Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for RAMVAC OWL TOUCH
Summary of Contents for RAMVAC OWL TOUCH
- Page 1 OUCH YSTEM...
- Page 2 Four different categories of devices can be controlled through a single OWL Touch panel: Vacuum Units RAMVAC brand vacuum units with the new S2 control can be easily plugged into the OWL Touch and will display maintenance notifications, fault messages and other system data. However even non- RAMVAC vacuum units can be controlled via an OWL Interface Control attached to the OWL Touch.
- Page 3 OWL Hub OWL Hub Assembly comes in four port, eight port and sixteen port versions. This is the number of devices that can be connected to the system. 1056DOC – REV E Page 3...
- Page 4 SYSTEM INSTALLATION Parts List Qty 1 OWL Touch Display with junction box. Mounts to standard 2-gang electrical box (not included). Qty 1 OWL Hub Qty 1 Power Supply Note: RAMVAC offers shielded CAT6 Ethernet cables in various lengths for non-plenum installations.
- Page 5 Connect CAT6 Shielded Ethernet cables (standard RJ-45 connectors) to the Owl Hub for all devices being controlled by the system as well as the cable running from the office area for the Owl Touch panel. DO NOT CONNECT THE CABLE AT THE TOUCH PANEL IN THE OFFICE AT THIS TIME.
- Page 6 CONNECT STEP ETHERNET CABLE TO OWL TOUCH PLUG IN STEP POWER SUPPLY & CONNECT TO HUB CONNECT ALL STEP CABLES TO HUB PORTS WATER VALVE • NON-RAMVAC VACUUM PUMP STEP CONNECT CABLES TO • NON-RAMVAC AIR COMPRESSOR • DEVICE "COM" PORTS AUXILIARY DEVICE •...
- Page 7 TOUCH PANEL MOUNTING ATTENTION!!! DELICATE GLASS Do not over-tighten mounting screws. Tighten carefully only until unit is secure. Touch panel enclosure mounts to standard two-gang wall box with 4 included screws. Ethernet cable connection will be at the bottom of the box for proper screen orientation.
- Page 8 Each vacuum or compressor should display "Local Standby" on the C2 or S2 Control LCD screen. Also ensure the screen is illuminated on the OWL Touch Display in the office area. The system is now ready to be programmed.
- Page 9 Hub circuit board. Owl Hub PCB Board Press and hold Baseline button for 10 seconds. All equipment is now ready to be operated by the OWL Touch system. All C2 and S2 screens should display "OWL Stand-by". • IMPORTANT: All air compressors are to be connected to the same air piping network and should not be isolated pneumatically.
- Page 10 Select Exit from the keyboard screen to store the information. The date and time of day will need to be set in the OWL Touch. • From the System Setup screen and select “Set Time”. The screen below will now be shown 1056DOC –...
- Page 11 Save and then Exit. The daily schedule in the OWL Touch will need to be programmed next. Each day of the week can be set. Note this is an optional feature that allows the OWL system to activate all connected equipment on the programmed schedule.
- Page 12 The following procedure is used to set the “Low Vacuum Set Point” for systems with more than one RAMVAC power unit. The OWL uses this parameter to automatically turn on more power units when vacuum level drops below the set level. When vacuum level is higher than the “Low Vacuum Set Point”, the OWL system runs only one power unit to conserve power and optimize runtime.
- Page 13 • Select “Vac Set”. The menu below is now shown. • The current vacuum level is indicated in the top field. • Notice the number of units currently running on the bottom of the screen. If more than 1 unit is running, use the "-"...
- Page 14 OWL SYSTEM OPERATION Two “Run Modes” are available from the OWL Touch “Home Screen”. The system can be operated in either “Manual” or “By Schedule” modes to turn on connected equipment. MANUAL MODE This mode allows connected equipment to be turned off and on using the four ON/OFF buttons directly above the run mode box.
- Page 15 (800) 5-RAMVAC FAX (605) 642-3776 www.ramvac.com © Copyright 2012 RAMVAC Dental Products. All rights reserved. No part of this publication may be copied or distributed, transmitted or transcribed in any form or by any means without the expressed written permission of...
Need help?
Do you have a question about the OWL TOUCH and is the answer not in the manual?
Questions and answers