Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for MC PCI-DAS1001
Summary of Contents for MC PCI-DAS1001
- Page 2 PCI-DAS1001 Multifunction Analog & Digital I/O User's Guide Document Revision 3A, March, 2009 © Copyright 2009, Measurement Computing Corporation...
- Page 3 Measurement Computing Corporation products are not designed with the components required, and are not subject to the testing required to ensure a level of reliability suitable for the treatment and diagnosis of people. HM PCI-DAS1001.doc...
- Page 4 Trademark and Copyright Information TracerDAQ, Universal Library, Measurement Computing Corporation, and the Measurement Computing logo are either trademarks or registered trademarks of Measurement Computing Corporation. Windows, Microsoft, and Visual Studio are either trademarks or registered trademarks of Microsoft Corporation LabVIEW is a trademark of National Instruments. CompactFlash is a registered trademark of SanDisk Corporation.
-
Page 5: Table Of Contents
Software features ..............................7 PCI-DAS1001 block diagram ..........................8 Chapter 2 Installing the PCI-DAS1001 ........................9 What is included with your PCI-DAS1001 ......................9 Hardware ..................................9 Additional documentation ..............................9 Optional components ................................ 9 Unpacking the PCI-DAS1001 .......................... 10 Installing the software ............................ -
Page 6: Preface
About this User's Guide What you will learn from this user's guide This user's guide explains how to install, configure, and use the PCI-DAS1001 so that you get the most out of its analog, digital, and timing I/O features. This user's guide also refers you to related documents available on our web site, and to technical support resources that can also help you get the most out of your board. -
Page 7: Register-Level Programming
You should use the Universal Library to control your board. Only experienced programmers should perform register-level programming. If you need to program at the register level in your application, refer to the Register Map for the PCI-DAS1001 Series (available at www.mccdaq.com/registermaps/RegMapSTC1000.pdf). -
Page 8: Introducing The Pci-Das1001
Introducing the PCI-DAS1001 Overview: PCI-DAS1001 features This manual explains how to install and use the PCI-DAS1001. This board is a multifunction analog and digital I/O board designed for the PCI bus. The PCI-DAS1001 provides either 16 single-ended or eight differential analog inputs. Input ranges are software-selectable as either bipolar or unipolar. -
Page 9: Pci-Das1001 Block Diagram
PCI-DAS1001 User's Manual Introducing the PCI-DAS1001 PCI-DAS1001 block diagram PCI-DAS1001 functions are illustrated in the block diagram shown here. Figure 1. PCI-DAS1001 functional block diagram... -
Page 10: Installing The Pci-Das1001
If you ordered any of the following products with your board, they should be included with your shipment. C100FF-x cable Signal termination and conditioning accessories MCC provides signal termination and conditioning products for use with the PCI-DAS1001. Refer to the "Field wiring and signal termination" section for a complete list of compatible accessory products. -
Page 11: Unpacking The Pci-Das1001
Quick-Start.pdf. Installing the hardware The PCI-DAS1001 board is completely plug-and-play. There are no switches or jumpers to set on the board. Configuration is controlled by your system's BIOS. To install your board, follow the steps below. Install the MCC DAQ software before you install your board The driver needed to run your board is installed with the MCC DAQ software. -
Page 12: Differential Input Mode
PCI-DAS1001 User's Manual Installing the PCI-DAS1001 Differential input mode When all channels are configured for differential input mode, eight analog input channels are available. In this mode, the input signal is measured with respect to the low input. The input signal is delivered through three wires: ... -
Page 13: Pinout - Main I/O Connector
PCI-DAS1001 User's Manual Installing the PCI-DAS1001 Pinout – main I/O connector 8-channel differential mode Signal Name Signal Name PC +5V A/D Int. Pacer Output A/D External Trigger PC -12V A/D External Pacer PC GND CTR4 OUT PC +12V CTR4 GATE... - Page 14 PCI-DAS1001 User's Manual Installing the PCI-DAS1001 16-channel single-ended mode Signal Name Signal Name PC +5V A/D Int. Pacer Output A/D External Trigger In PC -12V A/D External Pacer PC GND CTR4 OUT PC +12V CTR4 GATE PC GND CTR4 CLK...
-
Page 15: Cables
PCI-DAS1001 User's Manual Installing the PCI-DAS1001 Cables Cable is labeled “Pins 1-50”. The red stripe identifies pin # 1 Cable is labeled “Pins 51-100”. The red stripe identifies pin # 51 Figure 2. C100FF-x cable Field wiring and signal termination The table below lists the MCC screw terminal and signal conditioning boards that are compatible with the PCI-DAS1000. -
Page 16: Calibrating The Board
Calibration theory PCI-DAS1001 series boards are shipped fully calibrated from the factory with calibration coefficients stored in nvRAM. When using Universal Library at run time, these calibration factors are loaded into system memory and are automatically retrieved each time a different DAC/ADC range is specified. -
Page 17: Chapter 4 Specifications
Chapter 4 Specifications Typical for 25 °C unless otherwise specified. Specifications in italic text are guaranteed by design. Analog input Table 1. Analog input specifications Parameter Specification A/D converter type 7800 Resolution 12 bits Number of channels 8 differential or 16 single-ended, software selectable Input ranges ±10 V, ±1 V, ±0.1 V, ±0.01 V, 0 to 10 V, 0 to 1 V, 0 to 0.1 V, 0 to 0.01 V. -
Page 18: Analog Output
PCI-DAS1001 User's Manual Specifications Analog output Table 2. Analog output specifications Parameter Specification D/A type AD7847AR Resolution 12 bits Number of channels Output ranges ±10 V, ±5 V, 0 to 5 V, 0 to 10 V. Each channel independently programmable. -
Page 19: Counter Section
PCI-DAS1001 User's Manual Specifications Counter section Table 4. Counter specifications Parameter Specification Counter type 82C54 Configuration Two 82C54 devices. 3 down counters per 82C54, 16 bits each Source: ADC Clock. 82C54A: Counter 0 - ADC residual sample Gate: Internal programmable source. -
Page 20: Main Connector And Pin Out
PCI-DAS1001 User's Manual Specifications Environmental Table 6. Environmental specifications Parameter Specification Operating temperature range 0 to 70 °C Storage temperature range -40 to 100 °C Humidity 0 to 90% non-condensing Main connector and pin out Connector type 100-pin high density Robinson Nugent Compatible cable C100FF-x, unshielded ribbon cable. -
Page 21: 8-Channel Differential Mode Pin Out
PCI-DAS1001 User's Manual Specifications 8-channel differential mode pin out Signal Name Signal Name LLGND FIRSTPORTA Bit 0 CH0 IN HI FIRSTPORTA Bit 1 CH0 IN LO FIRSTPORTA Bit 2 CH1 IN HI FIRSTPORTA Bit 3 CH1 IN LO FIRSTPORTA Bit 4... -
Page 22: 16-Channel Single-Ended Mode Pin Out
PCI-DAS1001 User's Manual Specifications 16-channel single-ended mode pin out Signal Name Signal Name LLGND FIRSTPORTA Bit 0 CH0 IN FIRSTPORTA Bit 1 CH8 IN FIRSTPORTA Bit 2 CH1 IN FIRSTPORTA Bit 3 CH9 IN FIRSTPORTA Bit 4 CH2 IN FIRSTPORTA Bit 5... -
Page 23: Declaration Of Conformity
Category: Information technology equipment. Measurement Computing Corporation declares under sole responsibility that the product PCI-DAS1001 to which this declaration relates is in conformity with the relevant provisions of the following standards or other documents: EC EMC Directive 2004/108/EC: Electromagnetic Compatibility, EN 61326-1:2006 (IEC 61326-1:2005) Emissions: Group 1, Class B ... - Page 24 Measurement Computing Corporation 10 Commerce Way Suite 1008 Norton, Massachusetts 02766 (508) 946-5100 Fax: (508) 946-9500 E-mail: info@mccdaq.com www.mccdaq.com...
Need help?
Do you have a question about the PCI-DAS1001 and is the answer not in the manual?
Questions and answers