Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Massive Audio BP200.2
Summary of Contents for Massive Audio BP200.2
- Page 1 BLADE(BP) Series Amplifiers...
- Page 2 BLADE(BP) BLADE(BP)
- Page 3 1 Ohm Stable Design (Mono Amps-BP1200.1, BP2000.1) 2 Ohm Stable Design (Full Range Mono Amps-BP600.1, BP1000.1, BP4000.1, BP6000.1)
- Page 4 is 9V to 200mv(250mV). This is NOT a volume control!
- Page 5 16. NO Indicator Indicator the amplifier is grounded, and receiving +12V and REM power. 17. CLIP Indicator(BP4000.1,BP6000.1) This LED indicates when clipping is present while playing source material. If the CLIP LED is flashing it also indicates the clip limiter is engaging. At this point it is suggested to adjust the amplifiers gain level until the CLIP LED is only flashing on peak bass notes.
- Page 6 Fig 1. 2-ch amplifier panel layout BP500.2/BP1000.2/BP1500.2 Fig 2. Mono amplifier panel layout BP600.1/BP1000.1...
- Page 7 Fig 2. Mono amplifier panel layout BP1200.1/BP2000.1 BP4000.1/BP6000.1 2 MINIMUM BANDPASS BASS BOOST FREQ LEVEL REMOTE GAIN 0DB 12DB 0.25V 50Hz 16KHz 750Hz...
- Page 8 Fig 3. 4-CH amplifier panel layout BP800.4/BP1000.4 Fig 4. 5-ch amplifier panel layout BP1500.5...
- Page 9 Fig 5. Mono amplifier Wiring BP600.1/BP1000.1 2 OHM MINIMUM BP1200.1/BP2000.1 1 OHM MINIMUM...
- Page 10 Fig 6. Mono Amplifier Wiring BP600.1/BP1000.1 4 OHM MINIMUM BP1200.1/BP2000.1 2 OHM MINIMUM *Subwoofer loads cannot be less than the minimum stable impedance rated in this manual. The two negative and positive speaker terminanls are wired internally. Only one neagative and one positive terminalis required when wiring to bp mono amplifiers.
- Page 11 Fig 7. Mono amplifier Wiring BP4000.1/BP6000.1 2 MINIMUM BANDPASS BASS BOOST FREQ LEVEL REMOTE GAIN 50Hz 16KHz 0DB 12DB 750Hz 0.25V 2 OHM MINIMUM...
- Page 12 Fig 8. BP500.2/1000.2/1500.2 Amplifier Wiring (1-CHANNEL MODE) 4 OHM Fig 9. BP500.2/1000.2/1500.2 Amplifier Wiring (2-CHANNEL MODE) 4 OHM 4 OHM...
- Page 13 Fig 10. BP800.4/1000.4 Amplifier Wiring (3-CHANNEL MODE) 2OHM-4 OHM 2OHM-4 OHM Fig 11. BP800.4/1000.4 Amplifier Wiring (4-CHANNEL MODE) 2OHM-4 OHM 2OHM-4 OHM 2OHM-4 OHM 2OHM-4 OHM...
- Page 14 Fig 12. BP1500.5 Amplifier Wiring (4-CHANNEL MODE) 2OHM-4 OHM 2OHM-4 OHM 2OHM-4 OHM 2OHM-4 OHM 2OHM-4 OHM 2OHM-4 OHM 4 OHM TO 8OHM 4 OHM TO 8OHM...
Need help?
Do you have a question about the BP200.2 and is the answer not in the manual?
Questions and answers