, and the Master Remote (usually joystick operation) in Drive Profile 4 and 5. Drive Profile 4 and 5 can then be used either by an attendant, or as an alternative control for the user. - Page 12 GBK59690 DX Heavy Duty Switch Joystick Installation Manual Issue 5 [Page left blank intentionally] Page 10...
-
Page 13: Appendices
The DX-RJM-HD is a DX Secondary Remote, utilising a robust switched joystick, intended for powered wheelchair users who could damage a standard joystick. The DX-RJM-HD is a module of the DX System, intended to allow users interaction with the DX System. -
Page 14: Warranty
5.4 Safety and misuse warnings The DX-RJM-HD is a module of the DX System and therefore all safety and misuse warnings that appear in the DSM apply to the DX-RJM-HD as well. See DSM section 10.4. -
Page 15: Electromagnetic Compatibility (Emc)
2.1.1 of the DX System Manual. 5.6 Environmental statement Dynamic Controls confirms that the product variants specified in this manual, as sub-assemblies of electronic and electrical equipment supplied for further integration by a medical device manufacturer, conform to applicable requirements of Directive 2011/65/EU, recast of Directive 2002/95/EC - Restriction of the use of certain Hazardous Substances in electrical and electronic equipment. - Page 16 GBK59690 DX Heavy Duty Switch Joystick Installation Manual Issue 5 [Page left blank intentionally] Page 14...
- Page 17 GBK59690 DX Heavy Duty Switch Joystick Installation Manual Issue 5 [Page left blank intentionally] Page 15...
- Page 18 Dynamic Controls was established in 1972 and is headquartered in New Zealand. Regional centres are located in Europe, United States, Asia, and Australasia. ISO 13485 certified – Dynamic Controls goes above and beyond industry standard expectations to ensure customers receive the best products possible. www.dynamiccontrols.com...
Need help?
Do you have a question about the DX-RJM-HD and is the answer not in the manual?
Questions and answers