Page 1
PANTONMA 2.4Ghz QUADCOPTER FEATURING: 1. Four-Rotor design allows great speed and maneuverability for both Indoor and outdoor use. 2. Built-in 6-axis Gyro ensures excellent stability. 3. Modular design for convenience of module upgrade and increasing ease of maintenance. 4. Auto Hover/Auto Launch/Auto landing/obstacle avoidance function. 5.
PANTONMA K80 Wonderful design and seperatable module could win player's favor. High pixel and stable flying could bring much more entertainment. 1.Protect Shield 2.Propeller 3.Power button (long press 1.5s to power on/off) 4.Camera Module 5.Motor 6.Battery Module 7.Obstacle avoidance module...
Keys Introduction Of K80 Remote Controller Fantastic design and multifunction are spoken highly of! Stretchable handset could fit different screens. Let's go and see! 1.Charging indicator 15.Direction control stick 2.Throttle control stick 16.Power indicator 3.Left/right turning trimmer 17.One key to launch/auto landing (long press 3 seconds 4.Power switch 5.Camera lens up...
Specification of K80 330X330X68mm Weight Aprx 135g(Standard version) Max Flight Time 6.5 MIN Operating Temperature Range to 40 Lens Angle Control Range 90° SD Card Types 4G Micro SD Card Battery Capacity 650mAh 330mm 225X120X50mm Weight 154.3g 188mm Max Transmission Charging Type Operating Temperature Range to 40...
Page 6
1.Connect the battery to the socket back of the drone. 1.Match the module with the socket at the bottom of the drone. 2.Push the module according to the direction on the module show to mount it. 1.Insert the motor to the motor base. 2.Connect the motor with the socket on the gear.
Page 7
1. Insert the blades with the main axis bar of the six angle gear. 2.Use screwdriver to tighten the screw in clockwise direction. NOTE: It is important for the correct blade to be put on the correct motor or the drone will not fly correctly. A letter is marked on each blade to indicate which motor it should go on.
Page 8
1. Push the on/off switch of the quad-copter to OFF and press the button to take out the battery. 2. Connect the USB cable to the battery pin. 3. Connect the USB cable with computer or compatible USB power adapter. The red charging light will turn off while charging and will turn on once charged.
Page 9
Connection instruction: 1.Turn on the drone, the FPV indicate light blink slowly, which shows the drone is ready to connect with phone. 2.Open your phone and into “settings” , turn on the WIFI, search the KD- **** from the signal list, connect the signal, exit “setting” option until the signal shows connected.
Push the throttle lever to the highest position, the LED light on the drone change from flickering to steady on. This shows that the quad-copter has synced with the remote. Then press the Auto take off button and push the throttle slightly to fly.
Special Function Button Guide Mount the obstacle avoidance sensor module to the bottom of the drone, when it detect that there have obstacle within 2m(depend on environment ), the drone will not keep approaching, it will avoid the obstacle automatically. The module will work automatically when it fly 80- 100cm away from ground.
The PANTONMA features 3 speed modes. Low speed is for beginners and high speed is for advanced users. Press the speed mode button to adjust speed. one sound for slow speed two sound for middle speed three sound for high speed Press the “one key to return”...
Page 13
Adjust the direction in CF mode: Before into the CF mode, it is necessary to adjust the direction first. Make sure the front of the quadcopter points ahead in the same direction of the operater (figure.1), then push the left and right control stick to the lower left direction at the same time for about 2 seconds(figure.2), the indication lights of the quadcopter change from stable on to fast flickering for 2 seconds, which means the direction adjustment is finished.
0.3MP Camera 2MP Camera 5MP Camera FPV WiFi + 0.3MP camera resolution of photo/ resolution of photo/ resolution of photo: resolution of photo/ video:640X480 video:1280X720 2592x1944 video:640X480 resolution of video: 1920x1080 FPV WiFi + 2MP FPV 5.8G with 2MP Obstacle avoidance Battery camera camera + Monitor...
Card Reader Landing gear Receiver Board Remote Control Transmit Board Problem Reason Solution 1.The quadcopter and the The indication light of the 1.Repeat the connecton transmitter are out of radio quadcopter is flashing and procedure. connection. without reaction 2.Recharge the battery 2.Insufficient battery power The quadcopter’s blades turn 1.
Page 16
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.