Advertisement
Quick Links
Advertisement
Related Manuals for Gemtek Systems WLTMS-110_384041
Summary of Contents for Gemtek Systems WLTMS-110_384041
- Page 1 LTE CPE Quick installation Guide...
- Page 2 WLTMS-110_384041 Connection Guide...
- Page 3 Copyright This DOCUMENT is copyrighted with all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without the written permission of Gemtek Technology Co. Ltd. Notice Gemtek reserves the right to change specifications without prior notice.
- Page 4 Connectors 1. One RJ-45 connector for connecting to the PoE adaptor. 2. LED indicator inside and SIM card slot for inserting SIM card. 3. A grounding screw on the rear panel.
- Page 5 LED Indicators _ODU LED name Location Color LED Behavior Status Indication LED List ●●● ●●● MAIN power Blue Power On ●○○ ○○○ Power Off Ethernet Yellow ○●○ Steady ON Ethernet Connected status ○○○ Blinking Data Transmission No Ethernet action SIM status Green ○○●...
- Page 6 Installing LTE outdoor CPE Selecting a Location: LTE Outdoor CPE should be pole-mounted ● outdoors and aligned so its antenna faces the nearest LTE eNB. When selecting a suitable location for the unit, consider these guidelines: Place LTE Outdoor CPE as high as possible to achieve the best •...
- Page 7 Connecting the Cables Outdoor Connection: Connect a grounding cable between the ● Ground terminal of the LTE outdoor CPE and a good ground connection. Preparing and connecting the cable: Use only UTP-FTP ● 4x2x24AWG CAT. 5E outdoor cable from an approved manufacturer.
- Page 8 2. Connect the cable • Remove the sealing cable gland plug from the gland nut. • Open the sealing gland nut and remove it. Don not disassembles the gland base from the bracket. • Insert the cable into the sealing gland base and connect it to the RJ-45 connector at the bottom of the CPE.
- Page 9 air bubbles. • Slide the cold shrink sleeve on top of the connector. Make sure that the sleeve covers both cable connector and unit connector. • Pull the cord slowly to shrink the sleeve. Indoor Connection ● 1. It is assumed that the RJ-45 is already connected to the LTE outdoor CPE.
-
Page 10: Web Interface
Web Interface Please follow the steps below to configure your device through the web interface: Open the Web browser (Internet Explorer) and enter the Step1: default IP address of the ODU CPE, which is : http://192.168.15.1 Web browser Enter ODU administrator login username/password to access Step2: the web management interface. - Page 11 Web management interface The page shown here gets displayed in your browser after Step3: login; you can now configure the device settings. GUI Interface Mode: Operator: APN Name (More bar means better Signal: signal) (Disconnect, no signal)
- Page 12 Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
-
Page 13: Professional Installation Instruction
Professional installation instruction Please be advised that due to the unique function supplied by this product, the device is intended for use with our interactive entertainment software and licensed third-party only. The product will be distributed through controlled distribution channel and installed by trained professional and will not be sold directly to the general public through retail store. -
Page 14: Instructions D'installation Professionnelle
Instructions d'installation professionnelle Veuillez noter que l'appareil etant dedie a une fonction unique, il doit etre utilise avec notre logiciel proprietaire de divertissement interactif . Ce produit sera propose par un reseau de distribution controle et installe par des professionels; il ne sera pas propose au grand public par le reseau de la grande distribution.