Download  Print this page

Advertisement

CN75/CN75e NI
powered by Android™ 6.0
Quick Start Guide
CN75NI-A6-EN-QS-01 Rev A
5/17

Advertisement

   Also See for Honeywell CN75e NI

   Related Manuals for Honeywell CN75e NI

   Summary of Contents for Honeywell CN75e NI

  • Page 1 CN75/CN75e NI powered by Android™ 6.0 Quick Start Guide CN75NI-A6-EN-QS-01 Rev A 5/17...
  • Page 2 Introduction This document is for the CN75/CN75e NI. This is the non-incendive version of the CN75. The CN75/CN75e NI can be identified by the device label verifying non-incendive certifi- cation. Warning: Explosion Hazard -Substitution of components may impair suitability for Division 2 Class I, II, III locations.
  • Page 3 Computer Features Note: Hand strap not shown. Speaker Touch Panel Good Read LED Volume Buttons Notification LED Battery Status Power Button Microphone Scan Button...
  • Page 4 Imager (LED/Laser Aperture) Speaker Port Camera Laser Safety Label Location Application Button SIM/microSD Card Socket (Located Under Battery) Battery Side Scan Button Battery Latch I/O Cover Screws...
  • Page 5 Detach Hand Strap Detach the hand strap to access to the back of the computer. Note: Battery pack shown installed. To learn more, see “Install the Battery”.
  • Page 6 Install a microSD Card Note: Format the microSD card before initial use. Note: Always power off the computer and remove the battery before attempting to install or remove a card.
  • Page 7 Install a SIM Card Note: Always power off the computer and remove the battery before attempting to install or remove a card.
  • Page 8 Install the Battery The CN75/CN75e NI mobile computer ships with a Lithium-ion 3.7 V, 4000 mAH (14.8 Wh) battery manufactured for Honeywell International Inc. We recommend use of Honeywell Li-ion battery packs. Use of any non-Honeywell battery may result in damage not covered by the warranty.
  • Page 9 être remplacées ou rechargées dans un endroit non dangereux. Utilisez UNIQUEMENT Honeywell CN75 NI batterie P/N 1000AB02 The CN75/CN75e NI mobile computer ships with a partially charged battery. Charge the battery with a 70 Series charging device for a minimum of 6 hours.
  • Page 10 Install the I/O Cover The I/O cover must be attached when using the CN75/CN75e NI in a dangerous environment. Avertissement : Le couvercle entrée-sortie doit être fi xé lorsque le CN75/CN75e NI est utilisé dans un environnement incendiaire. Remove the I/O Cover...
  • Page 11 Turn Power On/Off The computer automatically turns on when you install the battery pack. Note: You should always either power off the computer when removing the battery or place the computer in Battery Swap mode when performing a quick battery swap. To turn the computer off: Press and hold the Power button until the options menu appears.
  • Page 12 About the Home Screen Notification / Status Bar Search Bar Touch initiate a voice Home Screen search or Panel command. Touch the All Apps icon to access Favorites Tray apps and settings. Navigation Buttons To learn how to customize the Home screen, see the user guide. Navigation and Function Buttons Buttons Description...
  • Page 13 Buttons Description Function Up, Down, Move up, down, right or left Left and on the screen. Right Modifiers Press a modifier key before pressing another key to access an alternate key value or function. Alternate key values appear on the keypad overlay near the relevant key.
  • Page 14 Scan a Bar Code Note: For optimum performance, avoid reflections by scanning the bar code at a slight angle. Point the computer at the bar code. Touch and hold the Scan button. Center the aiming beam over the bar code. When the scanner successfully reads the bar code, the computer beeps, and the Good Read LED turns on briefly.
  • Page 15 Under “Computer” or “This PC”, click on the CN75. You can now copy, delete and/or move files or folders between the computer and CN75/CN75e or a microSD card installed in the CN75/CN75e as you would with any other storage drive (e.g., cut and paste or drag and drop). Restart the Computer You may need to restart the mobile computer to correct conditions where an application stops responding to the system...
  • Page 16 Use Battery Swap Mode for Battery Replacement Battery Swap mode places the computer in a low power state so that the battery can be removed for a short period of time. To activate Battery Swap mode: Press and hold the Power button until the options menu appears.
  • Page 17 Microsoft Corporation in the United States and/or other countries. Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made.

This manual also for:

Cn 75Ck75Ck75lan

Comments to this Manuals

Symbols: 0
Latest comments: