Download Print this page

Haier AW09ES2VH series Installation Manual

Ductless split air conditioner.
Hide thumbs
   

Advertisement

Installation M anual
Step 1 - Preparation ...................................................................................................................... 2
Step 2 - Installation of the Indoor Unit ........................................................................................... 3
Step 3 - Installation of the Out door Unit........................................................................................ 4
Step 4 - Interconnecting the Indoor and Outdoor Units ................................................................. 5
S
e t>
p
5
-
L
e
k a>
T
e
t s>
a
Step 6 - Char ging ...........................................................................................................................7
Section 7 - Explaining Operation to the End User ........................................................................... 8
eacoast Application ................................................................................................... 8
0010586612
n
d
E
u c>
t a>
o i>
n
. . .
. . .
. . .
.................................................................................................. 8
Ductless S plit Air Conditioner
Indoor
AW09ES2VH*
AW12ES2VH*
AW18ES2VH*
AW24ES2VH*
AW09TE1VH*
AW12TE1VH*
AW18TE2VH*
AW24TE2VH*

Table of Contents

. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
Outdoor
1U09ES2VHA
1U12ES2VHA
1U18ES2VHA
1U24ES2VHA
1U09TE1VHA
1U12TE1VHA
1U18TE2VHA
1U24TE2VHA
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
.....6

Advertisement

   Related Manuals for Haier AW09ES2VH series

   Summary of Contents for Haier AW09ES2VH series

  • Page 1: Table Of Contents

    Ductless S plit Air Conditioner Installation M anual Indoor Outdoor AW09ES2VH* 1U09ES2VHA AW12ES2VH* 1U12ES2VHA AW18ES2VH* 1U18ES2VHA AW24ES2VH* 1U24ES2VHA AW09TE1VH* 1U09TE1VHA AW12TE1VH* 1U12TE1VHA AW18TE2VH* 1U18TE2VHA AW24TE2VH* 1U24TE2VHA Table of Contents Step 1 - Preparation ........................2 Step 2 - Installation of the Indoor Unit ................... 3 Step 3 - Installation of the Out door Unit..................

  • Page 2: Step 1 - Preparation

    Step 1 - Preparation Required Tools for Installation Procedure for Selecting the Location Note: detector place. Clearances of Indoor and Outdoor Units The models adopt HFC free refrigerant R410A Attention must be paid to more than 4in. the pitch of drain hose Floor xing dimensions of the outdoor unit (Unit: inch) more than...

  • Page 3: Step 2 - Installation Of The Indoor Unit

    Step 2 - Installation of the Indoor Unit Attaching the Mounting Plate to the Wall Step 2.1 Using a stud sensor, locate and mark the stud positions in the wall where the indoor unit is to be mounted. Step 2.2 Place the mounting plate on the wall in the desired location taking into account the minimum clearances necessary for Step 2.1...

  • Page 4: Step 3 - Installation Of The Outdoor Unit

    Mounting the Indoor Unit Onto the Wall Plate Step 2.9 With the top of the indoor unit closer to the wall, hang the indoor unit on the upper hooks of the mounting plate. Slide the unit slightly side to side to verify proper placement of the indoor unit on the mounting plate.

  • Page 5: Step 4 - Interconnecting The Indoor And Outdoor Units

    Step - 3.3 Connect the wiring for both the power source and indoor wiring. Wire the system according to applicable national / local codes. Verify that the wiring connections for the indoor unit match wire for wire. Step 3.3 Step 3.4 (1-1, 2-2, 3-3, Gnd-Gnd).

  • Page 6

    Step 5 - Leak Test and Evacuation Leak Test +D]DUG RI ([SORVLRQ 1HYHU XVH DQ RSHQ DPH WR GHWHFW JDV leaks. Explosive conditions may occur. Use a leak test solution or other approved methods for leak testing. Failure to follow recommended safe leak test procedures could result In death RU VHULRXV LQMXU\ RU HTXLSPHQW RU SURSHUW\ GDPDJH Use only dry nitrogen with a pressure regulator for...

  • Page 7: Step 6 - Charging

    piping hole. Use a sealant to seal the piping hole opening to prevent weather elements from entering the building. (Illustration 6) Less than Verify the condensate drain line has a constant pitch It becomes The end is imm- There is the bad It waves.

  • Page 8: Section 7 - Explaining Operation To The End User

    Section 7 - Explaining Operation t o the End User operation, etc.) ATING INS TRUC TIONS carefully . Model Name Outdoor 1U09ES2VHA 1U12E S2VHA 1U18ES2VHA 1U24ES2VHA AW09ES2VH* Indoor AW24ES2VH* AW12ES2VH* AW18ES2VH* Cooling °F(°C) 14~115(-10~46) 14~115(-10~46) 14~115(-10~46) 14~115(-10~46) Operating Range Heating °F(°C) -4-75(-20-24) -4-75(-20-24) -4-75(-20-24)

  • Page 9

    [This page intentionally left blank.]...

  • Page 10

    Model #: 1U09ES2VHA, 1U12ES2VHA 1U18ES2VHA, 1U24ES2VHA AW09ES2VH*, AW12ES2VH* AW18ES2VH*, AW24ES2VH* AW09TE1VH*,1U09TE1VHA AW12TE1VH*,1U12TE1VHA AW18TE2VH*,1U18TE2VHA Haier America, AW24TE2VH*,1U24TE2VHA Wayne, NJ 07470 ©2017 Haier America Trading, LLC. Issued Date: Jan 2017 Update...

Comments to this Manuals

Symbols: 0
Latest comments: