Panasonic CF-18 Series Operating Instructions Manual page 28

Reinstalling Software
9 Make a selection from the menu.
When selecting [2], enter the basic partition size for the
operating system installation and press Enter .
(The data partition size is the remainder after subtract-
ing the basic partition size.)
To select [3], the initial partition size must be 6 GB or
more of the hard disk size. Reinstallation cannot be per-
formed with a small partition size.
10 At the confirmation message, press Y .
The operation of reinstallation for the hard disk starts au-
tomatically. (The operations take about 20 minutes <PC
Card-compatible> or 50 minutes <USB>.)
CAUTION
Do not cancel the reinstall procedure before it is
completed.
When a message appears instructing you to insert
the next CD, insert the recovery CD showing the
next number in the sequence, and then select [OK].
If the message "The media does not contain the cor-
rect file" appears, select [OK]. A message will ap-
pear instructing you to insert the next CD.
Confirm that the proper recovery CD has been in-
serted by opening the tray of the CD drive and then
close the tray, then select [OK].
11 After the reinstallation procedure completes, press any key.
The computer will be shut down.
<Only when using the Panasonic CD drive KXL-RW10AN>
Remove the FIRSTAID FD and the floppy disk drive.
12 Remove the recovery CD and the CD drive.
13 Turn the computer on, and press F2 while [Panasonic]
screen is displayed.
The Setup Utility will start up.
If the password has been set, enter the Supervisor Pass-
word.
14 Press F9 .
At the confirmation message, select [Yes] and press
Enter . (The Setup Utility settings will return to their
default values. Even the security settings with the excep-
tion of the password(s) will return to their default values.)
15 Press F10 .
At the confirmation message, select [Yes] and press
Enter .
16 Perform the setup procedure for Windows by following the
instructions on the screen. (
NOTE
When an UPDATE FD is to be created, follow the steps
in the readme.txt on the disk. (
17 Run the Setup Utility and change the settings where nec-
essary.
28
page 11)
page 12)
<When using a PC Card-compatible CD drive other than
the Panasonic KXL-RW10AN>
Copy the necessary drivers, from the floppy disk included
with your CD drive, to the FIRSTAID FD with the method
below. It will be necessary to edit the CONFIG.SYS file
and AUTOEXEC.BAT file on the FIRSTAID FD. When
editing the AUTOEXEC.BAT file, some CD drives require
card managers (card and socket service). See the manual
included with your CD drive for further details.
1 Start Windows and insert the FIRSTAID FD.
2 Select [start] - [All Programs] - [Accessories] - [Notepad]
- [File] - [Open], input [a:\config.sys], then select [Open].
3 Rewrite the following line and save.
Delete the following four lines.
;KXL-RW10AN DRIVER
DEVICE=A:\TOOLS\KMASMGRA.SYS
DEVICE=A:\TOOLS\KMASASPA.SYS
DEVICE=A:\TOOLS\KMASCDA.SYS /D:MSCD000
Add the driver of your CD drive.
Device=A:\DRIVER1.SYS /D: MSCD000
Rewrite this driver for the driver of your
CD drive. The driver for the PC Card will
also be necessary. Refer to the operation
manual that accompanies the CD drive.
Save the file and close [Notepad].
4 Copy the CD driver file (i.e., the driver file rewritten in
step 3 ) of the CD drive below [a:\] of the FIRSTAID
FD.
5 Set the floppy disk to the write-protect state.
After this, follow the reinstalling procedure of <Only when
using the Panasonic CD drive KXL-RW10AN>.
( page 27)