Internet : www.vanraam.com Conformity Van Raam declares as manufacturer that the Easy Go, as described in this manual, has been produced in accordance with the 93/42/EEG guidelines, risk category 1. All products have been produced in accordance with the 2006/42/EG guidelines. The declaration of conformity can be found on the Van Raam website.
The Easy Go is meant for adults with a fluctuating health status, who want to pedal but would also like to have the option of completely switching to electric engine if they cannot cycle (anymore).
/ or theft. This scooter bike is suitable for transporting a single person. Only use original Van Raam parts and accessories. Ride carefully on roads that are slippery due to rain, ice or snow. User manual...
Page 5
Never lift the scooter bike holding the batteries or the plastic parts at the back. User manual Easy Go 16.05...
Page 6
If not, the guarantee ceases to be valid and you will be personally responsible in the event of possible damage. Specific safety parts should always be replaced by new parts! User manual Easy Go 16.05...
Make sure clothing cannot get caught in the clamping levers! Ensure that the clamping levers are always firmly tightened, even with the seat in the lowermost position! User manual Easy Go 16.05...
Page 8
Do not pull out the handlebars further than the mark. Otherwise the tube will not be deep enough in the shaft and will risk coming off, which can lead MIN INSERT to serious injuries. User manual Easy Go 16.05...
Page 9
2. Put the handlebars in the desired position and then tighten the screws considerably. 3. Slightly loosen screw [C] with an Allen key, put the handlebars in the correct (horizontal) position and then tighten the screw again. User manual Easy Go 16.05...
Adjust the angle of the headlight in a way that the center of the lightbeam is placed around ten meter before the bike. The USB port, which is located on the headlight, has no function. User manual Easy Go 16.05...
Page 11
If a component fails, it can lead to very dangerous situations. This can lead to damage or injuries to the user of the scooter bike. Any form of cracks, scratches or change in colour in load heavily loaded parts of a component indicates that the component must be replaced. User manual Easy Go 16.05...
Page 12
Also explain to the driver that the widest part of the scooter bike lies behind him / her. Let him/ her practise by riding over a few obstacles to get an idea of how wide the scooter bike is! User manual Easy Go 16.05...
Page 13
Small obstacles should be cycled over with appropriate speed. Obstacles higher than five centimetre should be avoided. Ensure that no dangerous speed develops while driving downhill and entering tunnels. Brake on time. User manual Easy Go 16.05...
The handbrakes should be used for coming to a standstill, in the cycle mode as well as the scooter mode. The parking brake should be used to avoid the scooter from rolling away on its own when left unattended. User manual Easy Go 16.05...
You can switch the lights on and off by briefly pressing the on/off button in this mode. Always turn off the electrical system when you are getting off the scooter bike. Turn the electrical system on after you have taken up your riding position. User manual Easy Go 16.05...
Page 16
You can change the level while cycling. 3. Start assist The start assist is not available with the Easy Go scooter bike. 4. Battery indication lights The level of charge in the battery is given by five LED lights: four of these are green, the one on the left can show either green or red, if charge is low.
Page 17
Bike application The smart display is equipped with a Bluetooth connection. The Van Raam application can connect with the bike and track your bike data. In addition, settings can be changed while cycling. Once the smart display is ready to connect to the smartphone, the on/off button briefly turns blue.
Page 18
8. Put the battery back in the holder of the cycle and close the lock. If necessary, the battery can also be charged directly on the cycle. Do not wait until the battery is completely empty. It is better to top-up the battery regularly. User manual Easy Go 16.05...
Page 19
The action radius depends on a lot of different factors and is strongly influenced by: capacity and voltage of the battery, degree of support that is used, temperature, wind speed, tyre pressure, cycling speed, weight of the user and the luggage, use of gearing etcetera. User manual Easy Go 16.05...
Page 20
Only use the charger indoors and in non-humid environments, the charger may not get wet. Only use the Van Raam supplied battery. Only charge the battery with the supplied charger! The battery housing ánd charger housing may never be opened! When there is a problem, contact your dealer.
The crank shortener is fitted to the crank, as illustrated. The pedal can then be fitted into the crank shortener at two positions. With the Allen screw [A] the crank shortener should be aligned with the crank. two assembly points pedal User manual Easy Go 16.05...
Page 22
Then remove the PCB [C] from the holder. You can now replace the battery [D]. This is a 3 volt lithium battery of the type CR123A. Batteries cause environmental pollution. Follow the local regulations during disposal. User manual Easy Go 16.05...
Turning radius (mm) 1800 Action radius* (km) The Easy Go is normally delivered with three levels for the speed; 5 km/h, 10 km/h and 15 km/h Gas operation using thumb throttle, or electric assistance while pedaling. * With the standard battery (11.2 Ah), fully electrical operation with normal use.
If you still decide you want to replace components yourself, you are responsible for damage or harm due to incorrectly fitted components. Only use original Van Raam spare parts, which you can buy at you dealer. If requested the dealer will make the necessary information on repair and maintenance available.
1. Loosen the cap nut a few turns with a socket spanner. 2. Move the chain tension wheel, so that the chain is under light tension, as described above. 3. Tighten the cap nut again. User manual Easy Go 16.05...
Page 26
(Remember to tighten both the nuts equally.) 3. Tighten the socket screws of the engine bracket slightly. 4. Check if the chain tension is correct. 5. Tighten the nuts firmly. User manual Easy Go 16.05...
This is also the case if unauthorized maintenance is carried out or if technical changes or additions are made with non- original Van Raam parts without permission of Van Raam. The original CE certification will become nul-and-void if modifications are done by third parties. The absence of the certification can lead to problems in insuring your bike, and for any loss or incurred.
The frame number is printed on the sticker. This sticker is located on the frame, see illustration. Example of sticker: XXXXX Position of sticker: CE marking on the handle stem Frame number on the handle stem User manual Easy Go 16.05...
The following items are changed to the bike: Changed: Date: Carried out: Beware! Please note that if changes are made by a non-authorized Van Raam dealer or no original Van Raam parts or options are used, warranty may void. User manual Easy Go 16.05...
Page 30
Here you have space to take notes or write down the maintenance on your bike: User manual Easy Go 16.05...
Page 31
Here you have space to take notes or write down the maintenance on your bike: User manual Easy Go 16.05...
Page 32
ISO 9001: 2008 quality standards. Van Raam has been certified by TÜV Rheinland Netherlands BV. You will especially enjoy your Van Raam bike when the bike is adjusted to your specifications and when the instructions in the user manual are followed. Pay special attention on the service intervals who specified in the manual of the bike.