Advertisement
Do not plug the printer to electrical wall outlets that are already being used by
equipment that could cause electrical noise and excessive voltage fluctuations
(fans and air conditioners, large photocopiers, lift motors, TV radio transmitters
and signal generators, high frequency safety devices, and so on).
•
During machine storage and operation, make sure that condensation
does not form as the result of extreme environmental variations. Dust,
dirt and smoke can cause the parts in motion to wear excessively, short
circuits (in the presence of a high degree of humidity). High
temperatures and low humidity can cause problems due to static
electricity.
•
Do not put printer to the high tempture, shake or wet environment. And
no exposure to direct sunlight. For example boiler, humidifier or fridge.
•
A stable level surface for placement.
•
A clean,well-ventilated, and big enough environment for client.
INSTALLATION OF ALIGNMENT UNIT AND RIBBON CARTRIDGE
The alignment unit is important part of printer to align paper and rub paper. As
same to ribbon cartridge, alignment unit is packaged alone to avoid been
damaged in transport.
Description of lift handle
User can rise and fall lift handle up and down(replacement) to install and
take down alignment unit and ribbon cartridge expediently, and service the
printer easily. Before using lift handle please open the top cover firstly. The
position of lift handle is refered to
Figure11.5-1, 13.
Figure11.5-1 descripton of lift handle
Rise the lift handle
Open the top cover, buttress the bottom of shell with right hand and
fasten the lift handle with left hand. Rise the lift handle gently,and
make framwok layback rise till to it been locked.
Fall the lift handle
Buttress the bottom of shell with right hand and fasten the lift handle
with lft hand. Pull the lift handle gently and make the up framework
touch the below framewok and been locked.
Warning: do not loosen hands in rising or falling the lift handle
optionally to avoid hands to be hurt.
INSTALL ALIGNMENT UNIT
DESCRIPTION OF ALIGNMENT UNIT
The alignment unit is important part of printer to align paper and rub paper.
As same to ribbon, alignment unit is packaged alone to avoid been
damaged in transport. Alignment unit's position is refered to Figure11.5-2.
The definition of term are :
(A), (B): Alignment unit's installation position on framework.
(1), (2): Lock blocks' postion. After been installed alignment unit will be
locked
by these two blocks.
(3): Alignment unit
Figure11.5-2 description of alignment unit
INSTALL ALIGNMENT UNIT
Make sure the power has been shut down.
Open the top cover and inspect if the black iron clip, yellow label and 4
foam-rubber cushions have been taken out. If not, please take out of
them refered to PACKING BOX.
Install alignment unit
Using the lift handle to rise the up framewok completely, please
notice that the paper blocking device should be sink here.
Insert alignment unit in direction about 45°into flute on the below
framework.
Press down the alignment unit to make the framewok lock the
block on the alignment unit.
Fall the lift handle and close the top cover.
WARNING: If the paper blocking device does not sink when user
install the alignment unit, or before user wants to re-install
alignment unit which has been taken out, it requires user
to make the paper blocking device sink. After paper
blocking device sinked user can install the alignment unit
to avoid damage of alignment unit ,blocked badly by
rasied paper blocking device.
INSTALLATION OF RIBBON CARTRIDGE
Figure1.5-1
Definition of terms:
1 ribbon cartridge
2 active wheel
3 fixation axle
4 fixation block
5 ribbon
6 ribbon guide
7 protective foil
•
Take out the ribbon cartridge from plastic wrapping bag. Take the lock
slice away, which is located between ribbon cartridge and ribbon guide
for transportation protection. Please refer to the
•
Open top cover and using print unit lift handle to lift the print unit
entirely.
•
Move print head to the centre and insert the fixation axles at the both
ends of ribbon cartridge into the slots at both ends of print unit frame.
Please refer to the
Figure 1.5-3.
•
Try to push ribbon cartridge by rotation as shown in
are any resistance, please rotate active wheel slightly. Insert ribbon
cartridge fixation block into both ends slot of print unit
Figure 1.5-3
•
Insert ribbon guide into print head and press it up to make sure that two
dowels on the ribbon guide have been fixed. Please refer to the
figure 1.5-4.
.
figure 1.5-1
. If there
figure 1.5-3
Advertisement
