Related Manuals for Wahsega Labs WL-IC-FLMT-SIP-I-W
Summary of Contents for Wahsega Labs WL-IC-FLMT-SIP-I-W
- Page 1 Flush Mount SIP Access Control Intercom Installer’s Guide This step-by-step guide will help you install your Wahsega Labs flush mount SIP access control intercom.
- Page 2 What’s in the Box A. (1) VoIP intercom assembly B. (4) ½” Phillips head faceplate screws for ¼” drywall C. (4) 1” Phillips head faceplate screws for ½”+ drywall D. (1) 3-pin male connector for controlling door access (1) 4-pin male connector for request to exit & door status monitor www.wahsega.com Page 2...
-
Page 3: What You Will Need
What You Will Need PoE power Power-over-Ethernet (PoE) injector PoE capable switch Remote communication point SIP server Peer-to-peer device to call Network cable (Cat 5 or Cat 6) Screwdriver Small flat head screwdriver ... - Page 4 Request to Exit and Door Latch Wiring The access control intercom provides connections for controlling magnetic door latches, request to exit (RTE) functionality for buttons and/or exit motion sensors as well as door closed status monitor. www.wahsega.com Page 4...
- Page 5 Auxiliary Output (Door Control) The connector for Auxiliary Output is a 3-pin male connector used to connect and control door latches, gates and other points of entry. Pin 1 is a 200mA fused 5V DC signal intended to provide power to the coil of an external relay.
-
Page 6: Auxiliary Output Configurations
Auxiliary Output Configurations External Relay Externally Powered Device External Relay: An external relay is normally used to switch a voltage or current which is beyond the direct switching capabilities of the Auxiliary Output. Examples are higher voltages or AC signals. In this configuration, the 5V DC relay coil high side (if polarized) should be wired to Pin 1 and the low side wired to Pin 3. - Page 7 Externally Powered Device: This is normally used for a magnetic lock or other DC powered device. The Auxiliary Output on Pin 3 provides the ground return path for the external load, and the external power supply ground should be wired to Pin 2.
- Page 8 Door Status Monitor & Request to Exit The connector for RTE and door status monitor is a 4-pin male connector used to monitor door open/closed status as well as the RTE button/motion sensor functionality. Pin 1: Door status monitor line. It can be wired as a ground/open ...
- Page 9 Door Status Monitor & RTE Connector The RTE input can be wired in parallel with an RTE button and an exit motion sensor. Both RTE and door status inputs go to Normally Open (NO) connections on corresponding devices. www.wahsega.com Page 9...
-
Page 10: Flush Mount Installation
Flush Mount Installation www.wahsega.com Page 10... - Page 11 1. Install 4-11/16” square back box (minimum 2.5” deep) with multiple conduit knockouts. If using a 2.5” deep box with raised emboss or ground screw, make sure the raised portion is positioned at the top of the box. The bottom of the access control intercom needs at least 2.45”...
- Page 12 4. Connect Ethernet cable in the orientation shown in Image A, page 4. 5. Before installing the faceplate, be sure to locate and note the access control intercom’s MAC address, which is printed on a white sticker on the rear of the circuit board. 6.
-
Page 13: Backbox Specifications
Backbox Specifications Images not to scale. Larger versions available at Wahsega.com. www.wahsega.com Page 13... - Page 14 Dimensions Images not to scale. Larger versions available at Wahsega.com. www.wahsega.com Page 14...
- Page 15 Standards Compliant The indoor SIP intercom meets or exceeds the following RF emissions standards. FCC 47 CFR Part 15 Subpart B Industry Canada ICES-003 Issue 5 Cet appareil numérique de la classe A est conforme à la norme ICES-003 du Canada.
- Page 16 Flush Mount SIP Access Control Intercom WL-IC-FLMT-SIP-I-W Installation Guide Rev A 10.2.2015 www.wahsega.com Page 16...