1. Manuals
  2. Brands
  3. Global Manuals
  4. Motherboard
  5. 3308200
  6. User manual

Global 3308200 User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
User's Manual
Single B oard Computer 3308200
Version 1 .0 , March 2009

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 3308200 and is the answer not in the manual?

Questions and answers

Related Manuals for Global 3308200

Summary of Contents for Global 3308200

  • Page 1 User’s Manual Single B oard Computer 3308200 Version 1 .0 , March 2009...
  • Page 2 Copyrights This manual is copyrighted and all rights are reserved. It does not allow any non authorization in copied, photocopied, translated or reproduced to any electronic or machine readable form in whole or in part without prior written consent from the manufacturer. In general, the manufacturer will not be liable for any direct, indirect, special, incidental or consequential damages arising from the use of inability to use the product or documentation, even if advised of the possibility of such...
  • Page 3 Introduction Chapter 1 Introduction Chapter 1 - Introduction...

  • Page 4: Packing List

    Introduction 1.7 Packing List  x 3308200 3.  ” Embedded Board  x Driver CD  x Quick Installation Guide If any of the above items is damaged or missing, contact your vendor immediately.

  • Page 5: Specification

    Introduction 1.9 Specification Form Factor 3.” Embedded MiniBoard Onboard Intel ® Celeron M .0GHz zero cache processor, FAB400MHz. Chipset Intel ® 82GM + Intel ® ICH4  x 200-pin SO-DIMM socket for DDR Up to GB System Memory SDRAM Intel ®...

  • Page 6: Board Dimensions

    Introduction 1.10 Board Dimensions Layout Top View Unit:mm...
  • Page 7 Introduction Layout Bottom View Unit:mm...

  • Page 8: Installing The Memory

    Introduction 1.11 Installing the Memory Side notch Latch knob Latch claw Latch section Latch arm Polarizing key To install the Memory module, locate the Memory SO-DIMM slot on the board and perform as below: . Adjust the socket polarizing key and the board key to the same direction. 2.

  • Page 9: Installation

    Installation Chapter 2 Installation Chapter 2 - Installation...

  • Page 10: Block Diagram

    Installation 2.1 Block Diagram Intel® Celeron M 1.0GHz CPU FSB 400MHz Analog R.G.B. Intel® 1 x 200pin DDR Memory Bus SO-DIMM socket 852GM LVDS LVDS USB I/F 6 x USB PCI Bus 1 x Mini PCI Intel® ICH4 IDE ATA I/F 1 x IDE Fast LAN (RJ-45)
  • Page 11 Installation 2.2 Jumpers and Connectors...

  • Page 12: Jvlcd1: Lcd Panel Voltage Select

    Installation Jumpers JBAT1: CMOS Setup (12) If the board refuses to boot due to inappropriate CMOS settings here is how to proceed to clear (reset) the CMOS to its default values. Connector type: 2.00mm pitch x3 pin header Mode Keep CMOS (Default) Clear CMOS You may need to clear the CMOS if your system cannot boot up because you forgot your password, the CPU clock setup is incorrect, or the CMOS...

  • Page 13: Ir1: Infrared Connector

    Installation Connectors INV1: LCD Inverter Connector (1) Connector type: 2.00mm pitch x-pin box wafer connector. Description +2V Backlight on/off Brightness control IR1: Infrared Connector (2) Connector type: 2.4mm pitch x pin header Description IRRX IRTX The IR connector can be configured to support wireless infrared module, user can transfer files to or from notebooks, PDA and printers.

  • Page 14: Ide1: Ide Connector

    Installation IDE1: IDE Connector (3) An IDE drive ribbon cable has two connectors to support two IDE devices. If a ribbon cable connects to two IDE drives at the same time, one of them has to be configured as Master and the other has to be configured as Slave by setting the drive select jumpers on the drive.

  • Page 15: Smbus1: External Smbus Connector

    Installation SMBUS1: External SMBUS Connector (4) Connector type: 2.4mm pitch x3 box wafer connector. Description Data Clock DIO1: Digital I/O Connector (5) DIO is a 8-bit DIO connector that supports 4-bit In/ 4-bit Out. Connector type: 2.00 mm pitch 2x pin header Description Description DIO...

  • Page 16: Jfrt1: Switches And Indicators

    Installation JFRT1: Switches and Indicators (6) It provides connectors for system indicators that provides light indication of the computer activities and switches to change the computer status. Connector type: 2.00 mm pitch 2x pin header Description Description RESET+ RESET- Power LED+ Power LED- HDD LED+ HDD LED-...

  • Page 17: Bios Setup

    Installation LPT1: Parallel Port or FDD Connector (8) LPT is shared with FDD. Connector type: 2.00mm pitch 2x0 pin header. Description Description STROBE PTD0 ERROR PTD INIT PTD2 SLIN PTD3 PTD4 PTD GND (Key) PTD6 BUSY PTD7 SELECT LPT1 can be configured as a connector floppy disk drive interface through BIOS setup.
  • Page 18 Installation USB2/ USB3: USB Connector (9), (10) USB2/ USB3 supports four USB 2.0 w/ 480MB/s by 2.00mm pitch 2x pin header Description Description USBD- USBD- USBD+ USBD+ N/C (Key) AUDIO1: Front Panel AUDIO Connector (11) Connect a tape player or another audio source to the light blue Line-in connector to record audio on your computer or to play audio through your computer’s sound chip and speakers.
  • Page 19 Installation LVDS1: LVDS LCD Connector (14) The LVDS connector supports 8-bit or 36-bit LVDS. VDD could be selected by JVLCD in +V or +3.3V. Connector type: DF-3-30DP-.2V Description Description TX2CLK+ TXCLK+ TX2CLK- TXCLK- TX2D0+ TXD0+ TX2D0- TXD0- TX2D+ TXD+ TX2D- TXD- TX2D2+ TXD2+...

  • Page 20: Kbm1: Keyboard & Mouse

    Installation KBM1: Keyboard & Mouse (18) Mini-Din Keyboard & Mouse connector Description KB Data MS Data KB Clock MS Clock Note: KBM supports PS/2 keyboard directly, and PS/2 mouse supported with the additional PS/2 -to-2 cable. VGA1: CRT Connector (19) Connector type: D-Sub -pin female.

  • Page 21: Pwr1: Power Supply Connector

    Installation PWR1: Power Supply Connector (21) Connector type: .08mm pitch x4-pin wafer connector Description +2V EATX1: ATX Feature Connector (22) Connector type: 2.4mm pitch x3-pin box wafer connector Description PS-ON V_SB FAN1: CPU Fan Power Connector (23) CPUF is 3-pin header for the system fan. The fan must be a +2V fan. Description +2V FAN_Detect...

  • Page 22: Pin Description

    Installation CFD1: Compact Flash II Socket (24) Connector type: 50-pin compact flash connector Pin Description Pin Description SDD3 SDD SDD4 SDD2 SDD SDD3 SDD6 SDD4 SDD7 SDD SDCS# SDCS3# SDIOR# SDIOW# IRQ CSEL# IDERST2# SIORDY SDA2 SDDREQ SDA SDDACK# SDA0 HD_LED2# SDD0 SDIAG#...
  • Page 23 Installation 2.3 The Installation Paths of CD Driver Driver Path AUDIO \AUDIO\REALTEK\AC97 CHIPSET \CHIPSET\INTEL\INF 6.3 \ETHERNET\INTEL\PRO 0&00 \GRAPHICS\INTEL\8X...

  • Page 24: Bios Beep Sound Code List

    BIOS 3.15 BIOS Beep Sound code list Beep Sound Message  short (Beep) System booting is normally 2 short (Beep) CMOS setting error  long -  short (Beep) DRAM error  long - 2 short (Beep) Display card or monitor connected error  long - 3 short (Beep) Keyboard error  long - 9 short (Beep)

  • Page 25: Award Bios Post Codes

    BIOS 3.17 Award BIOS POST Codes CFh Test CMOS read/write functionality C0h Early chipset initialization: Disable shadow RAM, L2 cache (socket 7 and below), program basic chipset registers Detect memory: Auto detection of DRAM size, type and ECC, auto detection of L2 cache (socket 7 and below) C3h Expand compressed BIOS code to DRAM Ch Call chipset hook to copy BIOS back to E000 &...
  • Page 26 BIOS Reserved HPM initialization (notebook platform) Reserved Check validity of RTC value; Load CMOS settings into BIOS stack. If CMOS checksum fails, use default value instead; Prepare BIOS resource map for PCI & PnP use. If ESCD is valid, take into consideration of the ESCD's legacy information;...
  • Page 27 BIOS Initialize EISA slot Reserved Calculate total memory by testing the last double last word of each 64K page; Program writes allocation for AMD K CPU Reserved Reserved 4Ch Reserved 4Dh Reserved Program MTRR of M CPU; initialize L2 cache for P6 class CPU & program cacheable range;...
  • Page 28 BIOS Reserved Reserved Reserved Enter AWDFLASH.EXE if: AWDFLASH.EXE is found in floppy dive and ALT+F2 is pressed Reserved Detect and install all IDE devices: HDD, LS20, ZIP, CDROM... Reserved Detect serial ports and parallel ports Reserved Reserved Detect and install coprocessor Reserved 7Ch Reserved 7Dh Reserved...
  • Page 29 Appendix Chapter 4 Appendix Chapter 4 - Appendix...

  • Page 30: I/O Port Address Map

    Appendix 4.1 I/O Port Address Map Each peripheral device in the system is assigned a set of I/O port addresses which also becomes the identity of the device. The following table lists the I/O port addresses used. Address Device Description 00000000 - 0000000F DMA Controller 00000080 - 0000009F...

  • Page 31: Interrupt Request Lines (Irq)

    Appendix 00000A0 - 00000A7 Hardware Monitor 00000CF8 PCI Configuration Address 00000CFC PCI Configuration Data 4.2 Interrupt Request Lines (IRQ) Peripheral devices use interrupt request lines to notify CPU for the service required. The following table shows the IRQ used by the devices on board. Level Function IRQ 0...
  • Page 32 Appendix 4.3 BIOS memory mapping Address Device Description 00000h - 9FFFFh DOS Kernel Area A0000h, BFFFFh EGA and VGA Video Buffer (28KB) C00000h - CFFFFh EGA/VGA ROM D0000h - DFFFFh Adaptor ROM E00000h - FFFFFh System BIOS...
  • Page 33 Any advice or comments about our products and service, or anything we can help you with please don’t hesitate to contact us. We will do our best to support your products, projects and business. Address: Global American, Inc. 17 Hampshire Drive Hudson, NH 03051 Telephone: Toll Free (U.S. Only) 800-833-8999...

Table of Contents