Page 1
ITEM # 0238999 YARD CHIPPER MODEL # 26113 CAUTION - FOR YOUR SAFETY READ YOUR OPERATOR’S MANUAL COMPLETELY AND CAREFULLY BEFORE ATTEMPTING TO SET UP OR OPERATE YOUR NEW YARD CHIPPER ALL OPERATORS OF THIS EQUIPMENT SHOULD READ AND UNDERSTAND ALL SAFETY RULES PRINTED ON THE MACHINE AND IN THIS OPERATOR’S MANUAL BEFORE USE.
GENERAL SAFETY RULES Safety is a combination of common sense, staying alert, and knowing how to use your yard chipper properly. WARNING TO AVOID MISTAKES THAT COULD CAUSE SERIOUS INJURY, DO NOT PLUG IN THE CHIPPER UNTIL THE FOLLOWING STEPS HAVE BEEN READ THOROUGHLY. 1.
Page 4
GENERAL SAFETY RULES-CONTINUED 13. ALWAYS keep tool clean and in good working order. 14. Check for proper alignment of moving parts, binding, breakage, or any other conditions that may affect the tool’s operation. Any part that is damaged should be properly repaired or replaced before use. 15.
SPECIFIC SAFETY RULES FOR YARD CHIPPERS 1. Be thoroughly familiar with the operation of the chipper before initial use. 2. NEVER put your hands into the hopper. Always use the push stick supplied with your chipper to push items into the hopper. 3.
ELECTRICAL INFORMATION WARNING: TO AVOID ELECTRIC SHOCK HAZARDS, FIRE HAZARDS, OR DAMAGE TO THE TOOL, USE PROPER CIRCUIT PROTECTION. YOUR CHIPPER IS WIRED AT THE FACTORY FOR 12O-V OPERATION. CONNECT TO 120-V, 15-Amp CIRCUIT AND USE A 15-Amp CIRCUIT BREAKER. TO AVOID SHOCK OR FIRE WHEN THE POWER CORD IS WORN, CUT, OR DAMAGED IN ANYWAY, REPLACE IT IMMEDIATELY.
Page 7
ELECTRICAL INFORMATION WARNING THIS LAWN TOOL IS FOR OUTDOOR USE ONLY. DO NOT EXPOSE TO RAIN OR USE IN DAMP LOCATIONS. GUIDELINES FOR USING EXTENSION CORDS Make sure your extension cord is in good condition. When using an extension cord, be sure to use one of heavy enough gauge to carry the current your product will draw.
ASSEMBLY AND ADJUSTMENTS UNPACKING (Fig. 3) Remove the chipper components from the packaging and examine them carefully. NOTE: Do not discard box or any packing material until all parts are examined. Fig. Part.1 Housing with hopper 1 pcs Part.7 Screw 4 pcs Part.2 Wheel...
Page 10
ASSEMBLY AND ADJUSTSMENTS ASSEMBLY INSTRUCTIONS Assembling this YARD Chipper need as follows tools: (I) T-wrench (II) wrench (III) Phillips screwdriver The chipper must be fully assembled before use. WARNING TO AVOID INJURY, ALWAYS TURN THE SWITCH OFF AND DISCONNECT THE CHIPPER FROM THE POWER OUTLET BEFORE MAKING ANY ADJUSTMENTS.
Page 11
ASSEMBLY AND ADJUSTMENTS Attach legs to chipper (see Fig.5) The legs are attached to the bottom of the chipper. 1. Place the legs (1) into the holes (4) on the housing. 2. Push firmly into place. 3. Using a screwdriver tighten the screw (3) and washer (2). NOTE: Do not overtighten the screws.
OPERATION OPERATING INSTRUCTIONS Cord Lock ON/OFF Switch (Fig. 7) The ON/OFF switch (1). A circuit breaker/reset button (2) is located beside the switch. Fig. 7 To operate the chipper: 1. Plug the chipper into a properly grounded 3-prong outlet. 2. Flip the switch (1) to the ON position.
OPERATION Chipping yard waste (Fig. 8) The chipper is designed to work on yard waste, debris, sticks and twigs up to 1-3/8 in. (35 mm) in diameter. The chipper material will accumulate directly on the ground under the chipper. CAUTION: Do not attempt to chip material that exceeds the capacity of the chipper.
MAINTENANCE WARNING ALWAYS TURN OFF THE TOOL AND UNPLUG THE POWER CORD FROM THE OUTLET BEFORE MAINTAINING THE CHIPPER. BLADE MAINTENANCE The chipper has two blades that are attached to a rotating support. When one side of a blade becomes dull, it can be turned to use the other side. Replace or properly sharpen dull blades.
MAINTENACE CLEANING WARNING TO AVOID INJURY, ELECTRIC SHOCK, OR DAMAGE TO THE CHIPPER, NEVER ALLOW A LIQUID TO FLOW INSIDE THE TOOL. • Wipe the outside of the chipper with a dry soft cloth. • Remove the hopper from the housing body before washing the inside of the hopper.
LIMITED TWO-YEAR REPAIR WARRANTY The manufacturer warrants to the original purchaser that each new product and service part is free from defects in material and workmanship and agrees to repair or replace under this warranty any defective product or part as follows from the original date of purchase.
PARTS LIST collector bag assembly 1723012 motor drive assembly 1723004 upper handle assembly 1723009 upper gearbox cover 52.1 1722021 1722001 collector bag 37.1 1721012 upper handle 52.2 0011053 bolt 1721001 collector bag support upper handle sponge 37.2 1722012 52.3 0011056 spring check ring 1723013 tie bar assembly...