Table of Contents
Advertisement
transfer calls to be answered by the operator back to the
designated wired PBX operator. System administrators must
know the proper programming and "call transfer" feature code
(available from the user manual of the wired PBX system) in
order to perform this function correctly.
- The following example is the instruction to route a call back to
the brand N's PBX system by pressing "Flash-7-0-1-8-3-0",
where a Flash key is pressed followed by the call transfer code
"70", then enter the extension number "1830" immediately.
Confirm the set up by press using the
Notes:
1. Only administrator can change AA settings.
2. Because AA setting is stored on the base station, the handset must be in range
with the base to make changes.
3. The maximum recording time for the greeting message is 128 seconds.
4. Allowing each line's AA to be turned on or off separately is useful if different
lines are used for different purposes.
5. When AA is disabled, the line can be dedicated to either an individual Handset
ID or a Group ID.
6. The operator can be any individual handset or a group; it doesn't need to be
an administrator handset (Handsets 10 and 11).
7. The minimum number of rings before the AA picks up cannot be lower than
two for the purpose of receiving the Caller ID message.
Line Dedication (Register to PRO base only)
1
Line dedication function can be performed by administrator handsets (ID 10
and 11) only.
2
By default all incoming calls will ring all handsets.
3
With the administrative handset, press MENU-
setting.
4
It will first show Line 1 and line status. If you wish to dedicate line 1 to a
specific handset or group, you need to press OK. To dedicate lines 2-4 use
or
scrolling key on the keypad.
5
After choosing a line, it will show
to enter the handset ID or group ID for extension number. If you choose NO,
it will go back to Line Setting menu.
Notes:
SAVE
(Left softkey).
9
–
2
-
2
for Line Dedication
YES
and NO, when choosing YES, you need
~43~
1. When entering Line Dedication setting, it will show line and status. If line is
already dedicated to a specific handset or group, it will show the handset or
group ID behind the line. If line isn't dedicated to a specific handset yet, it will
show "ALL HS" behind the line.
2. When setting Line Dedication, make sure the handset or group ID is correct to
avoid losing calls sent to an DuraWalkie handset or invalid ID.
3. Handsets dedicated to a port will also receive calls from non-dedicated line as
well as the handset's dedicated line. Use Line Dedication for a group on other
lines to further manage calls
Line Selection (Register to PRO base only)
1.
Press
MENU
-
5
-
8
while the phone is in standby to enter Line Select menu.
2.
Use
or
to switch between
3.
If set to On, when pressing
pressing
key, the handset LCD display will show "Select Line" followed by
available lines (1~4). Select from one of the available lines i.e. press
select line 1 and press
2
to select line 2.
4.
This feature is also supported when selecting a second line during call
conferencing.
Change System and Line Settings by Administrator (Register to PRO
base only)
1. There are two system parameters that can be changed by the administrator:
clear (de-register) handset ID and set the next handset ID to be assigned by the
base.
2. From an administrator handset (Handset 10 or 11), press MENU(Right) soft key.
3. Press number
9
, this will enter the administration menu.
4. Press number
1
, handset enters System setting menu.
a.
Dial tone:
Press
1
to set up the dial tone to be either "Tone" or "Pulse." Press
choose "Tone" or press
2
to choose "Pulse."
b. Flash time:
On
and Off, default = Off.
or entering a phone number followed by
1
~44~
to
1
to
Advertisement
Table of Contents
