Table of Contents
Advertisement
03
Connecting your equipment
Connecting an IR receiver
If you keep your stereo components in a closed cabinet or
shelving unit, or you wish to use the sub zone remote
control in another zone, you can use an optional IR
receiver (such as a Niles or Xantech unit) to control your
system instead of the remote sensor on the front panel of
1
this receiver.
1
Connect the IR receiver sensor to the IR IN jack on
the rear of this receiver.
Closet or shelving unit
Pioneer
component
HDMI
ASSIGNABLE
1 4
COMPONENT VIDEO
ASSIGNABLE
Y
RS-232C
(OUTPUT 5 V
150 mA MAX)
EXTENSION
2
Connect the IR IN jack of another component to the
IR OUT jack on the rear of this receiver to link it to the
IR receiver.
Please see the manual supplied with your IR receiver for
the type of cable necessary for the connection.
• If you want to link a Pioneer component to the IR
receiver, see Operating other Pioneer components
with this unit's sensor below to connect to the
CONTROL jacks instead of the IR OUT jack.
Note
1 • Remote operation may not be possible if direct light from a strong fluorescent lamp is shining on the IR receiver remote sensor window.
• Note that other manufacturers may not use the IR terminology. Refer to the manual that came with your component to check for IR
compatibility.
• If using two remote controls (at the same time), the IR receiver's remote sensor takes priority over the remote sensor on the front panel.
2 • If you want to control all your components using this receiver's remote control, see Setting the remote to control other components on
page 68.
• If you have connected a remote control to the CONTROL IN jack (using a mini-plug cable), you won't be able to control this unit using the
remote sensor.
36
En
Non-Pioneer
component
CONTROL
IR
IN
OUT
IN
BD
IN
IN
IN
IN
IN
1
2
3
4
(DVD)
IN
1
IN
2
(DVR/BDR)
ZONE2
ZONE3
DVD
TV/SAT
VIDEO
DVR/
OUT
OUT
IN
IN
IN
OUT
IN
3
(VIDEO)
MONITOR OUT
ZONE 2 OUT
P
P
B
R
ANTENNA
SPEAKERS
Class 2 Wiring
AM LOOP
FM UNBAL 75
SELECTABLE
CONTROL
IR
12 V
SEE INSTRUCTIO
IN
1
TRIGGER
MANUAL
1
IN
SELECTABLE
VOIR LE MODE
(OUTPUT
D'EMPLOI
IN
2
12 V
OUT
TOTAL
2
150 mA MAX)
OUT
IR receiver
Operating other Pioneer components
with this unit's sensor
Many Pioneer components have SR CONTROL jacks
which can be used to link components together so that
you can use just the remote sensor of one component.
When you use a remote control, the control signal is
passed along the chain to the appropriate component.
Important
• Note that if you use this feature, make sure that you
also have at least one set of analog audio, video or
HDMI jacks connected to another component for
grounding purposes.
1
Decide which component you want to use the
remote sensor of.
When you want to control any component in the chain,
this is the remote sensor at which you'll point the
corresponding remote control.
2
Connect the CONTROL OUT jack of that component
to the CONTROL IN jack of another Pioneer component.
Use a cable with a mono mini-plug on each end for the
connection.
Y
RS-232C
(OUTPUT 5 V
150 mA MAX)
EXTENSION
IN
OUT
CONTROL
Continue the chain in the same way for as many
components as you have.
MONITOR OUT
ZONE 2 OUT
P
P
B
R
ANTENNA
SPEAKERS
Class 2 Wiring
AM LOOP
FM UNBAL 75
SELECTABLE
CONTROL
IR
12 V
SEE INSTRUCTIO
IN
1
TRIGGER
MANUAL
IN
1
SELECTABLE
VOIR LE MODE
(OUTPUT
D'EMPLOI
IN
2
12 V
OUT
TOTAL
2
150 mA MAX)
OUT
IN
OUT
CONTROL
2
- Quick Links:
- Specifications
Hide quick links:
Advertisement
Table of Contents
